Search

The aim of this article is to develop a rotor reconstruction method for the V‐shaped interior permanent magnet (IPM) machine so that the subdomain method to analytically calculate the air‐gap flux density can be applied. With the proposed method, the V‐shaped IPM rotor with rectangular magnets, magnetic barriers, and saturated iron bridges can be transformed into a U‐shaped equivalent analytical model. The geometry and material parameters of the magnets in the equivalent U‐shaped model can be determined according to the flux equivalence in the air‐gap of the motor. Then using the subdomain method on the U‐shaped equivalent rotor, the static magnetic field problem can be solved and the flux density distribution in the air‐gap be obtained. The validity of this method and accuracy of the solution is verified by the finite element method with case studies. Compared with existing methods, the improved subdomain method has higher accuracy in calculating flux density including radial and tangential components. The presented rotor reconstruction method is not only limited to single‐layer V‐shaped rotor, it can also be applied to other IPM rotors with more complex structures. It is valuable in the design, optimisation of IPM motors, and even development of new rotor topology. [ABSTRACT FROM AUTHOR]

This study elaborates upon a new modular split‐tooth permanent magnet‐assisted switched reluctance motor (MSTPM‐SRM). In the proposed topology, the stator comprises six modular E‐cores in which the middle poles are split into two teeth. Two permanent magnets (PMs) are placed between each module's middle and side poles. Primarily, the proposed topology is introduced. Next, the principle of operation of the proposed topology are elucidated, and the magnetic equivalent circuit analysis is adopted in order to validate the operational basics. It is proved that the embedded PMs significantly increase the air‐gap's flux density and adjusts the poles' flux density. The flux density distributions, static, and steady‐state characteristics of the proposed MSTPM‐SRM motor and its PMless counterpart are extracted by utilising 2‐D finite element analysis. It is illustrated that the average torque of the proposed MSTPM‐SRM is dramatically increased compared to its PMless counterpart, especially at high excitation currents. Furthermore, the cogging torque analysis is done and it is shown that the proposed structure has approximately zero cogging torque. Finally, a prototyping version of the proposed motor is fabricated, and the experimental results are elicited. It is shown that the experimental results endorse the simulation results. [ABSTRACT FROM AUTHOR]

Compared with the single‐stator permanent magnet synchronous motor(SS‐PMSM), the double‐stator permanent magnet synchronous motor(DS‐PMSM) can make full use of the space in the motor cavity to make it have higher torque density, so it is more suitable for direct‐drive occasions with low‐speed and high‐torque. This paper aims to design and compare the parameters and performances of DS‐PMSMs with four different rotor structures: 1)Series magnetic circuit of radial magnetised single‐layer permanent magnet(type Ⅰ), 2)Series magnetic circuit of radial magnetised double‐layer permanent magnet(type Ⅱ), 3)Parallel magnetic circuit of radial magnetised double‐layer permanent magnet(type Ⅲ), 4)Parallel magnetic circuit of tangential magnetised permanent magnet(type Ⅳ). Firstly, the equivalent magnetic circuit method is used to analyse the magnetic circuits of the four DS‐PMSMs. Next, the finite element analysis tool is used to compare the performances of the four DS‐PMSMs with the same volume. Their air‐gap flux density, no‐load back‐EMF, cogging torque, torque characteristics, moment of inertia, rotor loss and efficiency are quantitatively analysed and compared. Finally, this paper provides guidance and suggestions for the selection of the rotor structure of DS‐PMSM. [ABSTRACT FROM AUTHOR]

A Halbach permanent magnet (PM) tubular linear voice coil motor (LVCM) with a semi-closed structure is developed to enhance the thrust density in this study. Generally, the end of conventional LVCM is open and suffers from the considerable end reluctance. The usage of Halbach array in LVCM makes this problem more prominent although it improves the air-gap flux density greatly. The flux at the end of LVCM can be guided to improve the air-gap flux density. Therefore, this study aims to constrain and direct the magnetic field at the end of a Halbach PM LVCM by using a ferromagnetic auxiliary yoke to construct a semi-closed structure. Magnetic equivalent circuit method is utilised to analyse the effect of the auxiliary yoke on air-gap flux density. Besides, finite element analysis is used to analyse the magnetic circuit and design the parameters of LVCM. The semiclosed tubular LVCM topology is manufactured and the effectiveness of this topology is validated by experimental measurements. Results show that the thrust density of LVCM is improved effectively by using an auxiliary yoke at the end. [ABSTRACT FROM AUTHOR]

In this paper, the 117 kW, 60,000 r/min super high-speed permanent magnet generator (SHSPMG) under unbalanced load condition is studied. First, the influence mechanism of the unbalanced load on the generator was revealed, and by using field-circuit coupling method and at rated load, the current unbalance factor (CUF) was determined. Second, through the time-stepping finite element method, the generator air-gap flux was obtained and decomposed in virtue of the principle of Fourier transform. The influence of the unbalanced load on air-gap flux was studied, and the eddy current loss and torque ripple with different CUFs were calculated and analysed. Finally, based on the calculation results of two-dimensional transient electromagnetic field, the negative sequence current was extracted by using the symmetrical component method. The research showed that the harmonic content of air-gap flux density increases when the generator is connected to unbalanced load, and the eddy current loss and the torque ripple increases with the increase of the load unbalance degree. The experimental platform was established and the test data were in good agreement with the model calculated results, which verified the correctness of the model. The research could provide some useful conclusions for the research of the SHSPMG. [ABSTRACT FROM AUTHOR]