Search

An optimal thruster configuration for attitude control subsystem of a spacecraft is presented in this paper. The optimal configuration is designed according to minimum number of required thrusters for satisfying desired reliability with specific redundancy level. The genetic algorithm is employed for optimization process and feasibility of the results is evaluated using algebraic and geometry methods. The main feature of the proposed configuration among feasible configuration with minimum number of required thrusters, which has held to optimal configuration, is that this configuration has maximum reliability and minimum fuel consumption. In addition to feasibility, attitude control performance of some configurations is also examined through the simulation. The results of simulation confirm that the proposed configuration has desirable performance. It is noteworthy to mention that the configuration with maximum number of required thrusters, which is a conventional configuration such that each thruster belongs to only one control channel, has less fuel consumption than optimal configuration. However, the total mass of optimal configuration is less than that of conventional configuration due to a smaller number of thrusters.

Because they are inexpensive platforms for satellites, CubeSats have become a low-cost way for universities and even developing countries to have access to space technology. This paper presents the ITASAT design, particularly the Attitude Determination and Control Subsystem, the Onboard Software, and the Assembly,Integration and Testing program. The ITASAT is a 6U CubeSat nano-satellite in development at the Instituto Tecnológico de Aeronáutica, in São José dos Campos, Brazil. The platform and its subsystems will be provided by industry while the payloads are being designed and developed by the principal investigators. The ITASAT Attitude Determination and Control Subsystem will rely on a 3-axis magnetometer, 6 analog cosine sun sensors, 3-axis MEMS gyroscopes, 3 magnetic torque coils, and 3 reaction wheels. The Attitude Determination and Control Subsystem operating modes, control laws, and embedded software are under the responsibility of the Instituto Tecnológico de Aeronáutica. A Kalman filter shall be employed to estimate the quaternion attitude and gyroscope biases from sensor measurements. The Attitude Determination and Control Subsystem operating modes are the nominal mode, with geocentric pointing attitude control and the stabilization mode, in which only the satellite angular velocity is controlled. The nominal mode will be split into 2 sub-modes: reaction wheel control plus magnetic wheel desaturation and 3-axis magnetic attitude control. Simulation results have shown that the attitude can be controlled with 1-degree accuracy in nominal mode with the reaction wheels, but these errors grow as much as 20 degrees or higher with the 3-axis magnetic control.

This article has discussed the development of a three-axis attitude digital controller for an artificial satellite using a digital signal processor. The main motivation of this study is the attitude control system of the satellite Multi-Mission Platform, developed by the Brazilian National Institute for Space Research for application in different sort of missions. The controller design was based on the theory of the Linear Quadratic Gaussian Regulator, synthesized from the linearized model of the motion of the satellite, i.e., the kinematics and dynamics of attitude. The attitude actuators considered in this study are pairs of cold gas jets powered by a pulse width/pulse frequency modulator. In the first stage of the project development, a system controller for continuous time was studied with the aim of testing the adequacy of the adopted control. The next steps had included an analysis of discretization techniques, the setting time of sampling rate, and the testing of the digital version of the Linear Quadratic Gaussian Regulator controller in the MATLAB/SIMULINK. To fulfill the study, the controller was implemented in a digital signal processor, specifically the Blackfin BF537 from Analog Devices, along with the pulse width/pulse frequency modulator. The validation tests used a scheme of co-simulation, where the model of the satellite was simulated in MATLAB/SIMULINK, while the controller and modulator were processed in the digital signal processor with a tool called Processor-In-the-Loop, which acted as a data communication link between both environments.function and required time to achieve a given mission accuracy are determined, and results are provided as illustration.

This article has discussed the development of a three-axis attitude digital controller for an artificial satellite using a digital signal processor. The main motivation of this study is the attitude control system of the satellite Multi-Mission Platform, developed by the Brazilian National Institute for Space Research for application in different sort of missions. The controller design was based on the theory of the Linear Quadratic Gaussian Regulator, synthesized from the linearized model of the motion of the satellite, i.e., the kinematics and dynamics of attitude. The attitude actuators considered in this study are pairs of cold gas jets powered by a pulse width/pulse frequency modulator. In the first stage of the project development, a system controller for continuous time was studied with the aim of testing the adequacy of the adopted control. The next steps had included an analysis of discretization techniques, the setting time of sampling rate, and the testing of the digital version of the Linear Quadratic Gaussian Regulator controller in the MATLAB/SIMULINK. To fulfill the study, the controller was implemented in a digital signal processor, specifically the Blackfin BF537 from Analog Devices, along with the pulse width/pulse frequency modulator. The validation tests used a scheme of co-simulation, where the model of the satellite was simulated in MATLAB/SIMULINK, while the controller and modulator were processed in the digital signal processor with a tool called Processor-In-the-Loop, which acted as a data communication link between both environments.function and required time to achieve a given mission accuracy are determined, and results are provided as illustration.