Search

Demagnetisation fault (DF) is a common rotor fault in the permanent magnet synchronous motor (PMSM). DF can cause obvious changes in the magnetic field of PMSMs. As a result, previous DF diagnosis methods mainly depends on magnetic field analysis. However, conventional analysis methods based on the magnetic potential‐permeability method, sub‐domain method and magnetic equivalent circuit method are not suitable for DF condition. In addition, DF diagnosis is further complicated by various operating conditions. To address these issues, a robust DF diagnosis method is proposed for PMSM based on d‐axis magnetic network model using magnetic field reconstruction. The proposed fault diagnosis method employs magnetic field reconstruction to obtain the radial air‐gap flux density under the open‐circuit condition. Subsequently, a d‐axis magnetic network is established to solve the demagnetisation coefficient matrix in the DF state. Finally, the effectiveness of the proposed method is validated through simulations and experiments. Both results demonstrate that the proposed method can accurately recognise uniform DF and partial DF with multiple demagnetised permanent magnets, exhibiting great robustness against different operating conditions. [ABSTRACT FROM AUTHOR]

The aim of this article is to develop a rotor reconstruction method for the V‐shaped interior permanent magnet (IPM) machine so that the subdomain method to analytically calculate the air‐gap flux density can be applied. With the proposed method, the V‐shaped IPM rotor with rectangular magnets, magnetic barriers, and saturated iron bridges can be transformed into a U‐shaped equivalent analytical model. The geometry and material parameters of the magnets in the equivalent U‐shaped model can be determined according to the flux equivalence in the air‐gap of the motor. Then using the subdomain method on the U‐shaped equivalent rotor, the static magnetic field problem can be solved and the flux density distribution in the air‐gap be obtained. The validity of this method and accuracy of the solution is verified by the finite element method with case studies. Compared with existing methods, the improved subdomain method has higher accuracy in calculating flux density including radial and tangential components. The presented rotor reconstruction method is not only limited to single‐layer V‐shaped rotor, it can also be applied to other IPM rotors with more complex structures. It is valuable in the design, optimisation of IPM motors, and even development of new rotor topology. [ABSTRACT FROM AUTHOR]

In this article, a hybrid analytical model for a quasi‐regular polygon rotor (QPR) is proposed. It mainly uses the subdomain method and conformal mapping to solve a non‐circular boundary in the QPR. Firstly, the subdomain method combined with an equivalent surface current method is used to calculate the air‐gap magnetic field considering a slotted stator with a circular rotor. Secondly, by segmenting the non‐circular boundary in the QPR, the complex relative air‐gap permeance of the QPR can be calculated using the conformal mapping. Thirdly, this complex relative air‐gap permeance modifies the air‐gap magnetic field calculated in the first step to obtain the actual magnetic field distributions. Consequently, no‐load and loaded air‐gap flux densities, back‐electromotive force and torque can be obtained. A 12‐pole/3‐phase permanent magnet motor is modelled using the proposed hybrid analytical model, which is validated by finite‐element analysis and experiment. This proposed hybrid analytical model presents a new way of processing the QPR. Its calculation speed is nearly 50 times faster than the finite‐element analysis, which is of great help to the initial design and optimisation of machines with QPRs. [ABSTRACT FROM AUTHOR]

Here, a modified magnetic equivalent circuit model which can accurately consider the air‐gap region is presented. The main defect of magnetic equivalent circuit model is in the modelling of air‐gap region. To solve this problem, a new approach based on conformal mappings is presented to accurately calculate the air‐gap permeances between the elements of stator and rotor while considering the real paths of flux tubes in air gap. The distributions of equivalent virtual currents on the both sides of air gap are obtained through modified magnetic equivalent circuit model, which represent the effects of slots, magneto motive force drops in iron parts, and magneto motive force sources. The conformal mapping method is then used to calculate the components of air‐gap magnetic field for every operating point under starting conditions and different loads. One typical cage‐rotor induction motor, which is used in electric submersible pumps, is considered to investigate the accuracy of modified magnetic equivalent circuit model. Some of the analytical results obtained through modified magnetic equivalent circuit model are verified by comparing with the corresponding results obtained from finite element method and experiment set up. [ABSTRACT FROM AUTHOR]

