Search

Unlabelled: Clinicians tend to make reductions in glass ionomer power/liquid (P/L) ratios since some materials are difficult to mix and flow into small cavities, grooves or pits. In general, changing the P/L ratio decreases the physical and mechanical properties of conventional glass ionomer cements (GICs) and resin modified glass ionomer cements (RMGICs), but alterations seem to depend on their composition., Objective: To determine the influence of P/L ratio on the radiodensity and diametral tensile strength (DTS) of glass ionomer cements., Material and Methods: There were 2 factors under study: P/L ratio (manufacturer's recommended P/L ratio and a 50% reduced P/L ratio), and materials (Vitro Molar, Vitro Fil, Vitro Cem conventional GICs and Vitro Fil LC, Ortho Glass LC RMGICs. Five 1-mm-thick samples of each material-P/L ratio were produced for radiodensity evaluation. Samples were x-ray exposed onto Digora phosphor plate and radiodensity was obtained using the software Digora for Windows 2.5 Rev 0. For DTS, five (4.0 x 8.0 mm) cylinder samples of each material were tested (0.5 mm/min). Data were subjected to one- and two-way ANOVA (5x2) followed by Tukey's HSD test, or Kruskal-Wallis and Dunn's method. For paired comparisons, t-test or Mann-Whitney test were used (α=0.05)., Results: There was a significant interaction (P=0.001) for the studied factors (materials vs. P/L ratio). Reduced P/L ratio resulted in significantly lower DTS for the RMGICs, but radiodensity was affected for all materials (P<0.05)., Conclusions: Reduced P/L ratio affected properties of the tested glass ionomer cements. RMGICs were more susceptible to lower values of DTS, but radiodensity decreased for all materials following P/L ratio reduction.

Unlabelled: In the most recent decades, several developments have been made on impression materials' composition, but there are very few radiodensity studies in the literature. It is expected that an acceptable degree of radiodensity would enable the detection of small fragments left inside gingival sulcus or root canals., Objective: The aim of this study was to determine the radiodensity of different impression materials, and to compare them to human and bovine enamel and dentin., Material and Methods: Twenty-five impression materials, from 5 classes, were studied: addition and condensation silicones, polyether, polysulfides and alginates. Five 1-mm-thick samples of each material and tooth structure were produced. Each sample was evaluated 3 times (N=15), being exposed to x-ray over a phosphor plate of Digora digital system, and radiodensity was obtained by the software Digora for Windows 2.5 Rev 0. An aluminum stepwedge served as a control. Data were subjected to Kruskal-Wallis and Dunn's method (α=0.05)., Results: Different materials and respective classes had a different behavior with respect to radiodensity. Polysulfides showed high values of radiodensity, comparable to human enamel (p>0.05), but not to bovine enamel (p<0.05). Human dentin was similar only to a heavy-body addition silicon material, but bovine dentin was similar to several materials. Generally, heavy-body materials showed higher radiodensity than light-body ones (p<0.05)., Conclusion: Impression materials' radiodensity are influenced by composition, and almost all of them would present a difficult detection against enamel or dentin background in radiographic examinations.

Bruxism is a pathological activity of the stomatognathic system that involves tooth grinding and clenching during parafunctional jaw movements. Clinical signs of bruxism are mostly related to dental wear and muscular and joint discomforts, but a large number of etiological factors can be listed, as local, systemic, psychological and hereditary factors. The association between bruxism, feeding and smoking habits and digestive disorders may lead to serious consequences to dental and related structures, involving dental alterations (wear, fractures and cracks), periodontal signs (gingival recession and tooth mobility) and muscle-joint sensitivity, demanding a multidisciplinary treatment plan. This paper presents a case report in which bruxism associated with acid feeding, smoking habit and episodes of gastric reflow caused severe tooth wear and great muscular discomfort with daily headache episodes. From the diagnosis, a multidisciplinary treatment plan was established. The initial treatment approach consisted of medical follow up with counseling on diet and smoking habits and management of the gastric disorders. This was followed by the installation of an interocclusal acrylic device in centric relation of occlusion (CRO) for reestablishment of the occlusal stability, vertical dimension of occlusion, anterior guides and return to normal muscle activity (90-day use approximately). After remission of initial symptoms, oral rehabilitation was implemented in CRO by means of full resin composite restorations and new interocclusal device for protection of restorations. Satisfactory esthetics, improved function and occlusal stability were obtained after oral rehabilitation. The patient has attended annual follow-ups for the past 2 years. The multidisciplinary treatment seems to be the key for a successful rehabilitation of severe cases of dental wear involving the association of different health disorders.