Search

The biomechanics of walking are far less understood for uneven terrain than flat or even surfaces. This is due in part to a lack of ground reaction force and moment recordings from each leg. These are often obtained with split-belt instrumented treadmills, which are currently incompatible with uneven terrain, making it difficult to perform biomechanics analyses such as inverse dynamics. Here we show how a standard split-belt instrumented treadmill (Bertec, Inc., Columbus, OH) can be modified to accommodate a variety of uneven terrains. The principal design considerations are structural clearance to allow passage of an uneven treadmill belt and fabrication of the terrain. We designed mechanical components with sufficient clearance for terrains up to 0.045 m high, and formed the terrain from uneven strips of polystyrene. Measured ground reaction forces from each leg at typical walking speeds agreed well with an intact benchmark treadmill (minimum interclass cross correlation score = 0.97). The modifications had negligible effect on the treadmill's structural strength. The terrain produced some noise-like vibrations, but at much higher frequencies than fundamental to human locomotion. The uneven terrain treadmill can record many steps of the full complement of ground reaction forces and moments from individual legs., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Understanding the intricacies of human movement coordination and variability during running is crucial to unraveling the dynamics of locomotion, identifying potential injury mechanisms and understanding skill development. Identification of minimum number of cycles for calculation of reliable coordination and its variability could help with better test organization and efficient assessment time. By adopting a cross-sectional study design, this study investigated the minimum required cycles for calculating hip-knee, hip-ankle and knee-ankle coordination and their variability using a continuous relative phase (CRP) method. Twenty-nine healthy adults ran on a treadmill at speeds of 9, 12.5, and 16 km.h -1 while 3D kinematic data of their lower limbs were recorded using 6 optoelectronic cameras. Using Intraclass Correlation Coefficient (ICC) analysis, reliability between CRP and its variability (CRPv) in different gait cycles (3, 5, 10, 20, 30) was assessed for each speed. A minimum of 10 cycles was required for CRP calculation across all speeds, whereas CRPv necessitated a minimum of 30 cycles for moderate to good reliability. While increasing the number of cycles improved ICC values for inter-joint CRP, the same trend was not consistently observed for CRPv, emphasizing the importance of separately assessing CRP and its variability metrics., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Ltd.)

This study evaluates the efficacy of annuloplasty repair as a standalone procedure for treating bileaflet mitral valve prolapse with mitral regurgitation (MR). Various flexible ring bands for MR of different severities were compared to assess their biomechanical impact and treatment outcomes. Computational beating heart models, based on the Living Heart Human Model, were utilized to simulate annuloplasty repairs. Repairs using bands of varying lengths were modeled on moderate and severe MR cases, considering bileaflet mitral valve prolapse. Key parameters, including regurgitant orifice area (ROA), prolapse severity, coaptation length, leaflet position, and deformation, were computed to compare conditions before and after implantation. Annuloplasty repairs effectively reduced the ROA in both moderate and severe MR cases, achieving complete sealing in selective instances. Additionally, annuloplasty repair corrected bileaflet prolapse, with prolapse severity decreasing as the annular size increased. Successful coaptation was indicated by the expansion of each leaflet's contact area distribution and percentage in contact with the opposing leaflet. The risk of systolic anterior motion, that may obstruct the left ventricular outflow tract, was minimized, as the anterior leaflet was directed towards the posterior position. In conclusion, annuloplasty repair alone can effectively treat MR when an appropriate band length is selected. It facilitates a significant reduction in ROA, correction of bileaflet prolapse, and improvement in leaflet coaptation. These findings have important clinical implications, potentially offering a less complex surgical treatment avenue and reducing complications in the management of MR., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

