Search

This paper studies the feasibility of utilizing the reactive power of grid-connected variable-speed wind generators to enhance the steady-state voltage stability margin of the system. Allowing wind generators to work at maximum reactive power limit may cause the system to operate near the steady-state stability limit, which is undesirable. This necessitates proper coordination of reactive power output of wind generators with other reactive power controllers in the grid. This paper presents a trust region framework for coordinating reactive output of wind generators with other reactive sources for voltage stability enhancement. Case studies on 418-bus equivalent system of Indian southern grid indicates the effectiveness of proposed methodology in enhancing the steady-state voltage stability margin. [ABSTRACT FROM PUBLISHER]

This paper summarizes simulation based technical feasibility and cost benefit analyses of a range of off-the-shelf electrical losses reduction intervention solutions in the Isle of Wight (IoW) 11 kV distribution network in the United Kingdom (UK), assessed over a period of 45 years. Based on presented results, the paper provides a brief commentary on the merits, drawbacks, risks and recommendations associated with each considered network intervention. Among considered network interventions, the transformer auto stop-start scheme, where one of the transformers among a pair at a primary substation would be switched depending on the substation's varying load, was found to be the optimal solution, i.e., in reducing technical losses significantly and may also have a reasonable Net Present Value (NPV) with a good rate of Return on Investment (RoI) when fully implemented. [ABSTRACT FROM PUBLISHER]

This paper proposes a methodology to determine the optimal capacity of renewable distributed generation (RDG). The objective in this paper is to maximize cost-savings of energy not supplied (ENS) as well as cost-savings of energy loss according to RDG installation in a distribution network. Additionally, in order to achieve this multi-objective optimization problem, both a restoration matrix and restoration availability are newly proposed. In this case study, a practical Korea Electric Power Corporation (KEPCO) system is presented and discussed, demonstrating the performance and effectiveness of the proposed methods. [ABSTRACT FROM PUBLISHER]

This paper deals with the distribution network reconfiguration problem in a multi-objective scope, aiming to determine the optimal radial configuration by means of minimizing the active power losses and a set of commonly used reliability indices formulated with reference to the number of customers. The indices are developed in a way consistent with a mixed-integer linear programming (MILP) approach. A key contribution of the paper is the efficient implementation of the \mmb\varepsilon-constraint method using lexicographic optimization in order to solve the multi-objective optimization problem. After the Pareto efficient solution set is generated, the resulting configurations are evaluated using a backward/forward sweep load-flow algorithm to verify that the solutions obtained are both non-dominated and feasible. Since the \mmb\varepsilon-constraint method generates the Pareto front but does not incorporate decision maker (DM) preferences, a multi-attribute decision making procedure, namely, the technique for order preference by similarity to ideal solution (TOPSIS) method, is used in order to rank the obtained solutions according to the DM preferences, facilitating the final selection. The applicability of the proposed method is assessed on a classical test system and on a practical distribution system. [ABSTRACT FROM AUTHOR]

Recent years have witnessed significant interest in convex relaxations of the power flows, with several papers showing that the second-order cone relaxation is tight for tree networks under various conditions on loads or voltages. This paper shows that ac-feasibility, i.e., to find whether some generator dispatch can satisfy a given demand, is NP-hard for tree networks. [ABSTRACT FROM AUTHOR]

This paper proposes an efficient solution approach based on Benders’ decomposition to solve a network-constrained ac unit commitment problem under uncertainty. The wind power production is the only source of uncertainty considered in this paper, which is modeled through a suitable set of scenarios. The proposed model is formulated as a two-stage stochastic programming problem, whose first-stage refers to the day-ahead market, and whose second-stage represents real-time operation. The proposed Benders’ approach allows decomposing the original problem, which is mixed-integer nonlinear and generally intractable, into a mixed-integer linear master problem and a set of nonlinear, but continuous subproblems, one per scenario. In addition, to temporally decompose the proposed ac unit commitment problem, a heuristic technique is used to relax the inter-temporal ramping constraints of the generating units. Numerical results from a case study based on the IEEE one-area reliability test system (RTS) demonstrate the usefulness of the proposed approach. [ABSTRACT FROM AUTHOR]

In this paper, we propose a method to optimally set the tap position of voltage regulation transformers in distribution systems. We cast the problem as a rank-constrained semidefinite program (SDP), in which the transformer tap ratios are captured by 1) introducing a secondary-side “virtual” bus per transformer, and 2) constraining the values that these virtual bus voltages can take according to the limits on the tap positions. Then, by relaxing the non-convex rank-1 constraint in the rank-constrained SDP formulation, one obtains a convex SDP problem. The tap positions are determined as the ratio between the primary-side bus voltage and the secondary-side virtual bus voltage that result from the optimal solution of the relaxed SDP, and then rounded to the nearest discrete tap values. To efficiently solve the relaxed SDP, we propose a distributed algorithm based on the alternating direction method of multipliers (ADMM). We present several case studies with single- and three-phase distribution systems to demonstrate the effectiveness of the distributed ADMM-based algorithm, and compare its results with centralized solution methods. [ABSTRACT FROM AUTHOR]

This paper proposes a generalized approach of the per unit normalization, named complex per unit normalization (cpu), to improve the performance of fast decoupled power flow methods applied to emerging distribution networks. The proposed approach takes into account the changes envisaged and also already faced by distribution systems, such as high penetration of generation sources and more interconnection between feeders, while considering the typical characteristics of distribution systems, as the high R/X ratios. These characteristics impose difficulties on the performance of both backward-forward sweep and decoupled-based power flow methods. The cpu concept is centred on the use of a complex volt-ampere base, which overcomes the numerical problems raised by the high R/X ratios of distribution feeders. As a consequence, decoupled power flow methods can be efficiently applied to distribution system analysis. The performance of the proposed technique and the simplicity of adapting it to existing power flow programs are addressed in the paper. Different distribution network configurations and load conditions have been used to illustrate and evaluate the use of cpu. [ABSTRACT FROM PUBLISHER]