The dual‐excited synchronous condenser (DESC) has two field windings whose axes are located at direct and quadrature axes respectively. The DESC has more capacity of absorbing reactive power than that of the traditional synchronous condenser (TSC). However, the q‐axis field winding distributed on the d‐axis magnetic pole surface can decrease the magnetic circuit area of the rotor core of DESC, thus it may result in the increase of the total harmonic distortion (THD) of the magnetic field and the oversaturation of the rotor magnetic circuit. In order to obtain better electromagnetic characteristics of DESC, a q‐axis field winding structure is proposed by optimising the number of slots, slot pitch and slot dimensions. The influences of the number and pitch of slot in q‐axis on the air‐gap radial flux density and THD of DESC are studied under the d‐, q‐ and dual‐axis excitation modes. The dimensions of the q‐axis slots are optimised by combining the time‐stepping finite element method and Taguchi method, and the optimal structure of q‐axis field winding is obtained. A 10‐kVar DESC is developed to verify the simulation results. This study provides theoretical basis for the design and manufacture of the DESC. [ABSTRACT FROM AUTHOR]

A new type of double‐stator permanent magnet spherical motor (DSSRPMSM) is proposed. Compared with most existing spherical motors, this motor uses a large number of stator iron cores, which can generate larger magnetic flux density and significantly improve torque capacity. The proposed DSSRPMSM can continuously rotate, swing and spiral, and can be used in the multi‐degree‐of‐freedom motion fields of industrial robot joints, moment gyroscopes, panoramic photography tables and so on. Because the motor has the dual characteristics of rotary motor and arc linear motor, the comprehensive effects of stator slotting and stator iron core breaking should be considered. Cylindrical and trapezoidal PM poles are equivalent to dihedral PM poles, and stator coils are equivalent to PM pole models. Analytical models of PM pole magnetic field and stator magnetic field in a spherical coordinate system are established, and the air gap magnetic flux density under unequal magnetic potential boundary conditions is calculated by conformal transformation. The analytical calculation method proposed is consistent with the results of finite element method (FEM) simulation, and the experimental test further verifies the effectiveness and accuracy of this method. [ABSTRACT FROM AUTHOR]

A Halbach permanent magnet (PM) tubular linear voice coil motor (LVCM) with a semi-closed structure is developed to enhance the thrust density in this study. Generally, the end of conventional LVCM is open and suffers from the considerable end reluctance. The usage of Halbach array in LVCM makes this problem more prominent although it improves the air-gap flux density greatly. The flux at the end of LVCM can be guided to improve the air-gap flux density. Therefore, this study aims to constrain and direct the magnetic field at the end of a Halbach PM LVCM by using a ferromagnetic auxiliary yoke to construct a semi-closed structure. Magnetic equivalent circuit method is utilised to analyse the effect of the auxiliary yoke on air-gap flux density. Besides, finite element analysis is used to analyse the magnetic circuit and design the parameters of LVCM. The semiclosed tubular LVCM topology is manufactured and the effectiveness of this topology is validated by experimental measurements. Results show that the thrust density of LVCM is improved effectively by using an auxiliary yoke at the end. [ABSTRACT FROM AUTHOR]

An analytical technique for predicting and optimising the open-circuit magnetic field in brushless surface-mounted permanent magnet (PM) machines with novel two-segment Halbach array has been presented. For the maximum fundamental air-gap flux density, the optimal magnetisation angle has been analytically derived. The effect of the rotor core on the fundamental air-gap flux density in the machine has been investigated. In addition, the proposed analytical technique can also predict the induced back-electromotive force and the electromagnetic torque. The analytical results show that the electromagnetic performance can be significantly improved for the proposed two-segment Halbach array compared with the conventional two-segment Halbach array. Predicted results have been validated by the finite-element analyses for 9-slot/8-pole slotless/slotted brushless PM machines. [ABSTRACT FROM AUTHOR]