Search

The transient response of heat exchangers plays a significant role in the time-dependent performance of thermal management systems, particularly in resource-limited situations with high power density and fast-acting heat sources. A scaled thermal management testbed with a plate-frame heat exchanger was built to emulate a thermal subsystem. This paper describes a methodology for dynamically characterizing the behavior of a commercial, off-the-shelf plate-frame heat exchanger both experimentally and computationally. Statistical design of experiments principles was used to develop a test plan composed of 20 test cases for dynamic model validation. The dynamic performance of the heat exchanger was evaluated with a physics-based model, and statistical surrogate models were derived from the experimental results. Additionally, a lumped mass model was employed to determine the dynamic parameters of the heat exchanger using the experimental data. The model efficiently and accurately predicts the experimental results across the entire experimental exploration space. The lumped mass model predicts the transient response without using computationally expensive resources such as a full numerical, thermo-fluid dynamic solvers. This approach has significant implications for developing practical models of thermal components particularly for the field of thermal controls. [ABSTRACT FROM AUTHOR]

• The desirable operating conditions to achieve high operational efficiency are obtained. • The performance of the IEC under different operating conditions is investigated. • The mathematical model is validated against published data. • The optimal dimensions that give good efficiency in climates with moderate humidity are highlighted. [Display omitted] This paper presents a study investigating and analyzing the effect of heat and mass exchanger (HMX) dimensions and the flow parameters on the indirect evaporative cooler (IEC) system's performance. For this purpose, a mathematical model based on heat and mass transfer concepts was developed, and the model was verified using experimental and simulation results from published papers. Simulations were performed based on different operating and structural conditions affecting the outlet air temperature, cooling capacity, coefficient of performance, and wet-bulb efficiency. Results showed that the optimal dimensions that give good efficiency in climates with moderate humidity, the length of the duct should be between 0.6 to 1.0 m , the width of the channel between 0.3 to 0.5 m , and the channel gap between 0.004 to 0.008 m. It has also been observed that the increasing working air velocity has a positive effect on cooling performance, and its velocity should not be less than 1 m / s. As for increasing the product air velocity, it reduces the heat exchange period, which is undesirable, so it should not exceed 1 m / s. The prescribed flow rate ratio between product and working air should be 0.3 to 0.5. This analysis provides desirable operating conditions to achieve high operational efficiency as well as optimal dimensions for designing such a cooler. [ABSTRACT FROM AUTHOR]

• The mathematical model is useful for analyzing the heat exchanger performance. • The most probable variant of heat exchanger operation is established. • There is a risk of frost accumulation within the fixed-bed regenerator. The paper describes an original mathematical model of heat and mass transfer for a fixed bed regenerator used to determine the effect of internal airflow leakage on heat exchanger efficiency. First, the build and operating principles of a fixed-bed heat exchanger were discussed. The presence of internal leakage was shown along with a proposed solution for its elimination. Then, a mathematical model based on a modified ε-NTU method for numerical simulation and analysis of coupled heat and mass transfer in a fixed-bed heat exchanger was presented. The model was supplemented with an additional detailed submodel designed to determine frost surface temperature and frost growth analysis. Initial numerical simulations of the operation of the model were performed for low outdoor air temperature conditions. Different zones of heat and mass transfer within the regenerator matrix were distinguished. The presence of accumulated frost area and its influence on the course of heat and mass transfer processes was revealed. In addition, the presence of a relative humidity limit curve associated with a mass balance deficiency conditioning the occurrence of frost accumulation was established. [ABSTRACT FROM AUTHOR]

This paper presents a numerical study of heat and mass transfer in indirect evaporative air coolers with four air flow patterns: parallel-flow, counter-flow, cross-flow and regenerative. The numerical simulation was performed on the basis of original two-dimensional heat and mass transfer models (in the case of cross-flow heat exchanger the model was 3D). The mathematical models developed were validated against published experimental data presented in Appendix A . It was established, that heat and mass transfer processes in the wet channels of counter-flow, cross-flow and regenerative indirect evaporative coolers are characterized by creation of two particular heat and mass transfer zones. Detail analysis of the temperature and humidity ratio distributions and boundary conditions, characterizing the coupled heat and mass transfer process in each of these determined zones, revels the violation of the Lewis relation unity under a certain inlet and operation conditions. A theoretical method for estimating the Lewis factor was proposed. Using the developed models the thermal performances of the conventional designs of indirect evaporative air coolers were analyzed numerically and preferable climatic zones for considered heat exchanger were established. Four novel heat exchangers utilizing the advantages of the basic cycles heat exchangers were presented. [ABSTRACT FROM AUTHOR]

This paper investigates a mathematical simulation of the heat and mass transfer in the two different Maisotsenko Cycle (M-Cycle) heat and mass exchangers used for the indirect evaporative cooling in different air-conditioning systems. A two-dimensional heat and mass transfer model is developed to perform the thermal calculations of the indirect evaporative cooling process, thus quantifying the overall heat exchangers’ performance. The mathematical model was validated against the experimental data. Numerical simulations reveal many unique features of the considered units, enabling an accurate prediction of their performance. Results of the model allow for comparison of the two types of heat exchangers in different applications for air conditioning systems in order to obtain optimal efficiency. [ABSTRACT FROM AUTHOR]