A constant or voltage-dependent load model is usually assumed in most distributed generation (DG) planning studies. However, this paper proposes several different types of time-varying voltage-dependent load models to determine the penetration level of photovoltaic (PV) units in a distribution network. Here, a new analytical expression is first proposed to size a PV unit, which can supply active and reactive powers. This expression is based on the derivation of a multiobjective index (IMO) that is formulated as a combination of three indices, namely active power loss, reactive power loss and voltage deviation. The expression is then adapted to allocate PV units while considering the time-varying load models and probabilistic PV generation. The effectiveness of the proposed approach was validated on 69- and 33-bus test distribution systems. The results showed that PV allocation with different types of time-varying load models can produce dissimilar penetration levels. [ABSTRACT FROM AUTHOR]

Voltage control plays an important role in the operation of electricity distribution networks, especially with high penetration of distributed energy resources. These resources introduce significant and fast varying uncertainties. In this paper, we focus on reactive power compensation to control voltage in the presence of uncertainties. We adopt a chance constraint approach that accounts for arbitrary correlations between renewable resources at each of the buses. We show how the problem can be solved efficiently using historical samples analogously to the stochastic quasi-gradient methods. We also show that this optimization problem is convex for a wide variety of probabilistic distributions. Compared to conventional per-bus chance constraints, our formulation is more robust to uncertainty and more computationally tractable. We illustrate the results using standard IEEE distribution test feeders. [ABSTRACT FROM AUTHOR]

Power losses estimation under time-varying distributed generation (DG) conditions usually demands several power flow simulations, which is a time-consuming task. To handle this issue, this paper proposes a method that uses the information of only one (base case) power flow to estimate the total power losses of distribution networks for any new DG condition. The method is based on the second-order power flow sensitivities, which are suitable to model the nonlinear nature of power losses. As a result, the method has the potential to speed up the solution of power losses reduction optimization problems, such as DG allocation problems, in which several DG configurations need to be considered. Moreover, a practical index is proposed to quantify the responsibility of each DG for the total power losses in a multi-DG scenario. The test results verified the validity of the proposed concept and method. [ABSTRACT FROM AUTHOR]

The discrete coordinate-descent algorithm is a practical approach that is currently used in centralized Volt/VAr Control (VVC) implementations, mainly due to its good performance and speed for real-time applications. Its viability is however challenged by the increasing number of distributed generation that contribute to the VVC solution, in addition to the conventional transformer taps and switched capacitors. This paper presents the exact computation of sensitivity factors that speed up the discrete coordinate-descent implementation, by significantly reducing the number of forward/backward substitutions in the current injection power flow method; the speed up is achieved without affecting the control setting quality of the original implementation. The optimality of the discrete coordinate-descent solutions is investigated by computing the gaps relative to mixed-integer linear programming set-points, derived from a polyhedral reformulation of the VVC problem. The sensitivity-based discrete coordinate-descent algorithm is tested starting from two initial points, the default one given by the current control set-points, and a continuous solution obtained from a linear approximation of the VVC problem. Numerical results on networks with up to 3145 nodes show that the sensitivity-based approach significantly improves the runtime of the discrete coordinate-descent algorithm, and that the linear programming initialization leads to VVC solutions with gaps relative to the mixed-integer set-points that are less than 0.5%. [ABSTRACT FROM PUBLISHER]

Soft open points (SOPs) are power electronic devices which provide interconnection between two feeders in place of normally open points in electricity distribution networks. SOPs can continuously control active power flow between feeders and inject reactive power controllably at both nodes, which can be used to provide substantial capacity support to the system. This paper provides a reliability-based method to quantify the capacity value (the additional load which can be accommodated without reducing reliability) of SOPs using the Effective Load Carrying Capability method within a Monte Carlo Simulation (MCS). Optimization of post-fault active/reactive power injections by SOPs to minimize energy not supplied is formulated (directly in matrix form) as a second-order cone programming problem. This results in very low computational times which enables embedding of the optimization problem within the MCS. The proposed methodology is applied to a modified real-world distribution network considering three different SOP sizes (5 SOPs totalling 2.5, 5, 10 MVA) across three redundancy levels (N-1, N-0.75, N-0.5), and on an unbalanced network with distributed generation. Results demonstrate capacity values ranging from 2.4–12.84 MVA. When operating under a relaxed redundancy level, the capacity value of a given SOP capacity can more than double relative to N-1. [ABSTRACT FROM AUTHOR]

This paper proposes an optimal design algorithm for distributed secondary voltage control in islanded microgrids (MGs), including communication topology and controller gains. First, upon the consensus-based secondary voltage control, the sufficient condition for network connectivity of communication topology is revealed by the reachability matrix. A multi-objective optimization criterion is first proposed for the network design, taking the convergence performance, network-relevant time delays, and communication costs into consideration. After obtaining the Pareto frontier of this multi-objective model, an optimal network is selected to meet the practical requirements. Based on static output feedback, a small-signal dynamic model of an MG installed with a secondary voltage controller is established, where the distributed secondary voltage controller can be converted into an equivalent decentralized controller. Thereby, a linear quadratic regulator is formulated for the near-optimal design of controller parameters. Our approach customizes the optimal design framework of the topology and controller, which have been largely ignored in the existing literatures. Therefore, it promises to improve the performance of distributed secondary control. The effectiveness of the proposed methodology is verified by a simulation study. [ABSTRACT FROM AUTHOR]

