Search

In power system operation, transmission congestion can drastically limit more economical generation units from being dispatched. In this paper, optimal transmission switching as a congestion management tool is utilized to change network topology which, in turn, would lead to higher electricity market efficiency. Transmission switching (TS) is formulated as an optimization problem to determine the most influential lines as candidates for disconnection. In order to relieve congestion without violating voltage security, TS is embedded in an optimal power flow (OPF) problem with AC constraints and binary variables, i.e., a mixed-integer nonlinear programming (MINLP) problem, solved using Benders decomposition. Also, a methodology is presented which provides a guideline to the system operator showing the order of switching manoeuvres that have to be followed in order to relieve congestion. It is also shown that TS based on DC optimal power flow (DCOPF) formulation as used in the literature may jeopardize system security and in some cases result in voltage collapse due to the shortcomings in its simplified models. In order to evaluate the applicability and effectiveness of the proposed method, the IEEE 57-bus and IEEE 300-bus test systems are used. [ABSTRACT FROM PUBLISHER]

This paper explores methods to coordinate aggregations of thermostatically controlled loads (TCLs; including air conditioners and refrigerators) to manage frequency and energy imbalances in power systems. We focus on opportunities to centrally control loads with high accuracy but low requirements for sensing and communications infrastructure. We compare cases when measured load state information (e.g., power consumption and temperature) is 1) available in real time; 2) available, but not in real time; and 3) not available. We use Markov chain models to describe the temperature state evolution of populations of TCLs, and Kalman filtering for both state and joint parameter/state estimation. A look-ahead proportional controller broadcasts control signals to all TCLs, which always remain in their temperature dead-band. Simulations indicate that it is possible to achieve power tracking RMS errors in the range of 0.26%–9.3% of steady state aggregated power consumption. We also report results in terms of the generator compliance threshold which is commonly used in industry. Results depend upon the information available for system identification, state estimation, and control. Depending upon the performance required, TCLs may not need to provide state information to the central controller in real time or at all. [ABSTRACT FROM PUBLISHER]

Hybrid series compensation using static synchronous series compensator (SSSC) and passive series capacitor can improve the stability of the system, increases the power transfer capability and is useful for the fast control of power flow. This paper analyzes the subsynchronous resonance (SSR) characteristics of the hybrid series compensated power system in detail and proposes a simple method for the extraction of subsynchronous components of line current using filter. The extracted subsynchronous frequency component of line current is used to inject a proportional subsynchronous voltage in series with the transmission line which suppresses subsynchronous current in the transmission network. This novel technique is termed as subsynchronous current suppressor. The design of subsynchronous current suppressor is based on damping torque analysis and using genetic algorithm. A novel graphical representation of series resonance condition when SSSC is incorporated in the system is presented. The detailed study of SSR is carried out based on eigenvalue analysis, transient simulation and damping torque analysis. The results of the case study on a system adapted from IEEE First Benchmark Model demonstrates the effectiveness and robust performance of subsynchronous current suppressor in damping of SSR under various system operating conditions. [ABSTRACT FROM PUBLISHER]

In this paper, an electromagnetic transient model for fixed-speed wind turbines equipped with induction generators is developed and implemented in PSCAD/EMTDC. The model is comprised by: an induction generator, aerodynamic rotor, and a two-mass representation of the shaft system. Model validation is conducted by measurement comparison using recordings obtained from switching operations performed at the Nysted Offshore Wind Farm in Denmark. A sensitivity analysis is performed to determine the impact of different model parameters on the simulated response as compared with measurements. This validated model will be used for assessing induced overvoltage conditions that may arise under switching operations similar to those captured by the measurements used for validation. [ABSTRACT FROM PUBLISHER]

