Search

A new analytic model for calculating of the air‐gap flux density (AGFD) of surface‐mounted permanent magnet synchronous machines (SMPMSMs) is presented. This proposed model is capable to taking into account the effects of magnetic saturation, armature reaction and stator slots opening. Furthermore, the real form of air‐gap distribution and spatial distribution of flux density of the PM poles are considered. The armature reaction effect is modeled using phasor diagram analysis of the motor as a function of the load torque, the armature current amplitude, power factor and the inverse air gap length. Also, saturation phenomenon predicted using the new non‐linear proposed function in connection with the armature reaction effects and the properties of the lamination material. It is shown that the proposed model capable to predicting acceptably the air gap flux density waveform of the SMPMSMs at lagging and leading power factors and with the load torque variation. The presented analytical approach is verified by the two‐dimensional finite‐element analysis (FEA) results. [ABSTRACT FROM AUTHOR]

This study elaborates upon a new modular split‐tooth permanent magnet‐assisted switched reluctance motor (MSTPM‐SRM). In the proposed topology, the stator comprises six modular E‐cores in which the middle poles are split into two teeth. Two permanent magnets (PMs) are placed between each module's middle and side poles. Primarily, the proposed topology is introduced. Next, the principle of operation of the proposed topology are elucidated, and the magnetic equivalent circuit analysis is adopted in order to validate the operational basics. It is proved that the embedded PMs significantly increase the air‐gap's flux density and adjusts the poles' flux density. The flux density distributions, static, and steady‐state characteristics of the proposed MSTPM‐SRM motor and its PMless counterpart are extracted by utilising 2‐D finite element analysis. It is illustrated that the average torque of the proposed MSTPM‐SRM is dramatically increased compared to its PMless counterpart, especially at high excitation currents. Furthermore, the cogging torque analysis is done and it is shown that the proposed structure has approximately zero cogging torque. Finally, a prototyping version of the proposed motor is fabricated, and the experimental results are elicited. It is shown that the experimental results endorse the simulation results. [ABSTRACT FROM AUTHOR]

Wind energy as the cleanest source of renewable energy requires a highly efficient lightweight generator that provides maximum power density while having the least vibration noise and maintenance. In this study, an axial air gap transverse flux machine is presented, and all excitation sources are located in the stator. This structure provides lower core loss, weight and cost due to the full utilisation of the permanent magnets, SMC‐free structure and short magnetic flux path. In fact, by combining the features of a flux‐switching machine into a transverse flux generator with an axial air gap, it is possible to improve the performance of a direct‐drive wind turbine generator by overcoming traditional structures' challenges. To analyse the axial transverse flux switching permanent magnet generator performance characteristics, 3D finite element simulations have been performed, which have been validated by comparing them to the practical results of a single‐phase prototype. The results are in agreement with an acceptable error that is caused by manufacturing uncertainties. [ABSTRACT FROM AUTHOR]

The dual‐excited synchronous condenser (DESC) has two field windings whose axes are located at direct and quadrature axes respectively. The DESC has more capacity of absorbing reactive power than that of the traditional synchronous condenser (TSC). However, the q‐axis field winding distributed on the d‐axis magnetic pole surface can decrease the magnetic circuit area of the rotor core of DESC, thus it may result in the increase of the total harmonic distortion (THD) of the magnetic field and the oversaturation of the rotor magnetic circuit. In order to obtain better electromagnetic characteristics of DESC, a q‐axis field winding structure is proposed by optimising the number of slots, slot pitch and slot dimensions. The influences of the number and pitch of slot in q‐axis on the air‐gap radial flux density and THD of DESC are studied under the d‐, q‐ and dual‐axis excitation modes. The dimensions of the q‐axis slots are optimised by combining the time‐stepping finite element method and Taguchi method, and the optimal structure of q‐axis field winding is obtained. A 10‐kVar DESC is developed to verify the simulation results. This study provides theoretical basis for the design and manufacture of the DESC. [ABSTRACT FROM AUTHOR]