Smart inverters provide additional control capability to help optimize the operation of distribution systems. This paper proposes a framework for exact optimal active and reactive power dispatch of distributed photovoltaic (PV) generation, switched capacitors, and voltage regulators in large multi-phase unbalanced distribution systems. The objectives of the optimal dispatch are minimization of the energy loss, PV active power curtailment, and operations of capacitors and voltage regulators, in addition to elimination of voltage violations and reverse power flow. The optimization problem is formulated in rectangular coordinates as a nonlinear, nonconvex problem. Effective computational strategies are proposed to allow the application of predictor-corrector primal-dual interior point method to solve optimization problems in real-time with a large number of constraints and variables, including discrete variables corresponding to switched capacitors and voltage regulators. The accuracy of the numerical solution and the ability to implement the proposed framework are validated using the unbalanced multi-phase IEEE 34-bus and EPRI 2,998-bus distribution systems with 15-minute load and PV data. The results show a significant loss reduction and elimination of both voltage violations and reverse power flow. [ABSTRACT FROM AUTHOR]

Extreme weather events have a significant impact on the aging and outdated power distribution infrastructures. These high-impact low-probability events often result in extended outages and loss of critical services, thus, severely affecting customers’ safety. This calls for the need to ensure the resilience in distribution networks by quickly restoring the critical services during a disaster. This paper presents an advanced feeder restoration method to restore critical loads using distributed energy resources (DERs). A resilient restoration approach is proposed that jointly maximizes the amount of restored critical loads and optimizes the restoration times by optimally allocating grids available DER resources. The restoration problem is modeled as a mixed-integer linear program with the objective of maximizing the resilience to postrestoration failures while simultaneously satisfying grids critical connectivity and operational constraints and ensuring a radial operation for a given open-loop feeder configuration. Simulations are performed to demonstrate the effectiveness of the proposed approach using the IEEE 123-node feeder with five DERs supplying 11 critical loads and the IEEE 906-bus feeder with three DERs supplying 17 critical loads. The impacts of DER availability and fuel reserve on restored networks are assessed and it is shown that the proposed approach is successfully able to restore a maximum number of critical loads using available DERs. [ABSTRACT FROM AUTHOR]

The penetration of distributed renewable energy sources in the distribution grid is increasing considerably in the last years. This is one of the main causes that contributed to the growth of technical problems in both transmission and distribution systems. An effective solution to improve system security is to exploit the flexibility that can be provided by distributed energy resources (DER), which are mostly located at the distribution grids. Their location combined with the lack of power flow coordination at the system operators interface creates difficulties in taking advantage of these flexible resources. This paper presents a methodology based on the solution of a set of optimization problems that estimate the flexibility ranges at the distribution and transmission system operators (TSO-DSO) boundary nodes. The estimation is performed while considering the grid technical constraints and a maximum cost that the user is willing to pay. The novelty behind this approach comes from the development of flexibility cost maps, which allow the visualization of the impact of DER flexibility on the operating point at the TSO-DSO interface. The results are compared with a sampling method and suggest that a higher accuracy in the TSO-DSO information exchange process can be achieved through this approach. [ABSTRACT FROM AUTHOR]

The deployment of smart grids has facilitated the integration of a variety of investor assets into power distribution systems, giving rise to the consequent necessity for positive and active interaction between those investors and local distribution companies (LDCs). This paper proposes a novel incentive-based distribution system expansion planning model that enables an LDC and distributed generation (DG) investors to work in a collaborative way for their mutual benefit. Using the proposed model, the LDC would establish a bus-wise incentive program based on long-term contracts, which would encourage DG investors to integrate their projects at specific system buses that would benefit both parties. The model guarantees that the LDC will incur minimum expansion and operation costs while concurrently ensuring the feasibility of DG investors’ projects. To derive appropriate incentives for each project, the model enforces several economic metrics including internal rate of return, profit investment ratio, and discounted payback period. All investment plans committed to by the LDC and the DG investors for the full extent of the planning period are then coordinated accordingly. Several linearization approaches are applied to convert the proposed model into an MILP model. The intermittent nature of both system demand and wind- and PV-based DG output power is handled probabilistically, and a number of DG technologies are taken into account. Case study results have demonstrated the value of the proposed model. [ABSTRACT FROM AUTHOR]

This paper describes the principle and implementation of a new MW+MVAr-Miles charging methodology, which was developed to reflect three key cost drivers in distribution network development: the distance used to support nodal real and reactive power injection/withdrawal; the degree of support offered by the network assets; and the operating condition of the supporting assets in terms of their power factors. The inclusion of the latter driver allows the developed charging methodology to reward network users who are contributing to better power factors and better network utilization, while penalizing customers who worsen power factors and network utilization. As a consequence, the charging model is able to provide forward-looking incentives for network customers to behave in a manner to better the network condition, which will in turn help to reduce the cost of future network development. In addition, the separation of real and reactive power pricing would give network users clear indications of the cost of their reactive power draw from the network, which in turn could help them to evaluate the economics in investing in reactive power compensation devices. The proposed charging methodology is demonstrated on a practical eight-busbar distribution system with a mixed demand and embedded generation (EG). This paper results from work undertaken in a project on distribution charging methodologies for Western Power Distribution. The views in this paper expressed are not those of Western Power Distribution. [ABSTRACT FROM AUTHOR]