Following a line outage, the fast corrective operations of transmission line switching might be used to regain N-1 security of the system without generation re-dispatch or load shedding. The problem to find feasible switching operations can be formulated as a constraint satisfaction problem (CSP). Feasibility checking, however, is difficult since changes in load flows caused by line switching operations are discontinuous, and many contingency cases need to be examined. In this paper, DC flow is considered for simplicity, and variables include binary line statuses and continuous phase angles. Security constraints for the base case, N-1, and selected N-2 cases are formulated in a unified way by using a separate set of phase angles for each case. The problem is solved by using constraint programming (CP), and a tree search procedure is developed. Since it is time consuming to handle continuous variables in the tree search, only binary variables are branched on. Once reaching a leaf node where the topology is fixed, the constraints become linear DC flow feasibility conditions and are examined by solving a linear programming problem. Effectiveness of the method is demonstrated on IEEE 30-bus and 118-bus systems. [ABSTRACT FROM PUBLISHER]

The influence of wind turbine generators (WTGs) on power system dynamic performance is becoming increasingly important as wind generation grows. The dynamic behavior of WTGs should therefore be thoroughly understood. The paper analyzes dynamic models of type-3 WTGs, and in particular the WECC generic model. The behavior of such models is governed by interactions between the continuous dynamics of state variables, and discrete events associated with limits. It is shown that these interactions can be quite complex, and may lead to switching deadlock that prevents continuation of the trajectory. Switching hysteresis is proposed for eliminating deadlock situations. Various type-3 WTG models include control blocks that duplicate integrators. It is shown that this leads to non-uniqueness in the conditions governing steady-state, and may result in pre- and post-disturbance equilibria not coinciding. It also gives rise to a zero eigenvalue in the linearized WTG model. [ABSTRACT FROM PUBLISHER]

In power system reconfiguration, the status (ON/OFF) of switches are optimized such that maximum power is delivered to loads after the occurrence of a fault. The optimized reconfiguration is achieved by prioritizing power delivered to vital loads over semi-vital and nonvital loads. The formulation presented in this paper considers a new balanced hybrid (AC and DC) shipboard power system (SPS). Analysis of the nonconvex reconfiguration formulation is done by an appropriate nonconvex solver and by convex approximation. Unlike the nonconvex solution that is based on branch-and-bound methods, convex approximation significantly reduces complexity. It is shown that for the hybrid SPS reconfiguration problem, low complexity convex approximations are effective in finding optimal solutions. Cumulative distribution function (CDF) of the power delivered to loads is presented to showcase the system robustness against random fault scenarios. A combined objective of maximizing power delivery and minimizing the number of switching actions is included in the analysis. Tradeoff between power delivered and number of switching operations after reconfiguration has been discussed at steady state. A separate analysis is also included to observe the intermediate dynamic switch states while the reconfiguration is in progress to capture the trade-off more prominently. [ABSTRACT FROM PUBLISHER]

Due to the lack of feeder corridors, the Chinese utility companies frequently choose the technique of putting multiple overhead feeders on a same tower (MFST) to meet the load demand in a heavy load area. In many situations, the distance among the feeders of MFST in an electrical distribution network (EDN) is usually too small to meet the requirements of safety regulation for repairing and maintenance. Therefore, when a fault occurs on a feeder of MFST, the other feeders have to be in a triggered passive outage (TPO) state to assist the repairing of the failed feeder. This paper presents a reliability evaluation algorithm for EDNs containing MFST using the section technique. The definition of TPO and the equivalent TPO rate and TPO duration are also proposed. Based on the TPO parameters and the section technique, the reliability evaluation algorithm containing the MFST can be obtained. Case studies on the modified RBTS-BUS6 and the EDNs of three districts in Dongguan city, China, show that the MFST has a significant impact on the EDN reliability and should be considered in the reliability evaluation. The results also show the effectiveness and applicability of the proposed approach. [ABSTRACT FROM PUBLISHER]

