Search

Miniaturization and low cost contribute to the development and popularization of wireless power transfer (WPT). Reducing the number of power conversion stages can reduce the volume and cost of the WPT converter, and even make it possible to improve the efficiency. A single-stage WPT converter with constant current (CC) and constant voltage (CV) output and its asymmetric modulation method are proposed in this paper. A direct AC-AC converter is applied to the primary side of the WPT converter to directly convert line-frequency AC to high-frequency AC. The applied direct AC-AC converter that can replace the commonly used multi-stage primary converter reduces the number of circuit devices, thereby reducing the volume and cost of primary converter. The proposed WPT converter can realize zero voltage switching (ZVS) and power factor correction (PFC). In order to achieve CC and CV output, a switchable hybrid compensation topology is applied to the proposed WPT converter. A 720-W experimental prototype was manufactured to verify the rationality of the proposed WPT converter and the correctness of the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper proposes a current-fed single-phase inverter without constant intermediate DC link. It eliminates electrolytic capacitor from the DC-link and introduces an intermediate pulsating DC bus. The proposed topology is modular with three full-bridges making it scalable for high-power applications. New pulsating-DC-modulation for back-end pulsating DC-link inverter and secondary modulation (SM) for front-end DC-to-pulsating DC converter is proposed. Soft-switching and device voltage clamping of both primary side and secondary side devices of front-end current-fed full-bridge converter is realized. A rotating partial hybrid pulsewidth modulation has been introduced. One leg of inverter is commutated at a low switching frequency, while the other leg is operated at a high switching frequency for partial period of a line frequency cycle. Thus, switching losses of the back-end inverter are considerably reduced. Rotating mechanism is used to equalize the switching losses of four switches of the inverter. This paper presents detailed operation and analysis of the topology with a proposed modulation scheme. Simulation and experimental results validate the effectiveness and accuracy of the proposed modulation scheme as well as soft-switching and performance of the converter. [ABSTRACT FROM PUBLISHER]

The essential features of a DC–DC converter for fuel cell vehicle are to ensure the higher voltage gain to meet out the higher DC link voltage demand, continuous input current to improve the life span of the fuel cell, presence of common grounding to avoid electromagnetic interference issue and lower voltage stress with reduced components. This paper presents a high voltage gain DC–DC converter by combining the switched capacitor and quasi switched boost network modules. The proposed high voltage gain converter provides the continuous input current, lower voltage stress, utilizes a fewer number of elements and common grounding feature. The operating characteristics, steady-state analysis both in continuous current mode (CCM) and discontinuous current mode (DCM), comparative analysis with contemporary converters are discussed. The theoretical claimed analysis is validated by the simulation and experimental study. The proposed converter is operated for 200 W output power rating and tested for providing the voltage gain in the range of 5–8 times the input voltage gain by varying the input voltage from 25 V–40 V. The efficiency of the proposed converter is also reported for different output power rating which is in the range 91.3%–93.7%. [ABSTRACT FROM AUTHOR]

Most fuel cell electric vehicles require wide voltage-gain DC–DC converters to increase and equalize the relatively low voltage of fuel cell stacks with DC link bus or energy-storage devices, such as supercapacitors or batteries. This paper proposes two new non-isolated DC–DC converters suitable for such applications, which can be extended to other electric vehicles as well. The proposed converters combine the main characteristics of both quadratic Boost and Ćuk converters, offering high step-up voltage and control simplicity using only one ground referenced active power switch. Additionally, the proposed topologies present reduced voltage stress across the active power switch when compared to other boost converters. Considerations about the design of the proposed converters will also be presented. Experimental results obtained using a laboratory prototype validate the effectiveness and feasibility of the proposed topologies and its suitability for fuel cell electric vehicles. [ABSTRACT FROM AUTHOR]

In the rapidly growing field of electrified transportation technology, hybrid electric and electric vehicle (HEV/EV) manufacturers have been placing increasing demands on the designers to improve the efficiency and reduce the costs of vehicle components to sustain a niche in the EV market. To understand the significance and challenges in an efficient and economical drivetrain design, this paper presents a part of an ongoing project that aims at developing a comprehensive study on dc/ac drive motor technology in EV applications. In this paper, a new three-level three-phase matrix converter topology, along with two conventional frequently used three-level three-phase dc/ac converter topologies, namely, diode-clamped and H-bridge converters, are implemented. Furthermore, comprehensive analysis and comparative studies are conducted to examine the performance and efficiency of these converter topologies according to EV design criteria. In addition, experimental investigations are carried out on the aforementioned converter configurations to help EV designers choose the most suitable converter topology. [ABSTRACT FROM PUBLISHER]

The cell voltage imbalance of series-connected energy storage cells, such as supercapacitors (SCs) and lithium-ion cells, causes premature deterioration and a decrease in the available energies of the cells. Various equalization techniques have been developed for diminishing such imbalances. However, since the number of switches, sensors, and/or multiwinding transformers present in conventional equalizers is directly proportional to the number of series connections of the cells, the circuit complexity and cost of the equalizers are prone to increase with the number of series connections. In this paper, single-switch cell voltage equalizers using multistacked buck-boost converters, such as the single-ended primary inductor converter (SEPIC), Zeta, and Ćuk converters, are proposed. These equalizers consist of passive components and a single switch, significantly reducing the complexity of the circuit when compared with that of conventional equalizers. In addition, when the proposed equalizers operate in discontinuous conduction mode, feedback control is not required to limit currents flowing through cells and circuit components. The proposed equalizers are compared with conventional topologies in terms of the number of active and passive components required. Operating analyses were conducted under both cell-voltage-balanced and -imbalanced conditions. Experimental equalization tests were performed for four series-connected SCs using the SEPIC-based single-switch equalizer. The energies of the series-connected SCs were preferentially redistributed by the equalizer to the cell(s) having the lowest voltage, resulting in the elimination of the cell voltage imbalance and subsequent uniformity of the cell voltages. [ABSTRACT FROM PUBLISHER]