This paper considers future distribution networks featuring inverter-interfaced photovoltaic (PV) systems, and addresses the synthesis of feedback controllers that seek real- and reactive-power inverter setpoints corresponding to AC optimal power flow (OPF) solutions. The objective is to bridge the temporal gap between long-term system optimization and real-time inverter control, and enable seamless PV-owner participation without compromising system efficiency and stability. The design of the controllers is grounded on a dual \epsilon-subgradient method, while semidefinite programming relaxations are advocated to bypass the non-convexity of AC OPF formulations. Global convergence of inverter output powers is analytically established for diminishing stepsize rules for cases where: i) computational limits dictate asynchronous updates of the controller signals, and ii) inverter reference inputs may be updated at a faster rate than the power-output settling time. [ABSTRACT FROM PUBLISHER]

Most existing approaches for distribution network reconfiguration assume that the distribution system is (three-phase) balanced and a single-phase equivalent is used. However, distribution feeders are usually unbalanced due to a large number of single-phase loads, nonsymmetrical conductor spacing, and three-phase line topology. This paper builds on our previous work and studies feeder reconfiguration for unbalanced distribution systems with distributed generation (DG). The three-phase bus locations and sizes of DG units are determined using sensitivity analysis and nonlinear programming, respectively, and distribution feeders are reconfigured every hour based on the status of time-varying loads, output power from DG units and faults on the network while minimizing the energy loss costs and DG operating costs. Simulation results show the effectiveness and computational efficiency of the proposed approach. [ABSTRACT FROM AUTHOR]

Existing population-based Stochastic Search Algorithms (SSAs) are too time-consuming to solve dynamic optimal power flow (OPF). The solution proposed in this paper is to accelerate SSAs with memory. Two memory schemes, the similarity retrieval scheme and the mean-based immigrants scheme, are proposed and applied together to the Differential Evolution and Particle Swarm Optimizer, which are two representatives of SSAs. Experiments are conducted on modified IEEE 30-bus and IEEE 118-bus systems with changing load buses and the objective of minimizing real power transmission loss. The results show that the proposed schemes significantly improve the performance of the two existing algorithms, and that SSAs could be practical for tracking optima of dynamic OPF. [ABSTRACT FROM AUTHOR]

This paper proposes a computationally efficient technique for estimating the composite load model parameters based on analytical similarity of parameter sensitivity. When the model parameters are updated in the optimization procedure to best fit the actual load dynamics, i.e., measurements, parameters of similar sensitivity representation in the given mathematical model structure are updated in the same manner at every iterative step. This research allows for practically reducing the number of load model parameters to be identified in the estimation process and the overall computational cost while preserving the desired complexity and accuracy of the original model. This approach consequently facilitates the parameter estimation in the optimization process and helps manage increased number of parameters often criticized for adopting the dynamic composite load model via measurement-based approach. Case studies for the real power system demonstrate the computational efficiency and intact accuracy of the proposed method with reference to the existing methods of estimating all the parameters of the given composite load model independently. [ABSTRACT FROM AUTHOR]

The penetration of renewable distributed generation (DG) sources has been increased in active distribution networks due to their unique advantages. However, non-dispatchable DGs such as wind turbines raise the risk of distribution networks. Such a problem could be eliminated using the proper application of energy storage units. In this paper, optimal planning of batteries in the distribution grid is presented. The optimal planning determines the location, capacity and power rating of batteries while minimizing the cost objective function subject to technical constraints. The optimal long-term planning is based on the short-term optimal power flow considering the uncertainties. The point estimate method (PEM) is employed for probabilistic optimal power flow. The batteries are scheduled optimally for several purposes to maximize the benefits. A hybrid Tabu search/particle swarm optimization (TS/PSO) algorithm is used to solve the problem. The numerical studies on a 21-node distribution system show the advantages of the proposed methodology. The proposed approach can also be applied to the realistic sized networks when some sensitive nodes are considered as candidate locations for installing the storage units. [ABSTRACT FROM AUTHOR]

This paper proposes a new policy to calculate the locational marginal price (LMP) in the distribution networks containing distributed generation (DG). The proposed policy is based on remunerating the DG units to reduce the loss and emission of the network. LMP at each DG bus is calculated according to the contribution of the DG to the reduced amount of loss and emission. An iterative algorithm which is based on the nucleolus theory is proposed to allocate the loss and emission reduction. The proposed algorithm will provide a robust state estimation tool for distribution companies (DISCOs) in the next step of operation. The state estimation tool provides the decision maker with the ability to exert its control over private DG units when the loss and emission are minimized. Also, the proposed pricing policy requires decision maker to simply apply its best response strategy to the LMP based on the priority of loss, emission and DISCO's extra benefit. The proposed methodology is applied to two realistic distribution networks, and efficiency and accuracy of the method are verified. [ABSTRACT FROM AUTHOR]

The deployment of the advanced metering infrastructure (AMI) in distribution systems provides an excellent opportunity for load monitoring applications. Load decomposition can be done at the smart meters level, providing a better understanding of the load behavior at near-real-time. In this paper, loads' current and voltage waveforms are processed offline to form a comprehensive library. This library consists of a set of measurements projected onto the eigenloads space. Eigenloads are basically the eigenvectors describing the load signatures space. Similar to human faces, every load has a distinct signature. Each load measurement is transformed into a photo and an efficient face recognition algorithm is applied to the set of photos. A list of all the online devices is always stored and can be accessed at any time. The proposed method can be implemented at the smart meters level. The distributed computation that can be achieved by performing simple calculations at each smart meter, without the need for sending intensive data to a central processor, is beneficial. From a system operator perspective, load composition in near-real-time provides the loads' voltage dependence that are needed, for example, in volt-VAR optimization (VVO) in distribution systems. Further applications of load composition data are also discussed. [ABSTRACT FROM PUBLISHER]

