Search

• A steady cone-jet occurs in a greater range of liquid flow rates for a hemispherical capillary. • Varicose and whipping regimes are easily obtained with a hemispherical nozzle. • The transition from varicose and whipping usually depends on interfacial forces on the jet. • A general parameter to determine varicose, transition, and whipping regimes is presented. A cone-jet regime in electrohydrodynamic atomization (EHDA) is widely applied into printing, electro-spinning, spray-coating, and biological mass spectrometry. Regulating different instabilities of jet is crucial for optimizing its operating parameters. In present work, an atypical, hemispherical capillary with inner diameter of 0.40 mm and cap size of 6.20 mm was employed as atomization nozzle, through which a steady cone-jet regime was confirmed versus suitable feeding liquid flow rate and electric potential. A permanent and highly charged jet emits from a Taylor cone apex and further disintegrates into fine highly charged drops in the form of varicose or whipping instabilities. The results indicate that a steady cone-jet is observed in the specific ranges of the feeding liquid flow rate, electric potential and conductivity. The typical breakup instabilities including varicose and whipping are clearly observed with an increase in liquid flow rate for a fixed electric potential for most of liquids, and the transition from varicose to whipping instability easily occurs. For a steady cone-jet, the jet breakup instabilities usually depends on the competition between interfacial forces on the electrified jet. The transition process involving a low-viscosity jet with a large flow rate is observed, and the general parameter G = Γ 2 δ μ 0.52 is calculated to account for surface charge, surface tension, and viscosity effects, where Γ is the electric force to surface tension ratio and δ μ is the inertia to viscous force ratio. Finally, the varicose, transition regime, and whipping are classified with first and second critical threshold values G = 40 and G = 102, respectively. Meanwhile, as the electrified jet transforms from varicose to whipping instabilities, the jet breakup length shows a trend of increasing first and then decreasing. [ABSTRACT FROM AUTHOR]

• The onset and termination electric potential to form the steady cone-jet electrospray increase as conductivity increasing. • The lower and upper limitation of liquid flowrate to form the steady cone-jet electrospray decrease as conductivity increases. • The varicose instability can transform into whipping instability as the electrical conductivity increasing. • The jet breakup instability transition mechanism is interpreted by theoretical analysis. • The whipping to similar micro-dripping instability can be observed for EG with higher conductivity. In present work, the effect of the electrical conductivity on the steady cone-jet electrospray are experimentally investigated, where the operating diagram and the jet breakup instability are extensively examined. A hemispherical tube is employed as spraying nozzle severed as high electric potential electrode in a needle-plated electrode configuration compared to the common and sheathed tubes. The cone-jet electrospray is visualized by a high-resolution camera and extensively analyzed offline. The aqueous solution in ethanol, Diethyleneglycol (DEG) and Ethylene glycol (EG) are atomized with varied electrical conductivity under different high electric potentials and flowrates. Experimental results indicate that the cone-jet electrospray can operate in the certain ranges of operating parameter for all types of capillaries. The operating diagram for the hemispherical tube is significantly broader than other tubes because of various electric field strength distribution. The onset electric potential to determine a steady cone-jet electrospray gradually increases and the termination value also increases as the electrical conductivity increases. The lower and upper flowrate to form a steady cone-jet electrospray also increase as the electrical conductivity increases. The jet breakup instability can transit from varicose to whipping due to low the reference flow rate as electrical conductivity increases, which is agreement with theoretical analysis. In particular, for EG, the transition from whipping to similar micro-dripping is observed as the electrical conductivity increases, while the transition also occurs as flowrate increases for EG with higher electrical conductivity. The increase in the electrical conductivity and flowrate elongates the cone due to EHD body force, which causes the electric field varying, further resulting in the difference in jet breakup instability. Moreover, the electrical conductivity also plays an important role in jet breakup length. The instability variation of jet with conductivity (DEG), q V =1000 nL/s, ϕ =8.00 kV (Hemispherical nozzle with D o =0.70mm); The variation with liquid flow rate of EG with higher conductivity (K =8.5 × 10−4 s/m, ϕ =10.20 kV, (Hemispherical nozzle with D o =0.70mm) [Display omitted] [ABSTRACT FROM AUTHOR]