Search

Most fuel cell electric vehicles require wide voltage-gain DC–DC converters to increase and equalize the relatively low voltage of fuel cell stacks with DC link bus or energy-storage devices, such as supercapacitors or batteries. This paper proposes two new non-isolated DC–DC converters suitable for such applications, which can be extended to other electric vehicles as well. The proposed converters combine the main characteristics of both quadratic Boost and Ćuk converters, offering high step-up voltage and control simplicity using only one ground referenced active power switch. Additionally, the proposed topologies present reduced voltage stress across the active power switch when compared to other boost converters. Considerations about the design of the proposed converters will also be presented. Experimental results obtained using a laboratory prototype validate the effectiveness and feasibility of the proposed topologies and its suitability for fuel cell electric vehicles. [ABSTRACT FROM AUTHOR]

Ultracapacitor (UC) based dc–dc power supplies are widely used for addressing surge power demands and to provide energy backup to critical loads. The conventional control techniques, such as unified control strategy, though ensure seamless mode transition, do not offer complete flexibility in charging and discharging controls which is crucial in UC-based backup systems. On the other hand, controls, such as independent switch control, though allow great flexibility in control, do not ensure seamless mode transition without appropriate mode-switch logic. This paper proposes a time-varying virtual resistance based mode transition control for independent switch control which not only ensures smooth, seamless transition between charging and discharging control modes but also ensures complete control over the mode transition durations. The proposed control is found to be robust to error mode identification as compared to introducing dead band between control modes. The proposed control is verified on a proof of concept experimental setup at a power level of $P_o=65$ W, voltage level of $V_g=26$ V with the dc–dc converter switching at $f_{\text{sw}}=100$ kHz. The performance comparison with PWM blocking method is also evaluated where the proposed control is found to work well. [ABSTRACT FROM AUTHOR]

A 12-V motor drive system using an onboard battery is promising in vehicle applications, e.g., to rotate an air pump to adjust its air delivery to the burner, thereby providing autonomous exhaust temperature control for the conventional diesel engine vehicle. The 12-V/1-kW motor drive system proposed in this paper consists of a series-resonant LLC MOSFET full-bridge converter, which provides high-efficiency power transfer by implementing zero voltage switching and boosts the dc bus to $\sim$300 V, and an insulated-gate bipolar transistor inverter, which provides the high-side phase currents to a 1-kW/6000-r/min brushless dc motor (BLDC). This design secures the high efficiency, low cost, and low volume. Meanwhile, with the variable output voltage of this dc/dc converter, this paper realizes a commutation torque-ripple reduction method, which will minimize the mechanical vibration. Experimental results on this prototype system demonstrate that: 1) the LLC dc/dc part efficiency is 97.6% with 92% of the inverter efficiency; and 2) the motor commutation torque ripple is reduced close to zero. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel integrated synchronous buck converter for the auxiliary power supply system of electric vehicles, which achieves multiple independently regulated outputs with reduced switching components in comparison with the conventional separate buck converters. In order to obtain a better understanding of the proposed converter, operational principle and performance characteristics of a simplified dual-output buck converter are introduced in detail, as an example. The analysis shows that zero-voltage-switching operation and lower conduction losses could be attained. In addition, its dynamic behavior is similar to the conventional buck converter and thus the controller design is simple. Finally, experimental results based on a prototype circuit in which two inductors are integrated into one magnetic core to achieve further reduced cost are demonstrated to verify the advantages. [ABSTRACT FROM PUBLISHER]

Plug-in hybrid electric vehicles (PHEVs) will play a vital role in future sustainable transportation systems due to their potential in terms of energy security, decreased environmental impact, improved fuel economy, and better performance. Moreover, new regulations have been established to improve the collective gas mileage, cut greenhouse gas emissions, and reduce dependence on foreign oil. This paper primarily focuses on two major thrust areas of PHEVs. First, it introduces a grid-friendly bidirectional alternating current/direct current ac/dc–dc/ac rectifier/inverter for facilitating vehicle-to-grid (V2G) integration of PHEVs. Second, it presents an integrated bidirectional noninverted buck–boost converter that interfaces the energy storage device of the PHEV to the dc link in both grid-connected and driving modes. The proposed bidirectional converter has minimal grid-level disruptions in terms of power factor and total harmonic distortion, with less switching noise. The integrated bidirectional dc/dc converter assists the grid interface converter to track the charge/discharge power of the PHEV battery. In addition, while driving, the dc/dc converter provides a regulated dc link voltage to the motor drive and captures the braking energy during regenerative braking. [ABSTRACT FROM PUBLISHER]