This paper presents a short-term power regulation mechanism for post-segmentation power distribution systems in the presence of severe fault or large disturbance. Firstly, load priority is introduced into system separation and centroids of load clusters are allocated at nodes with distributed sources, respecting power balance and network connectedness. Secondly, fast power flow calculation is performed on the primarily formed islands to resolve load interruption for operational feasibility of partitions from power quality perspective. Then the effect of distributed generation fluctuations on durable operation of subsystems with various optimization objectives is examined. The load response is instructed by the proposed cost-based pricing scheme contemplating consumers' willingness. In addition, the influence of network congestion and load controllability on results of economic scheduling is investigated. Numerical results from the PG&E-69 distribution system are used to show the effectiveness of the developed model in radial structure load clusters. Illustration on the IEEE 118-bus case further proves its robustness and practicability for other distribution systems applications. This property is also useful for transmission switching and micro-grid applications. [ABSTRACT FROM PUBLISHER]

This paper presents the fundamental concepts of a generalized central power management system and a decentralized, robust control strategy for autonomous mode of operation of a microgrid that includes multiple distributed energy resource (DER) units. DER units are divided into voltage-controlled and power-controlled DER units. The frequency of each DER unit is determined by its independent internal oscillator and all oscillators are synchronized by a common time-reference signal based on a global positioning system (GPS). The power management system (PMS) specifies the power and voltage set points for the local controllers of each DER unit. A linear, time-invariant, multivariable, robust, decentralized control system is designed to track the setpoints. Each control agent guarantees fast tracking, zero steady state error, and robust performance despite uncertainties of the microgrid parameters, topology, and the operating point. Existence conditions, control design procedures, eigenanalysis and robust stability analysis of the closed-loop system, and performance of the control strategy based on digital time-domain simulation studies in PSCAD/EMTDC platform, are reported. Performance of the control system is also verified based on hardware-in-the-loop (HIL) studies in the RTDS environment. [ABSTRACT FROM AUTHOR]

This paper presents a new family of universal control and management strategies for microgrids in smart distribution grids. The paper also provides a general and computationally-efficient framework for modeling and analysis of power management strategies in a microgrid with multiple-distributed generation (DG) units which eases microgrid dynamic studies and controller parameters selection in large microgrids with multiple DG units. Three different approaches for real and reactive power management are proposed. The controllers offer the following advantages: 1) the proposed topologies can be applied to both voltage-controlled (VC) and current controlled (CC) voltage source converters (VSCs). 2) The controllers are universal and realize requirements of both grid-connected and islanded modes, i.e., they share real and reactive power during islanding with constant frequency operation and act as grid supporting VSCs in the grid connected mode. 3) The drooping variables can be either power or current, thus VC-power drooping, VC-current drooping and CC-power drooping are different available variants. 4) The concept of hybrid polar-vector control is developed in this paper. Thus, it can combine the benefits of both types of controllers in one augmented strategy. 5) The controller emulates the behavior of conventional synchronous generators (SGs) which in turn results in better integration of electronically-interfaced DG units into the power system and prevents instabilities due to interaction of fast response DGs and SGs. 6) The controllers realize seamless and robust transition to the islanding mode. The controllers are developed under new concept of synchronous converters. A theoretical analysis and simulation results show that the proposed controllers yield the aforementioned requirements in one compact structure. [ABSTRACT FROM PUBLISHER]

Dispersed storage systems (DSSs) can represent an important near-term solution for supporting the operation and control of active distribution networks (ADNs). Indeed, they have the capability to support ADNs by providing ancillary services in addition to energy balance capabilities. Within this context, this paper focuses on the optimal allocation of DSSs in ADNs by defining a multi-objective optimization problem aiming at finding the optimal trade-off between technical and economical goals. In particular, the proposed procedure accounts for: 1) network voltage deviations; 2) feeders/lines congestions; 3) network losses; 4) cost of supplying loads (from external grid or local producers) together with the cost of DSS investment/maintenance; 5) load curtailment; and 6) stochasticity of loads and renewables productions. The DSSs are suitably modeled to consider their ability to support the network by both active and reactive powers. A convex formulation of ac optimal power flow problem is used to define a mixed integer second-order cone programming problem to optimally site and size the DSSs in the network. A test case referring to IEEE 34 bus distribution test feeder is used to demonstrate and discuss the effectiveness of the proposed methodology. [ABSTRACT FROM PUBLISHER]

This paper proposes a multi-timescale coordinated stochastic voltage/var control method for high renewable-penetrated distribution networks. It aims to utilize multiple devices to counteract uncertain voltage fluctuation and deviation. In the hourly timescale (first stage), capacitor banks and transformer tap changers are scheduled before stochastic renewable output and load variations are realized. In the 15-min timescale (second stage), inverters that interface the renewable energy resources provide var support to supplement the first-stage decision after uncertainty is observed. The coordination is model as a two-stage stochastic programming problem with scenario reduction. It is then converted to a deterministic mixed-integer quadratic programming equivalence model and solved by commercial solvers combined. Compared with existing methods, the proposed volt/var control can achieve lower expected energy loss and can sustain a secure voltage level under random load demand and renewable power injection. The proposed method is verified on the IEEE 33-bus distribution network and compared with existing practices. [ABSTRACT FROM PUBLISHER]

In this paper, a flexible optimization-based framework for intentional islanding is presented. The decision is made of which transmission lines to switch in order to split the network while minimizing disruption, the amount of load shed, or grouping coherent generators. The approach uses a piecewise linear model of AC power flow, which allows the voltage and reactive power to be considered directly when designing the islands. Demonstrations on standard test networks show that solution of the problem provides islands that are balanced in real and reactive power, satisfy AC power flow laws, and have a healthy voltage profile. [ABSTRACT FROM PUBLISHER]

