Search

Titanium-zirconium-molybdenum (TZM) alloy was fabricated by using powder metallurgy and rolling techniques. Electrochemical corrosion behavior of the alloy was studied quantitatively using potentiodynamic polarization and scanning electron microscope. Effect of different chloride ions concentrations on corrosion resistance and electrochemical corrosion mechanism on TZM alloy was investigated. Results show that pitting corrosion and intergranular corrosion of TZM alloy mainly occurs in sodium chloride solution. Corrosion generates firstly in the form of pitting corrosion around second phase particles and increases with corrosive media Cl − concentration increasing, and then the intergranular corrosion occurs along grain boundaries and defects. Cl − corrosion can effectively destroy the passive film formed on the sample surface. As the Cl − concentration of corrosive media increases, the corrosion rate of TZM alloy increases until 1.0 mol/L and then decreases. TZM alloy exhibits good corrosion resistance when the concentration of Cl − in corrosive media is 0.5 mol/L or 1.5 mol/L. [ABSTRACT FROM AUTHOR]

Molybdenum powders were high-energy ball milled for 3, 6, 9 and 12 h respectively, using two ball milling methods: (1) dry milled in vacuum and (2) wet milled in mixed solution of ethanol-polyethylene glycol. The effect of high-energy ball milling on relative density of titanium-zirconium-molybdenum (TZM) alloy was investigated. Particle size distribution and calculated proportion in each size range were designed according to the Dinger-Funk model, reaching the dense packing state. The effects of three different kinds of carbon source (graphite, stearic acid (C 18 H 36 O 2 ) and carbon nanotubes (CNTs)) on oxygen content and relative density were analyzed. The effects of carbon source on oxygen content were studied. After high-energy milling, fine molybdenum alloy powder particles and large amounts of dislocations and vacancies are helpful to improve TZM alloy density during solid sintering process. Doping carbon nanotubes (CNTs) into the TZM alloy as carbon source can improve its density and decrease oxygen content, which is more effective than graphite or stearic acid as carbon sources. Higher TZM alloy relative density results in lower oxygen content. [ABSTRACT FROM AUTHOR]

Titanium-Zirconium-Molybdenum alloy and Lanthanum-doped Titanium-Zirconium-Molybdenum alloy were fabricated by powder metallurgy method. The effect of lanthanum in arc erosion of titanium-zirconium-molybdenum alloy was investigated by using SEM, arc erosion test system and analytical balance. Results show that lanthanum-doped Titanium-Zirconium-Molybdenum alloy has a higher strength, density and lower electrical resistivity compared to that of Titanium-Zirconium-Molybdenum alloy. The average of arc energy and the arc time decrease 17.9% and 20.9% respectively because doping lanthanum decreases the arc current by forming reverse current between the contacts. The mass loss decreases 32.5% and erosion area reduces 32.6%. The lanthanum in the cathode has a good ability of electron emission. [ABSTRACT FROM AUTHOR]

La-doping titanium-zirconium-molybdenum alloys have good arc erosion resistance performances, but there is no research about the changes during the arc erosion. Arc erosion characteristics of La-doping titanium-zirconium-molybdenum alloys after 5000 operations under direct current 20 V, 15 A and resistive load conditions were investigated using a JF04C test system. The results indicated that the probability distribution and change trend of arc energy and arc time during 5000 operations were similar and the relationship between arc time and arc energy followed exponential function. The change of arc energy with test number was consistent to electrical resistance. Oxide particles, crater and cracks defects were discovered on the surface of La-doping titanium-zirconium-molybdenum alloy. The electrical resistance change is mainly concerned with the surface. [ABSTRACT FROM AUTHOR]