The understanding of foot and ankle biomechanics is improving as new technology provides more detailed information about the motion of foot and ankle bones with biplane fluoroscopy, as well as the ability to analyze the hindfoot under weightbearing conditions with weightbearing computed tomography. Three-dimensional anatomical coordinate systems are necessary to describe the 3D alignment and kinematics of the foot and ankle. The lack of standard coordinate systems across research study sites can significantly alter experimental data analyses used for pre-surgical evaluation and post-operative outcome assessments. Clinical treatment paradigms are changing based on the expanding knowledge of complex pes planovalgus morphologies or progressive collapsing foot deformity, which is present in both neurologic and non-neurologic populations. Four patient cohorts were created from 10 flexible PCFD, 10 rigid PCFD, 10 adult cerebral palsy, and 10 asymptomatic control patients. Six coordinate systems were tested on both the talus and calcaneus for all groups. The aim of this study was to evaluate axes definitions for the subtalar joint across four different patient populations to determine the influence of morphology on the implementation of previously defined coordinate systems. Different morphologic presentations from various pathologies have a substantial impact on coordinate system definitions, given that numerous axes definitions are defined through geometric fits or manual landmark selection. Automated coordinate systems that align with clinically relevant anatomic planes are preferred. Principal component axes are automatic, but do not align with clinically relevant planes and should not be used for such analysis where anatomic planes are critical., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Ltd.)

Cellular monolayers display various degrees of coordinated motion ranging from the small scale of just a few cells to large multi-cellular scales. This collective migration carries important physical cues for creating proper tissue morphology. Previous studies have demonstrated that the energetics of the epithelial monolayer show a linear variation with time in conjunction with an arrest in monolayer motion after confluency. However, little is known about how the energetics of monolayer development are affected by confined geometries. Here, we demonstrate that micropatterned epithelial monolayers display a non-linear change in energetic variables, which coincides with the large-scale coordination of migration. This non-linear scaling behavior was further seen to be associated with the biased alignment of cells and cell-cell adhesion. These findings provide a new understanding of how developing epithelia may be impacted by different conditions in vivo., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Ltd.)

Interstitial fluid load support (FLS) is a dominant mechanism of lubrication in cartilage, producing a low friction coefficient while enhancing the tissue's load bearing capabilities. Due to its viscosity, synovial fluid (SF) may retard loss of FLS by slowing the exudation of interstitial fluid from the cartilage. This study tested this hypothesis by comparing the stress-relaxation (SRL) response of immature bovine articular cartilage immersed either in phosphate buffered saline (PBS) or in healthy mature bovine SF, under unconfined compression (fluid exudation across cut lateral tissue boundary) and indentation testing (fluid exudation across articular surface). To investigate the influence of diffusion of SF molecular constituents into cartilage, the effect of incubation time in SF on SRL was also investigated. The SRL response in unconfined compression was not significantly different in PBS versus SF when compared directly (p = 0.98) and had a slope ofm = 1.00 ± 0.04 (R 2  = 0.989 ± 0.007). Samples tested in PBS exhibited characteristic relaxation times, τ PBS =42.6 ± 5.3 s andτ SF  = 40.8 ± 4.7 s, that were not significantly different (p = 0.40). Incubation time of 24 h in SF resulted in no significant difference in the SRL response (p = 0.39, m=1.03 ± 0.12; R 2 =0.983 ± 0.011, andτ PBS  = 43.4 ± 10.7 s versusτ SF  = 41.5 ± 4.8 s, p = 0.59). Indentation testing showed some statistically significant, but functionally insignificant, difference in SRL responses in PBS versus SF with a slope ofm = 0.958 ± 0.060 (R 2  = 0.957 ± 0.020, p = 0.029, andτ PBS  = 16.9 ± 2.6 s versusτ SF  = 19.4 ± 3.3 s, p = 0.073). Based on these results, we reject the hypothesis that healthy SF can retard the loss of FLS in cartilage due to its viscosity., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Damage-accumulation failure models are broadly used to examine tissue property changes caused by mechanical loading. However, damage accumulation models are purely phenomenological. The underlying justification in using this type of model is often that damage occurs to the extracellular fibers and/or cells which changes the fundamental mechanical behavior of the system. In this work, we seek to align damage accumulation models with microstructural models to predict alterations in the mechanical behavior of biological materials that arise from structural heterogeneity associated with nonuniform remodeling of tissues. Further, we seek to extend this multiscale model toward assessing catastrophic failure events such as cerebral aneurysm rupture. First, we demonstrate that a model made up of linear elastin and actin and nonlinear collagen fibers can replicate bot the pre-failure and failure tissue-scale mechanics of uniaxially-stretched cerebral aneurysms. Next, we investigate how mechanical heterogeneities, like those observed in cerebral aneurysms, influence fiber and tissue failure. Notably, we find that failure occurs and the interface between regions of high and low material stiffness, suggesting that spatial mechanical heterogeneity influences aneurysm failure behavior. This model system is a step toward linking structural changes in growth and remodeling to failure properties., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

