Search

Summary: Multilevel inverters have many applications, such as the grid integration of photovoltaic cells, FACTSs devices, electric vehicles, variable speed drives, and smart grids. In this paper, a new bidirectional diode‐based unit is proposed for a symmetric single‐phase modular inverter topology that can achieve high output levels by using a small number of switching and circuit devices. The basic structure can generate nine‐level voltage with only nine IGBTs and two diodes. Another advantage of the proposed topology is the utilization of a half‐bridge module to change the voltage polarity and the low number of its voltage sources. Additionally, the proposed topology can be used as the cascaded structure with different approaches to select the value of voltage sources. The power losses are discussed for the proposed basic module. A comparison has been made with some recently presented topologies to compare the proposed multilevel inverter and demonstrate its superiority. The comparison is performed for the basic module and its generalized structure. In this paper, the pulse width modulation technique is utilized to achieve a voltage waveform with low harmonic content. The proposed basic structure has an efficiency of 58.98% in 5KW power. Finally, the operation of the proposed basic module is simulated, and the laboratory prototype results confirm the accuracy of the simulation results. [ABSTRACT FROM AUTHOR]

In this paper, a new transformerless buck–boost converter is proposed. This converter is based on combining two basic converters, including Cuk and traditional buck–boost converters, along with a voltage multiplier (VM) at the output side. The proposed semi‐quadratic buck–boost converter operates in continuous conduction mode (CCM) and provides two operation modes by turning the switches on and off. This converter has some merits such as a wide conversion ratio and continuous input current. The proposed converter consists of two switches with simultaneous operation resulting in simplicity in control. A modular configuration and a wide range of duty cycles are available through the proposed converter, which causes higher or lower output voltage and facilitates the converter maintenance. The calculations of the ideal and the real voltage gain, voltage stress of switches and diodes, efficiency, and design consideration of elements are given in this paper. Finally, a prototype is implemented, and experimental waveforms are obtained to prove and validate the simulation results as well as the theoretical analysis of the proposed converter. [ABSTRACT FROM AUTHOR]

To meet the higher DC link voltage requirement in distributed energy resources (DERs) such as fuel cells (FCs), wind turbines (WTs), and photovoltaic (PV) systems, DC–DC converters are applied. A voltage‐lift (VL) circuit‐based transformer‐less active switched LC‐network (ASLC) converter with a high‐voltage gain is proposed in this paper. Compared to a similar reference converter, the voltage gain of the proposed converter increases efficiently by adding one extra capacitor and diode. The operation of the converter in continuous current mode (CCM) and discontinuous current mode (DCM), the analysis of the steady‐state condition, and comparative analysis with some similar converters are discussed. Moreover, the parasitic elements are assumed to calculate the DC‐voltage gain and the efficiency of the converter accurately. The performance of the proposed step‐up converter is simulated in the PSIM software. A prototype circuit rating of about 20/280 V, 200 W of converter model is designed, and its performance is validated. The experimental outcomes clarify the feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

Multi‐level inverters (MLIs) for medium or high power and voltage utilization have acceptable application in industry and are utilized commercially. The performance of MLIs is considerably preferable to traditional two‐level inverters due to their negligible harmonic content, small filter size, utilization of lower‐rated voltage devices, low electromagnetic interference (EMI), and so on. However, in the face of these many advantages, few disadvantages can be expressed such as more device count and a sophisticated control strategy. This paper presents an improved switched‐ladder topology to enhance the performance of multi‐level inverters by improving the above drawbacks. Compared to existing inverter topologies, the proposed extendable diode‐containing bidirectional structure requires fewer switches and driver circuits. The proposed topology is compared with other similar topologies, and its superiority is examined. Fundamental switching frequency modulation technique is utilized to obtain high‐quality output voltage waveforms with lower harmonic contents and reduced switching losses. This converter, despite the use of diodes, can supply the low power factor inductive‐resistive loads, bidirectionally. To demonstrate the performance of the proposed topology, in addition to simulation with the nearest level modulation technique, a prototype of the proposed structure has been implemented and tested. The results display the proper performance of the proposed topology in the real‐time environment. [ABSTRACT FROM AUTHOR]

Multilevel inverters (MLIs) have made great strides in utilizing renewable energy and industrial applications compared to conventional two‐level inverters in terms of output voltage quality, smaller size of the output filter, and higher efficiency. This paper describes a new diode containing bidirectional topology for single‐phase MLI. This structure is presented to reduce the count of switches, isolated voltage sources, and drivers that can increase the number of output levels modularly. This converter, despite the use of diodes, can feed bidirectionally the low power factor inductive–resistive loads. The proposed structure has been designed to achieve a higher output voltage levels relative to the number of switches, drivers, and direct current (DC) voltage sources. Three different algorithms have been proposed to determine the values of DC voltage sources. To confirm the superiority of the proposed structure, a detailed comparison has been carried out with other MLI topologies. Then the proposed topology is simulated in Matlab/Simulink environment using the nearest level modulation technique. Finally, experimental results are presented to confirm the performance of the designed structure in symmetric and asymmetric topologies. [ABSTRACT FROM AUTHOR]

Summary: In this paper, a bidirectional diode containing multilevel inverter is introduced to reduce the number of switching elements especially in the case of a high number of output voltage levels. In comparison with classic and recently introduced symmetrical topologies, which are trying to reduce the switch count, this topology has a lower number of semiconductor switches in the same number of output voltage levels. This makes the proposed inverter to be a suitable choice for medium voltage applications like renewable energy applications as well as medium voltage electric drives. Moreover, it can be used in a cascaded configuration for high voltage levels. To depict the performance of the proposed structure, a comprehensive comparison is made between this topology and classic and recently proposed symmetric topologies in terms of switch and gate driver count, power losses, and cost. The performance of the proposed symmetrical 11‐level converter is analyzed and simulated in MATLAB/Simulink for both PWM and selective harmonic elimination switching methods. Not only the results are desirable but also the experimental results of laboratory prototype validate the simulation results. [ABSTRACT FROM AUTHOR]

Summary Multilevel inverters are known as essential converters in renewable sources. First, in this paper, a new submodule is presented, and based on it, a new sub‐multilevel inverter is presented. The proposed sub‐multilevel inverter consists of several unidirectional and bidirectional switches and DC voltage sources. Then, the generalized topology, developed in two modular and cascaded modes, is presented to increase production levels. The proposed submodules are connected in series in the modular topology, increasing production levels. The proposed topology to produce the maximum output levels has the minimum number of IGBTs, drivers, DC voltage sources, etc. Mathematical analyses for conduction and switching losses are provided, and mathematical analyses for the number of devices and voltage across the switches are also presented. In addition to the mathematical analysis of losses, the simulation results are also presented. A general comparison of proposed topology components is presented to demonstrate their advantages. This comparison shows that the proposed topology has the minimum number of power electronic devices. In this paper, nearest level modulation is used to control the proposed topology. The simulation and experimental results of the proposed sub‐multilevel verify the performance of the proposed topology. [ABSTRACT FROM AUTHOR]