Deploying shunt capacitor banks in distribution systems can effectively reduce the power loss and provide additional benefits for system operation. In practice, the power loss on distribution transformers can account for a considerable portion of the overall loss. This paper proposes a method for optimal placement of capacitor banks to the distribution transformers to reduce power loss. The capacitor bank locations are considered at the low-side of transformers. The net present value (NPV) criterion is adopted to evaluate the cost benefit of the capacitor installation project. First, an explicit formula for directly calculating the power loss of radial distribution systems is derived. Then, the optimal capacitor bank placement is formulated as a mixed-integer programming (MIP) model maximizing the NPV of the project subject to certain constraints. The model is suitable for being solved by commercial MIP packages, and the operational control of the capacitor banks to maximize the power loss reduction can be simply achieved by local automatic switching according to VAR measurements. The proposed method has been practically applied in the Macau distribution system, and the simulation results show that the proposed method is computationally efficient, and a considerable positive NPV can be obtained from the optimal capacitor bank placement. [ABSTRACT FROM PUBLISHER]

This paper proposes a distributed control approach to coordinate multiple energy storage units (ESUs) to avoid violation of voltage and thermal constraints, which are some of the main power quality challenges for future distribution networks. ESUs usually are connected to a network through voltage source converters. In this paper, both ESU converters active and reactive power are used to deal with the above mentioned power quality issues. ESUs' reactive power is proposed to be used for voltage support, while the active power is to be utilized in managing network loading. Two typical distribution networks are used to apply the proposed method, and the simulated results are illustrated in this paper to show the effectiveness of this approach. [ABSTRACT FROM PUBLISHER]

The deep interdependence between electrical and gas systems entails a potential threat to the security (or reliability) of both systems. It is imperative to investigate the impacts of massive uncertainties on the overall secure and economical operation of both systems. In this paper, a probabilistic energy flow framework of integrated electrical and gas systems is initially proposed considering correlated varying energy demands and wind power. Three aspects of couplings between electrical and gas systems are considered: gas-fired generators, electric-driven compressors, and energy hubs integrated with power to gas (P2G) units. Furthermore, a multilinear method is specially designed to produce a deterministic energy flow solution for each sample generated by Monte Carlo simulation (MCS). Finally, test results have verified that the proposed multilinear MCS method prevails over the nonlinear MCS. In addition, P2G effectively benefits the operation of both electrical and gas networks. [ABSTRACT FROM AUTHOR]

For the operation of distribution systems, loading balance of distribution feeders is important for reducing power loss and mitigating power flow overloading. In this paper, a loop power controller (LPC) is applied for the control of real power and reactive power flows by adjusting voltage ratio and phase shift so that the loading balance of distribution feeders can be obtained. To incorporate photovoltaic (PV) power generation in feeder loading balance, a Taipower distribution feeder with large PV installation is selected for computer simulation. Daily loading unbalance is determined by analyzing PV power generation recorded by the SCADA system and by constructing daily power load profiles based on distribution automation system (DAS) data. The load transfer required to achieve loading balance and the line impedance of distribution feeders are used to derive the voltage ratio and phase shift of the LPC. Computer simulations indicated that loading balance can be achieved in distribution feeders with large PV system installation by using loop power controllers according to the variation of solar energy and power loading of study feeders. The system power loss reduction resulting from feeder loading balance by LPC is also investigated in this paper. [ABSTRACT FROM PUBLISHER]

This paper presents a new paradigm for distribution system operation in the presence of distributed generation (DG) sources taking into consideration the goodness factor of the DG units. The proposed concept of goodness factor of DG units is based on the computation of the incremental contribution of a DG unit to distribution system losses. The incremental contributions of a DG unit to active and reactive power losses in the distribution system are termed as the active/reactive incremental loss indices (ILI). The goodness factors are integrated directly into the distribution system operations model, which is based on an optimal power flow (OPF) framework. This model seeks to minimize the distribution company's (disco's) energy costs in the short term taking into account the contribution (goodness factor) of each DG unit. Two scenarios are considered in the paper: the first scenario considers the disco to be the owner of the DG units and hence is responsible for their scheduling and dispatch, and the second scenario considers the DG units to be investor-owned. The analysis was carried out considering an 18-bus distribution network extracted from the well-known IEEE 30-bus system and a 69-bus distribution system. [ABSTRACT FROM AUTHOR]

Present-day radial electric power distribution circuit faces multiple challenges due to the increased photovoltaic (PV) generation. This paper aims to examine and design modern distribution circuit topologies for accommodating high PV penetration, while addressing power quality concerns. The central hypothesis of the proposed design approach is that by decreasing the Thevenin impedance at the buses where PVs are connected, the impacts on feeder voltages due to PV generation become less pronounced thereby additional PV capacity can be integrated at the corresponding buses. A novel two-stage optimization framework is proposed. The first stage is a mixed-integer linear programing based formulation to design new optimal configuration for any given distribution circuit. The formulation allows the possibility that the circuit can be operated in either a radial or loop configuration. The second stage, a nonlinear programing based formulation, then finds PV hosting capacity for the identified optimal configuration. The proposed two-stage framework is evaluated for IEEE 123-bus test feeder. It is demonstrated that the PV hosting capacity of the feeder can be increased by 53% by optimally adding two new distribution lines with tie-switches. [ABSTRACT FROM AUTHOR]

