Search

Abstract: This paper describes the application of exergy analysis to human heat and mass exchange with the indoor environment. The basis for this paper is the existence of a formal similarity between the parameters defining human heat and mass transfer governed by physiological processes and the parameters defining exergy destruction. Basic heat and mass transfer is calculated using a standard two-node human physiological model. To enable an exergy analysis the model was divided according to heat and mass transfer over appropriate boundaries. The exergy analysis was performed for each process with regard to the type of exergy that participates in heat and mass exchange with respect to the indoor environment. The results provide insight into the complex interactions between the human body and environment as characterized by exergy destruction. Furthermore, the analysis indicates that at given physiological parameters only a certain combination of environmental conditions ensures minimal exergy destruction. These environmental and human conditions coincide with expected level of thermal comfort. [ABSTRACT FROM AUTHOR]

Abstract: Enthalpy exchangers have been used as an efficient means to recover both sensible heat and moisture from exhaust ventilation air. A cross-flow plate-fin structure is the most popular arrangement for the exchanger core due to its compactness and high mechanical strength even with very small channel wall thickness. Traditionally, hygroscopic paper is selected as the plate and fin materials. Though the sensible effectiveness with this material is satisfactorily high, the latent effectiveness is disappointingly low due to the low moisture diffusivity in paper. To solve this problem, in this study, a novel concept is proposed to augment moisture transfer in the exchanger. Plates and fins are made with different materials. A novel membrane – the composite supported liquid membrane (CSLM) is used as the plate material. Paper is still used as the fin material for its cheapness and high support strength. To make comparisons, two cores, one is paper-fin and paper-plate, and another one is paper-fin and membrane-plate, are constructed and tested for heat and moisture recovery. Simultaneous heat and moisture transfer in the plate-fin core is studied. Mathematical model governing the heat and moisture transfer in the cores is set up and numerically solved. Both the experimental data and numerical results indicate that the latent effectiveness of the paper-fin and membrane-plate core is 60% higher than the traditional paper-fin and paper-plate core, due to the high moisture diffusivity in the CSLM. [Copyright &y& Elsevier]

• The desirable operating conditions to achieve high operational efficiency are obtained. • The performance of the IEC under different operating conditions is investigated. • The mathematical model is validated against published data. • The optimal dimensions that give good efficiency in climates with moderate humidity are highlighted. [Display omitted] This paper presents a study investigating and analyzing the effect of heat and mass exchanger (HMX) dimensions and the flow parameters on the indirect evaporative cooler (IEC) system's performance. For this purpose, a mathematical model based on heat and mass transfer concepts was developed, and the model was verified using experimental and simulation results from published papers. Simulations were performed based on different operating and structural conditions affecting the outlet air temperature, cooling capacity, coefficient of performance, and wet-bulb efficiency. Results showed that the optimal dimensions that give good efficiency in climates with moderate humidity, the length of the duct should be between 0.6 to 1.0 m , the width of the channel between 0.3 to 0.5 m , and the channel gap between 0.004 to 0.008 m. It has also been observed that the increasing working air velocity has a positive effect on cooling performance, and its velocity should not be less than 1 m / s. As for increasing the product air velocity, it reduces the heat exchange period, which is undesirable, so it should not exceed 1 m / s. The prescribed flow rate ratio between product and working air should be 0.3 to 0.5. This analysis provides desirable operating conditions to achieve high operational efficiency as well as optimal dimensions for designing such a cooler. [ABSTRACT FROM AUTHOR]

This paper presents a numerical study of heat and mass transfer in indirect evaporative air coolers with four air flow patterns: parallel-flow, counter-flow, cross-flow and regenerative. The numerical simulation was performed on the basis of original two-dimensional heat and mass transfer models (in the case of cross-flow heat exchanger the model was 3D). The mathematical models developed were validated against published experimental data presented in Appendix A . It was established, that heat and mass transfer processes in the wet channels of counter-flow, cross-flow and regenerative indirect evaporative coolers are characterized by creation of two particular heat and mass transfer zones. Detail analysis of the temperature and humidity ratio distributions and boundary conditions, characterizing the coupled heat and mass transfer process in each of these determined zones, revels the violation of the Lewis relation unity under a certain inlet and operation conditions. A theoretical method for estimating the Lewis factor was proposed. Using the developed models the thermal performances of the conventional designs of indirect evaporative air coolers were analyzed numerically and preferable climatic zones for considered heat exchanger were established. Four novel heat exchangers utilizing the advantages of the basic cycles heat exchangers were presented. [ABSTRACT FROM AUTHOR]

This paper investigates a mathematical simulation of the heat and mass transfer in the two different Maisotsenko Cycle (M-Cycle) heat and mass exchangers used for the indirect evaporative cooling in different air-conditioning systems. A two-dimensional heat and mass transfer model is developed to perform the thermal calculations of the indirect evaporative cooling process, thus quantifying the overall heat exchangers’ performance. The mathematical model was validated against the experimental data. Numerical simulations reveal many unique features of the considered units, enabling an accurate prediction of their performance. Results of the model allow for comparison of the two types of heat exchangers in different applications for air conditioning systems in order to obtain optimal efficiency. [ABSTRACT FROM AUTHOR]

Abstract: This paper presents a heat and mass transfer simulation of an adsorber, taking into consideration the geometry of the heat exchanger and the diffusion in the adsorbent medium. In this model, an increment in the direction of heating/cooling fluid containing one (or more) fin pitch was considered. In the domain of this increment, the distribution of the adsorbent temperature was evaluated in the radial and axial directions. The model is validated by experimental data of different adsorbents, volume flows and temperatures. All data were collected in an adsorber test-bench at Fraunhofer ISE. As a result it was found a coefficient of multiple determination of around 0.94 and an error of 20% during the transient. Finally, the model was run on typical operation for cooling application and compared with data from literature. A numerical energy balance was also evaluated. In summary, the results obtained by a independent group shows the same range of confidence of the model developed here, in terms of the tendency of the curves and even the absolute values. [Copyright &y& Elsevier]

Abstract: In the paper, numerical and experimental analyses of heat and mass transfer during frost formation on a fin-and-tube heat exchanger have been presented. Modelling of the frost formation on cold surfaces placed in a humid air stream, requires a complex mathematical approach. A transient two-dimensional mathematical model of frost formation has been developed. The applied mathematical model has been defined using governing equations for the boundary layer that include air and frost sub-domains as well as a boundary condition on the air–frost interface. The mathematical model with initial and boundary conditions has been discretised according to the finite volume method and solved numerically using the SIMPLER algorithm for the velocity–pressure coupling. Results have shown that the frost layer formation significantly influences the heat transfer between air and fins. As a result of numerical calculations, time-wise frost thickness variations for different air humidities, temperatures and velocities have been presented. Using the developed mathematical model, the algorithm and the computer code, which have been experimentally validated, it is possible to predict a decrease of exchanged heat flux in the heat exchanger under frost growth conditions. [Copyright &y& Elsevier]

Abstract: The paper presents the geometry of infinite regular polyhedrons that can be used to construct the heat exchange units. The basic structural component of the infinite solid consists of six hexagons, which meet in the common vertex. The mathematical model of heat and mass transfer inside the labyrinth heat exchanger is shown. The first and the second Kirchhoff’s laws are used to simulate fluid flow distribution at hydraulic network created with connected basic solids. Heat balance equations are adopted to describe forced convection heat transfer inside developed heat exchanger. Good accordance among the experimental data and calculation results over whole simulation range is obtained. The efficiency and thermal characteristic of the labyrinth heat exchanger is presented in the form of graphs. [Copyright &y& Elsevier]