Search

Although helical electrodes have been proven to improve the EDM (electrical discharge machining) speed of small holes, there are few studies on the morphological characteristics of the machined small holes and the influence of electrode structures. In this paper, the influence of the helical electrode structure on the machining effect is studied by the method of orthogonal experiment, and the internal mechanism of the influence of the helical electrode on the machining is explained by the method of CFD (computational fluid dynamics) simulation. The results show that the larger depth and width of the helical groove and the helix angle of 60° are beneficial to increase the machining speed and reduce the relative loss rate, and at the same time, avoid serious defects in the small hole morphology. These conclusions provide a valuable reference for future researchers to choose the reasonable structure of the helical electrode, which is of great significance. [ABSTRACT FROM AUTHOR]

This paper presents the manufacture of micro-rotating structure combining micro reciprocated wire electrical discharge machining (wire-EDM) and multi-cutting strategy. A novel rotating spindle is developed to achieve the rotation of cylindrical workpiece and the multi-cutting strategy including rough, semi-finish, and finish machining is attempted to improve the machining removal rate (MRR) and reduce the surface roughness (SR) of micro-rotating structure. To determine proper parameters for multi-cutting process, the effects of machining parameters such as open voltage, discharge capacitance, and rotation rate on MRR and SR are studied by systematically performing experiments planed by single factor design and central composite design (CCD) of response surface methodology (RSM). Analysis of variance (ANOVA) is conducted to identify the significant factor and confirm the adequacy of the established models of MRR and SR. The mathematical models are used to predict MRR and SR within 8.18 and 8.74% prediction error compared with the additivity tests, respectively. Desirability method in RSM technique is used to determine three sets of parametric combinations for multi-cutting process, which are verified by confirmation experiments with 1.75~7.76% prediction error for MRR and 2.77~8.59% prediction error for SR. Finally, a typical microballoon probe is successfully machined with 0.435 Ra and 98.7-μm diameter by the proposed method, which provides a feasible approach for the fabrication of micro-rotating structure with high efficiency and smooth surface. [ABSTRACT FROM AUTHOR]

Wire electric discharge machining (WEDM) and electrical discharge machining (EDM) promise to be effective and economical methods for the machining of metal matrix composites and conducting ceramic blanks. However, the machining process of Ni-AlO functionally graded materials (FGMs) is extremely difficult because the insulating ceramic layer cannot be machined directly by EDM. In this paper, the pure AlO layer has been machined by self-induced EDM, using the conductive layers of Ni-AlO FGMs to trigger the discharges in the insulating ceramic layer. Machining experiments have been performed to investigate the effects of discharge capacitance, pulse off-time, and charging resistance on the process performance of the pure AlO layer using RC-type pulse generator. From the experimental results, the discharge waveform of pure AlO layer includes long pulse discharge waveform, in addition to conventional normal discharge of conductive layers. The shape of long pulse discharge waveform can be changed by pulse off-time. The appropriate pulse off-time not only improves the stability of EDM but also increases the material removal rate (MRR). Moreover, it was observed that the MRR increases with increasing discharge capacitance and decreasing charging resistance. The surface roughness increases with increasing discharge capacitance. Finally, a small hole with a depth-diameter ratio of 5, little tapper is machined based on the experimental analysis. [ABSTRACT FROM AUTHOR]

Ni-AlO functionally graded materials (FGMs) have become important for high-temperature applications due to a continuous change in composition. However, the manufacturing of Ni-AlO FGMs with conventional machining methods is a long and costly process because of the insulating ceramic composition. This paper presents a new method of machining Ni-AlO FGMs by self-induced electrical discharge machining (EDM). Self-induced EDM uses the conductive compositions of Ni-AlO FGMs to trigger the discharges in the insulating composition. Machining characteristics of a four-layered Ni-AlO FGMs drilled by self-induced EDM have been investigated, which include the material removal mechanisms, discharge properties, surface characteristics, material removal rate, and electrode wear ratio. It has been found that graded layers, 70 % Ni-graded layer and 30 % Ni-graded layer, are removed by dislodgement of AlO particles, in addition to conventional melting and evaporation. Pure AlO layer is melted and evaporated by utilizing conductive layer-induced discharges. The discharge properties, surface characteristics, material removal rate, and electrode wear ratio are significantly influenced by the material removal mechanisms of graded compositions. These findings demonstrate that self-induced EDM is able to effectively machine Ni-AlO FGMs. [ABSTRACT FROM AUTHOR]