Increasing penetration of variable loads and renewable generation will cause the conventional operation strategy of the distribution system to become less certain and effective. This paper presents a method of determining the minimum loss network configuration of a distribution system with uncertain load and renewable generation. A robust optimization model is proposed wherein the optimal decisions on network configurations and losses are derived in two subsequent steps. The first step enforces the radiality constraint before knowing the actual system loads and output level of renewable generation. Power flows are computed next to achieve minimum network losses considering the worst operating conditions over the uncertainty sets. A mixed-integer two-stage robust optimization formulation and a decomposition algorithm in a master-slave structure are proposed to solve the problem. Results of an illustrative example and two test systems are presented to demonstrate the proposed method. [ABSTRACT FROM PUBLISHER]

Integrating renewable energy into the modern power grid requires risk-cognizant dispatch of resources to account for the stochastic availability of renewables. Toward this goal, day-ahead stochastic market clearing with high-penetration wind energy is pursued in this paper based on the DC optimal power flow (OPF). The objective is to minimize the social cost which consists of conventional generation costs, end-user disutility, as well as a risk measure of the system re-dispatching cost. Capitalizing on the conditional value-at-risk (CVaR), the novel model is able to mitigate the potentially high risk of the recourse actions to compensate wind forecast errors. The resulting convex optimization task is tackled via a distribution-free sample average based approximation to bypass the prohibitively complex high-dimensional integration. Furthermore, to cope with possibly large-scale dispatchable loads, a fast distributed solver is developed with guaranteed convergence using the alternating direction method of multipliers (ADMM). Numerical results tested on a modified benchmark system are reported to corroborate the merits of the novel framework and proposed approaches. [ABSTRACT FROM PUBLISHER]

In this paper, an efficient methodology is proposed to deal with segmented-time reconfiguration problem of distribution networks coupled with segmented-time reactive power control of distributed generators. The target is to find the optimal dispatching schedule of all controllable switches and distributed generators' reactive powers in order to minimize comprehensive cost. Corresponding constraints, including voltage profile, maximum allowable daily switching operation numbers (MADSON), reactive power limits, and so on, are considered. The strategy of grouping branches is used to simplify the formulated mathematical problem and a hybrid particle swarm optimization (HPSO) method is presented to search the optimal solution. Fuzzy adaptive inference is integrated into basic HPSO method in order to avoid being trapped in local optima. The proposed fuzzy adaptive inference-based hybrid PSO algorithm (FAHPSO) is implemented in VC++ 6.0 program language. A modified version of the typical 70-node distribution network and several real distribution networks are used to test the performance of the proposed method. Numerical results show that the proposed methodology is an efficient method for comprehensive cost minimization in distribution systems with distributed generators. [ABSTRACT FROM PUBLISHER]

In this paper, we propose a frequency and voltage control strategy for a standalone microgrid with high penetration of intermittent renewable generation systems, which might cause large frequency and voltage deviation in the system due to unpredictable output power fluctuations. To this end, a battery energy storage system (BESS) is suggested for generating the nominal system frequency instead of a synchronous generator, from a frequency control perspective. This makes the system frequency independent of the mechanical inertia of the synchronous generator. However, a BESS has a capacity limitation; a synchronous generator is used to maintain the state of charge (SOC) of the BESS at a certain value. For voltage control, we proposed that a reactive power/active power (Q/P) droop control be added to the conventional reactive power controller. By adding a Q/P droop control, renewable generation acquires a voltage-damping effect, which dramatically alleviates the voltage fluctuation induced by its own output power fluctuation. Simulation results prove the effectiveness of the proposed control strategy from both frequency and voltage control perspectives. [ABSTRACT FROM AUTHOR]

This paper proposes a two-level voltage controller for large-scale power systems. The aim of the controller is to maintain a near-optimal voltage profile in the transmission network by coordinating discrete reactive power (var) control devices in the system. The controller is targeted for implementation in electric power transmission utility companies where most of the voltage controls are coordinated by switching of discrete var devices such as shunt capacitor and reactor banks and transformer banks load tap changers (LTCs). By effectively dividing the controller responsibilities between local substation controls and a central coordinator at control center level, the design is aimed at voltage control of large-scale power systems. At local level, the substation controllers maintain their respective substation bus voltages by local power-flow-like computations using mostly local PMU measurements. The central coordinator computes and provides the voltage set-points to the substation controllers and also coordinates by enabling or disabling the local controllers as needed. The controller is being designed towards prototype implementation in Southern California Edison (SCE), starting with local controllers at specific substations in the first stage. It is tested on real-time dynamic models and large-scale power-flow simulations of SCE transmission network. [ABSTRACT FROM AUTHOR]

The DC power flow model is in widespread utilization in electricity-market applications and contingency analysis. The presented versions of this model can be classified into two categories: state-dependent, or Hot-Start, models and state-independent, or Cold-Start, models. A reasonable accuracy is reported in the literature regarding Hot-Start models as they take into account branch losses and bus voltages by using available base point. On the contrary, due to the absence of base point in Cold-Start models, branch losses must be either neglected or guessed (which is an uncertain precautionary measure), or evaluated by a cumbersome iteration process. In addition, the bus voltage profiles are inevitably considered to be flat. Hence, the accuracy of available Cold-Start models in different circumstances remains of great concern. This paper addresses this concern and unveils a new Cold-Start model that does not rely on a risky assumption. In other words, there will be no lossless or flat voltage profile assumption in the presented approach whereas the equations remain linear. Besides, the exact effect of the net reactive loads on phase angles is considered and, consequently, the reactive power balance equations are reflected in the model for the first time. [ABSTRACT FROM PUBLISHER]

