Search

TiAl-based alloy is an excellent high-temperature structural material, but poor hot workability has been the bottleneck hindering its development. In this study, we take into account the hot workability and mechanical properties of Ti-48Al alloy through microstructure adjustment. Powder metallurgy Ti-48Al alloy prepared by vacuum sintering is used as the raw material, which has a near-γ microstructure composed of equiaxed grains. Although the composition is simple, the alloy achieves high mechanical properties after forging with 75 % deformation. Controlling the forging temperature to 1300 °C can make the microstructure transform into a duplex structure composed of γ/α2 lamellar colonies and γ equiaxed grains. As-forged alloy has an ultimate tensile strength of 650 ± 17 MPa and a yield strength of 644 ± 16 MPa at room temperature. It still maintains high strength at high temperature, with ultimate tensile strength of 684 ± 19 MPa at 500 °C, 700 ± 19 MPa at 700 °C, and 320 ± 10 MPa at 900 °C. In addition, the alloy has good ductility with elongation of 58.2% due to dynamic recrystallization at 900 °C. • Mechanical property is significantly improved by forging with simple composition. • The alloy has ultrafine equiaxed grain of 2.45 µm and lamellar spacing of 20–50 nm. • Duplex microstructure without remnant lamellae forms in PM Ti-48Al alloy. • Ti-48Al alloy exhibits great plasticity of 58.2 % at 900 °C. [ABSTRACT FROM AUTHOR]

Poor sinterability of powder metallurgy TiAl-based alloy is an important factor that restricts its industrial production. In this paper, we improve the sinterability of Ti-48Al alloy by adding Co element. In such case, the relative density of Ti–48Al based alloy sintered at 1250 ℃ increases from 82.6% to 96% with an increase of Co content from 0 to 1.5 at%. The densification improvement is caused by liquid TiAl 2 Co phase, which is formed at 1230 ℃. Then, uniform and fine near-γ microstructure is obtained, and the grain size increases with the increasing of Co content. More than 70% of grains in the Ti-48Al-0.5Co alloy are smaller than 2 µm. Overall, Ti-48Al-0.5Co alloy has better comprehensive performance, with compressive strength of 2533 MPa, yield strength of 683 MPa and fracture strain of 29.5%. [Display omitted] • High-density Ti-48Al alloy with Co addition is prepared using irregular powder. • Liquid TiAl 2 Co phase is formed to promote densification sintering. • Sintering temperature of Co-added TiAl alloy is reduced by 50 ℃. • More than 70% of grains in the Ti-48Al-0.5Co alloy are smaller than 2 µm. • Ti-48Al-0.5Co has superior compressive and yield strengths of 2533 MPa and 683 MPa. [ABSTRACT FROM AUTHOR]

In this paper, the microstructural evolution, precipitation behavior and mechanical properties of 2195 Al-Li alloys prepared by powder metallurgy (PM) combined with hot extrusion were investigated systematically. The results show that the deformation of PM 2195 Al-Li alloys during hot extrusion is dominated by the coupling of dynamic recovery with continuous dynamic recrystallization. The homogeneously distributed needle-like T 1 phase is precipitated in the matrix after T6 treatment. The T6-treated sample exhibits a perfect combination of strength and ductility, that is, ultimate tensile strength of 662 MPa, yield strength of 617 MPa and uniform elongation of 6.6 %. The strengthening of heat-treated alloys originates from densification, work hardening, grain refinement and precipitation strengthening. It is noted that the precipitation strengthening of T 1 phase is the dominant mechanism. Therefore, this work should suggest a strategy for developing novel Al-Li alloys with excellent mechanical properties. • The 2195 Al-Li alloys were successfully prepared by powder metallurgy and hot extrusion. • The tensile strength, yield strength and elongation of the 2195 Al-Li alloy were 662 MPa, 617 MPa and 6.6 %, respectively. • Mechanical properties of the alloy were enhanced by densification, work hardening, grain refinement and precipitation. • The precipitation strengthening of T 1 phase is the dominant mechanism. [ABSTRACT FROM AUTHOR]

Powder metallurgy Cu-30Fe alloy was prepared by mechanical alloying, pressureless sintering, and rolling processes. The alloy microstructure and physical properties affected by rolling were studied. The Fe particles were small and uniformly distributed in the Cu matrix. The average Fe particle size in the sintered state was 1 µm, and particles had subspherical or irregular shapes. The Fe particles became elongated, tadpole-shaped, and spindle-shaped as a result of rolling. At the same time, the Cu grains were elongated and refined, while the Cu grains near the Fe particles were finer as a result of the coordinated deformation of the soft Cu and hard Fe phases. After annealing at 400 °C, the cold-rolled Cu-30Fe alloy had 620 MPa tensile strength, 10% elongation, and 50% IACS electrical conductivity, achieving a good combination of mechanical and functional properties. The coordinated deformation behavior and grain refinement mechanisms of both Cu and Fe phases due to rolling were described, along with the microstructure and physical properties evolution. • Cu-30Fe alloys with Fe particles were fabricated by powder metallurgy and rolling. • Grain refinement mechanisms of Cu and Fe phases due to rolling were described. • Microstructure and physical properties of Cu-30Fe alloys were studied. • Cu-30Fe has 620 MPa tensile strength, 10% elongation, 50%IACS electrical conductivity. [ABSTRACT FROM AUTHOR]