Power system voltage security assessment is generally applied by considering the power system loadability surface. For a large power system, the loadability surface is a complicated hyper-surface in parameter space, and local approximations are a necessity for any analysis. Unfortunately, inequality constraints due to for example generator overexitation limiters and higher codimension bifurcations makes the loadability surface nonsmooth. This makes the use of local approximations limited and calls for a method for estimating the distance to a nonsmooth part of the surface. This paper suggests a method for calculating the distance from a point on the loadability surface to the closest point of nonsmoothness of the loadability surface. [ABSTRACT FROM PUBLISHER]

This paper addresses the issue of improving the conventional iterative method used for integrated extended equal area criterion (IEEAC) and single machine equivalent (SIME) for multi-swing transient stability limit analysis in power system operation. Effects of the complicated phenomena on the conventional method, i.e., nonmonotonic variation of the stability margin and the isolated stability domain (ISD), are studied. Accordingly, the conventional method is improved for both efficiency and accuracy. With this knowledge, an improved sensitivity-based iterative method for searching multi-swing transient stability limit is proposed. The advantage of this method is that the complicated phenomena are fully considered and their effects are either overcome or avoided as much as possible. Case studies on the ten-generator New England power system are presented to verify the effectiveness and efficiency of this improved method. [ABSTRACT FROM PUBLISHER]

Electrical distribution network reconfiguration is a complex combinatorial optimization process aimed at finding a radial operating structure that minimizes the system power loss while satisfying operating constraints. In this paper, a harmony search algorithm (HSA) is proposed to solve the network reconfiguration problem to get optimal switching combination in the network which results in minimum loss. The HSA is a recently developed algorithm which is conceptualized using the musical process of searching for a perfect state of harmony. It uses a stochastic random search instead of a gradient search which eliminates the need for derivative information. Simulations are carried out on 33- and 119-bus systems in order to validate the proposed algorithm. The results are compared with other approaches available in the literature. It is observed that the proposed method performed well compared to the other methods in terms of the quality of solution. [ABSTRACT FROM AUTHOR]

Frequency in large power systems is usually controlled by adjusting the production of generating units in response to changes in the load. As the amount of intermittent renewable generation increases and the proportion of flexible conventional generating units decreases, a contribution from the demand side to primary frequency control becomes technically and economically desirable. One of the reasons why this has not been done was the perceived difficulties in dealing with many small loads rather than a limited number of generating units. In particular, the cost and complexity associated with two-way communications between many loads and the control center appeared to be insurmountable obstacles. This paper argues that this two-way communication is not essential and that the demand can respond to the frequency error in a manner similar to the generators. Simulation results show that, using this approach, the demand side can make a significant and reliable contribution to primary frequency response while preserving the benefits that consumers derive from their supply of electric energy. [ABSTRACT FROM AUTHOR]

The Shangdu power plant has four 600-MW turbine-generators connected to the North-China Grid through two 500-kV transmissions, which are compensated with 45% fixed series capacitors. Extensive studies conducted on the system model indicate that the system suffers from multimodal subsynchronous resonance (SSR). To solve the problem, a countermeasure is developed by combining the supplementary excitation damping control (SEDC) and the torsional stress relay (TSR). In this paper, the characteristics of the SSR problem are investigated. Then the developed SEDC is presented. To validate the effectiveness of the proposed SEDC as well as the results of model studies, field tests were conducted under various operating conditions. The tests fully exposed the realistic threat of SSR in the system. Meanwhile, it is demonstrated that the developed SEDC can improve torsional damping significantly, and thus solve the multimodal SSR problem effectively. This is the first time in China that practical SEDCs have been developed and their ability to mitigate multimodal SSR has been verified in a real series-compensated system. [ABSTRACT FROM AUTHOR]

The authors discuss an article by M. Lavorato and colleagues on imposing radiality constraints in power distribution system optimization problems. They claim that the paper lacks any reference where an alternative mathematical formulation is proposed to deal with transfer nodes or zero-injection nodes. In their opinion, the possibility for transfer nodes is not realistic, being in opposition to the usual operation of the medium voltage (MV) systems where all the transfer nodes are connected to.