Hierarchically structured automatic voltage control (AVC) architecture has attracted increased interest as networks operate closer to their capacity limits. Hierarchical AVC enables wide-area coordinated voltage regulation (CVR). Due to the inherent complexity of the task, it is based on reduced control models, i.e., simplified models of the system suitable for voltage control. It is a fact however that a single reduced control model (static RCM) cannot be optimal for all network configurations and operating conditions. In pursuit of an improved CVR, this paper investigates the applicability of zoning methodologies in adaptively determined RCM. It further argues that the selection of a zoning methodology affects not only the CVR operation, but also its robustness to erroneous data and proposes a comprehensive generic framework for evaluating its performance. Lastly, it extends and evaluates several zoning-based control model reduction methodologies: namely, hierarchical clustering employing two different proximity metrics, spectral k-way and fuzzy C-means, on both static and adaptive schemes. [ABSTRACT FROM AUTHOR]

Volt/var control (VVC) is one of the primary functions of the distribution management system aiming at optimum operation of power distribution networks while respecting all of their operational and security constraints. However, the recent huge integration of highly stochastic distributed generation (DG) sources with the grid presents a significant challenge to the traditional VVC schemes, which assume the future to be perfectly known. This paper presents a two-stage chance constrained optimization scheme to handle these nodal power uncertainties and guarantees that the operational and security constraints are respected for almost all realizations of the uncertainty. The chance constrained model is solved by collecting enough randomly chosen samples from the probability spaces of the uncertain parameters so that the class of the problem, a mixed integer second-order cone program, is not elevated. The algorithm not only dispatches the optimum schedule for discrete controlling devices like transformers and shunt capacitors but also optimizes the predefined decision rules for reactive power control of DG sources, thus falling in line with the requirement laid down in the revised IEEE 1547 Standard. Numerical simulations on three different test systems show the superiority of the proposed algorithm over the traditional deterministic methods. [ABSTRACT FROM AUTHOR]

Real-time load composition knowledge will dramatically benefit demand-side management (DSM). Previous works disaggregate the load via either intrusive or nonintrusive load monitoring. However, due to the difficulty in accessing all houses via smart meters at all times and the unavailability of frequently measured high-resolution load signatures at bulk supply points, neither is suitable for frequent or widespread application. This paper employs the artificial intelligence (AI) tool to develop a load disaggregation approach for bulk supply points based on the substation rms measurement without relying on smart meter data, customer surveys, or high-resolution load signatures. Monte Carlo simulation is used to generate the training and validation data. Load compositions obtained by the AI tool are compared with the validation data and used for load characteristics estimation and validation. Probabilistic distributions and confidence levels of different confidence intervals for errors of load compositions and load characteristics are also derived. [ABSTRACT FROM PUBLISHER]

In order to optimize their assets, electrical power distribution companies seek out various techniques to improve system operation and its different variables, like voltage levels, active power losses and so on. A few of the tools applied to meet these objectives include reactive power compensation, use of voltage regulators, and network reconfiguration. One target most companies aim at is power loss minimization; one available tool to do this is distribution system reconfiguration. To reconfigure a network in radial power distribution systems means to alter the topology changing the state of a set of switches normally closed (NC) and normally opened (NO). In restructured electrical power business, a company must also consider obtaining a topology as reliable as possible. In most cases, reducing the power losses is no guarantee of improved reliability. This paper presents a multiobjective algorithm to reduce power losses while improving the reliability index using the artificial immune systems technique applying graph theory considerations to improve computational performance and Pareto dominance rules. The proposed algorithm is tested on a sample system, 14-bus test system, and on Administración Nacional de Electricidad (ANDE) real feeder (CBO-01 23-kV feeder). [ABSTRACT FROM PUBLISHER]

The expected impact of distributed generation (DG) into Smart Grid represents a great challenge of the future for power systems. In particular, the integration of DG based on renewable energy sources (RESs) in distribution networks, without compromising the integrity of the grid, requires the development of proper control techniques to allow power delivery to customers in compliance with power quality and reliability standards. This paper proposes a coordinated local control approach that allows distribution system operator (DSO) and independent power producers (IPPs) to obtain benefits offering the voltage regulation ancillary service to DSO and maximizing allowable active power production for each RES unit belonging to the same IPP. The control is based on a cooperation of data transfer between DSO and IPPs. In order to realize such cooperation, a nonlinear constrained optimization problem is formulated and solved by sequential quadratic programming (SQP) method. The validation of the proposed control technique has been conducted through several time series simulations on a real MV Italian distribution system. [ABSTRACT FROM PUBLISHER]

This paper proposes a generic steady-state modeling and power-flow analysis approach for droop- and isochronously controlled microgrids. The proposed framework adopts symmetrical sequence component models, rather than phase-coordinate models, of microgrid elements. Such approach immensely reduces the power-flow execution time, as it breaks down the system model into independent equation sets with considerably reduced sizes. To render the proposed approach practical and generic, it integrates different types and control schemes of distributed generation (DG), including synchronous generator-based DG (SGDG) and electronically interfaced DG units. Furthermore, it incorporates unbalanced loads and feeders, transformer connections, different load characteristics, and configurations, as well as microgrid droop features. A novel power-flow algorithm based on a modified Newton–Raphson method is proposed to solve for the microgrid steady-state voltage magnitudes, angles, and frequency. The accuracy of the models and algorithm is verified through comparison with detailed time-domain simulations in MATALB/Simulink. Additionally, the proposed approach is shown to outperform the reported Newton-Trust Region approach in generality, accuracy, and performance. Two case studies, incorporating IEEE 123-node test microgrid, are further performed to examine the effectiveness of the proposed approach in solving complicated droop-controlled microgrids, and to examine the behavior of droop-controlled DGs in isochronous microgrids. [ABSTRACT FROM AUTHOR]