Search

In this study, an experimental investigation is conducted to study the effects of CO addition (0%–7.5% vol.) on the self-ignition of pressurized hydrogen leakage. The result shows that more CO addition significantly decreases the likelihood of self-ignition inside the tube and the formation of self-sustained jet flame outside the tube. This can be mostly explained by the reduction of leading shock intensity inside the tube. Furthermore, CO addition effectively inhibits the flame propagation and development inside the tube. For pure hydrogen, the ignited flame quickly develops an intense flame spanning the tube width and eventually form a jet flame in ambient air. However, the H 2 –CO diffusion flame initiated approaching tube sidewall tends to propagate adjacent to the wall or be soon quenched with more CO addition. If the CO-weakened flame spouts to the tube exit, it may not survive the expansion at the tube exit and thus it is quenched. • The shock intensity is reduced in the presence of CO. • The critical pressure for self-ignition increases with CO addition concentration. • Shock intensity variation by CO addition is the main factor affecting self-ignition onset. • Small CO addition can effectively inhibit flame development inside the tube. • H 2 –CO flame spouting from the tube exit tends to be blown out. [ABSTRACT FROM AUTHOR]

This paper demonstrates experimental investigation on the self-ignition and subsequent flame propagation of high-pressure hydrogen-methane mixture release via a tube. The proportion of methane added to hydrogen is 2.5% (vol.). A transparent rectangular tube (d = 15 mm, L = 400 mm) is used in the experiments. It is shown that the minimum burst pressure required for self-ignition increases 1.57 times for only 2.5% methane addition from 2.89 MPa (pure hydrogen) up to 4.68 MPa (2.5% CH 4 addition). This is mainly caused by the following reasons: on the one hand, methane addition can result in the decease of shock intensity inside the tube, thereby lowering the temperature of the combustible mixture; on the other hand, the hydrogen-methane mixture has the higher minimum ignition energy than that of pure hydrogen. Besides, 2.5% methane addition can increase the initial ignition time, weaken the flame intensity and reduce the flame propagation velocity relative to tube wall inside the tube. Moreover, for cases with 2.5% methane addition, the complete flame throughout the tube is formed closer to the back end of the tube. When the self-sustained flame exits from the tube, the maximum overpressure in a confined space increases with 2.5% methane addition. • The effect of 2.5% methane addition to hydrogen is experimentally investigated. • The shock wave intensity is reduced in the presence of the methane. • The addition of methane can decrease the possibility of hydrogen self-ignition. • Initial ignition occurs in the tube wall and then develops into a complete flame. • The hydrogen-methane mixture brings greater combustion overpressure in chamber. [ABSTRACT FROM AUTHOR]

The shock wave dynamics, spontaneous ignition and flame variation during high-pressure hydrogen release through tubes with different cross-section shapes are experimentally studied. Tubes with square, pentagon and circular cross-section shapes are considered in the experiments. The experimental results show that the cross-section shape of the tube has no great difference on the minimum burst pressure for spontaneous ignition in our tests. In the three tubes with length of 300 mm, spontaneous ignition may occur when overpressure of shock wave is 0.9 MPa. When the spontaneous ignition is induced in a non-circular cross-section tube, the possible turbulent flow in the corner of the tube increases can promote the mixing of hydrogen and air, thus producing more amount of the hydrogen/air mixture. As a result, both the peak light signal and flame duration detected in the non-circular cross-section tubes are more intense than those in the circular tube. The smaller angle of the corner leads to a more intensity flame inside tube. When the hydrogen flame propagates to the tube exit from the circular tube, the ball-like flame developed near tube exit is relatively weak. In addition, second flame separation outside the tube is observed for the cases of non-circular cross-section tubes. • The effect of cross-section shapes of tube has been experimentally investigated. • The use of burst disk with cross notching on surface exhibits good repeatability. • The ignition occurs when the overpressure of shock wave is about 0.9 MPa. • The cross-section shape shows a significant influence on the flame intensity. • Twice flame separation are observed for cases of non-circular cross-section tubes. [ABSTRACT FROM AUTHOR]

Due to the high probability of hydrogen leaking from narrow cracks of the vessels, an experimental study is conducted to investigate the spontaneous ignition of high-pressure hydrogen released into a tube through inlets with different narrowness, including circular, square (length-width ratio χ = 1), and two slit shapes of χ = 2 and 3, with the same area. Pressure transducers and photoelectric sensors are used to detect shock wave dynamic variation and ignition occurrence. The results indicate that narrow inlets weaken the shock wave intensity and speed, and the weakening effect increases with narrowness. Moreover, spontaneous ignition is affected. The minimum burst pressure required for spontaneous ignition is higher in the cases with square and slit inlets. Most significantly, when χ is 3 , it is 2.5 times that of circular inlet. Meanwhile, for narrow inlets, the ignition flame intensity and speed are enhanced, and the inlet of χ = 2 has the greatest impact. • The influence of narrow releasing ports on self-ignition hydrogen is investigated. • Narrow ports weaken the shock wave intensity and speed. • It requires higher burst pressure for self-ignition under narrow ports. • The flame intensity is enhanced under narrow ports. • Different narrowness of the ports brings different effects. [ABSTRACT FROM AUTHOR]

Experiments on shock waves propagation, spontaneous ignition, and flame development during high-pressure hydrogen release through tubes with symmetrical obstacles (O 1-1) and asymmetrical obstacles (O 1-2) are conducted. The obstacle's side is triangular with a length of 4 mm, a height of 3.6 mm, and its width is 15 mm. In the experiments, a reflected shock wave generates and propagates both upstream and downstream when the leading shock wave encounters the obstacle. At the same burst pressure, the reflected shock wave intensity in tube O 1-1 is significantly greater than that in tube O 1-2. Moreover, the presence of obstacles in the tube can induce spontaneous ignition. The minimum burst pressures for spontaneous ignition for tubes O 1-1 and O 1-2 are 2.84 MPa and 3.28 MPa respectively, lower than that for the smooth tube. Furthermore, both the initial ignition position and ignition time are greatly advanced in obstruction tubes, mainly affected by obstacle positions and burst pressures. Finally, the flame separation process near the obstacle is observed. After passing the obstacle, the flames grow rapidly in radial and axial directions on the tube sidewalls. And at the same burst pressure, the flame convergence time in tube O 1-2 is usually longer than that in tube O 1-1. • The influence of obstacles arrangements on self-ignition hydrogen is investigated. • Reflected shock wave forms and propagates both upstream and downstream. • The presence of the obstacles can facilitate the occurrence of self-ignition. • Obstacles arrangements have great effects on ignition positions and ignition time. • The flame separation is observed inside both obstruction tubes. [ABSTRACT FROM AUTHOR]