Search

SF6 is a greenhouse gas. Finding an alternative gas for SF6 has become an urgent problem in the switch field. In order to explore the feasibility of replacing SF6 gas with dry air directly, CO2 and C4F7N/CO2 mixed gas, based on the KYN28‐12 medium voltage switchgear, the finite element method was used to solve the three‐dimensional coupled multi‐physics of the switchgear in this paper. From the angle of the temperature field and flow field, the temperature rise characteristics under different operation conditions were analyzed. The results showed that the temperature field and flow field distribution under the four gases were similar. Among them, the temperature rise of SF6 gas was the smallest, followed by the C4F7N/CO2 mixed gas, CO2 and dry air. The flow rate of SF6 gas was the lowest, about 0.11 m/s. The flow velocities of other gases were relatively close. When the switchgear was filled with the same gas, as the inflation pressure increased, the temperature rise of the switchgear decreased and the gas flow rate also dropped to a certain extent. The temperature field and flow field of the switchgear under the C4F7N/CO2 mixed gas at 0.2 Mpa were similar to those under the 0.1 Mpa SF6 gas. Under the C4F7N/CO2 mixed gas, the contact failure of the plum contact made the temperature rise of the switchgear increase overall. The maximum temperature rise point transferred to the contact failure. The temperature rise further rose with the increase of the contact failure degree. The gas flow rate also greatly increased with the failure degree elevated. From the perspective of temperature rise, the C4F7N/CO2 mixed gas has the possibility of being applied in the electrical equipment under the premise of meeting the insulation conditions. © 2022 Institute of Electrical Engineers of Japan. Published by Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]

Gas insulated metal enclosed switchgear (GIS) has been widely used in the world because of its compact structure and adaption to the environment. However, due to frequent operation and other reasons, GIS disconnector is prone to mechanical failure with poor contact, leading to abnormal vibration signals. In this paper, a GIS disconnector contact fault simulation platform is built to collect vibration signals in three states: normal contact, moderate poor contact and severe poor contact of disconnector contact. The Ensemble Empirical Mode Decomposition (EEMD) method is used to decompose the vibration signals, and the IMF decomposition signals are screened by Kurtosis criterion (a numerical statistic method). Finally, the vibration signal features of GIS under different conditions are obtained by reconstructing the screening signals. The results indicate that, under the normal contact, the frequency of GIS vibration signal mainly presents the distribution of 100 Hz and its integer multiple frequency component, when there is a contact defect, the high frequency component in the vibration signal spectrum increases significantly, and the tripling frequency component is present, and the amplitude of component will increase with the severity of the fault. Therefore, this study provides a theoretical reference for on‐line monitoring of GIS disconnecting switch contact fault. © 2021 Institute of Electrical Engineers of Japan. Published by Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]

Vacuum circuit breaker is a kind of power equipment widely used in the power system. It is developing toward the direction of high voltage and high current. How to design the contact to maximize the interrupting capacity of the contact system has been conducted by scholars. In this paper, the magnetic field simulation model of contact system is established, the magnetic field distribution characteristics of vacuum interrupters are studied, and the distribution characteristics of the magnetic field in the half cycle of the cup‐shaped axial magnetic field contact system are simulated and analyzed. On this basis, by changing the contact structure parameters, the effects of the number of slots in the cup, the slot angle, the center hole of the contacts, and the length of the slots on the distribution of the axial magnetic field were obtained. The results show that grooving the contact can reduce the eddy current, but it has a limited effect on reducing residual magnetic field. The increase of slot angle of contact cup can effectively reduce the residual axial magnetic field at the zero current moment and the axial magnetic field intensity at the peak current moment. Based on the above research results, a new embedded axial magnetic contact system with 12 slots embedded magnetic ring and reverse contact cup is designed. The embedded magnetic ring and reverse spiral slot increase the axial magnetic field at the peak current moment and reduce the residual axial magnetic field at the zero current moment. Finally, the characteristics of the magnetic field have been improved significantly compared with the magnetic field of traditional cup‐shaped axial magnetic field contact. © 2020 Institute of Electrical Engineers of Japan. Published by Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]