As anterior cruciate ligament (ACL) injuries are highly prevalent among active individuals, it is vital to better understand the loading conditions which lead to injury. One method for doing so is through measurement of dynamic, in vivo ACL strain. To measure strain, it is necessary to normalize elongation of the ACL to a 'reference length' which corresponds to the point at which the ligament transitions from being unloaded to carrying tension. The purpose of this study was to compare the length of the ACL in three different positions to evaluate their utility for establishing a reference (or zero-strain) length of the ACL. ACL reference length was determined using three different methods for each of ten healthy participants. Using magnetic resonance and biplanar radiographic imaging techniques, we measured the length of the ACL during supine resting, quiet standing, and anterior/posterior (AP) drawer testing. During the AP drawer testing, the slack-taut transition point was defined as the inflection point of the AP translation vs ACL elongation curve. There was good consistency between the three ACL length measurements (ICC=0.80). Differences in mean ACL length between the three methods were within 1 mm. While determining the precise zero-strain length of the ACL in vivo remains a challenge, the reference positions utilized in this study produce consistent measurements of ACL length. These findings are important because reliable measurements of in vivo ACL strain have the potential to serve as indicators of propensity for injury., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Ltd.)

Mechanical testing of articular cartilage yields highly variable results, posing challenges for tissue characterization. Many factors cause variability, one is sample geometry. Using in-situ phase-contrast enhanced synchrotron micro-tomographs of cartilage samples while tested in unconfined compression (stress relaxation) our group found high variability in the mechanical response. Since all samples originated from a single bovine knee, they were assumed to share mechanical properties. Microscale tomography images showed geometric irregularities in samples that were not accounted for in the often assumed intended cylindrical shape. We aimed to determine the influence of sample shape on mechanical response in unconfined compression and how sample geometry affects identified mechanical properties. Using a parametric FE model incorporating geometric irregularities in a Design of Experiments approach, results were analysed with 2-way ANOVA. Furthermore, a material parameter fitting was done with multiple segmented sample-specific finite element models simultaneously to assess the influence of sample geometry on material parameters. Results revealed that the average inclined sample surface (4°) caused a 15 % decrease in reaction forces compared to the intended cylinder. Fitting multiple sample-specific geometries simultaneously altered material parameters between -70 to +159 % compared to the average model. Strikingly, initial fibril stiffness and permeability increased by 137 % and 159 %, while the root-mean-square error of the fit was reduced by ∼2/3 compared to using parameters from a cylindrical shape model. In conclusion, minor variability in sample geometry affects property characterization and can account for some of the inter-sample variability in the mechanical data for cartilage., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

The synovium plays a crucial role in diarthrodial joint health, and its study has garnered appreciation as synovitis has been linked to osteoarthritis symptoms and progression. Quantitative synovium structure-function data, however, remain sparse. In the present study, we hypothesized that tissue glycosaminoglycan (GAG) content contributes to the low friction properties of the synovium. Bovine and human synovium tribological properties were evaluated using a custom friction testing device in two different cases: (1) proteoglycan depletion to isolate the influence of tissue GAGs in the synovium friction response and (2) interleukin-1 (IL) treatment to observe inflammation-induced structural and functional changes. Following proteoglycan depletion, synovium friction coefficients increased while GAG content decreased. Conversely, synovium explants treated with the proinflammatory cytokine IL exhibited elevated GAG concentrations and decreased friction coefficients. For the first time, a relationship between synovium friction coefficient and GAG concentration is demonstrated. The study of synovium tribology is necessary to fully understand the mechanical environment of the healthy and diseased joint., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: [Clark T. Hung discloses the following: Royalties from the Musculoskeletal Transplant Foundation, Honorarium for Associate Editor of the Journal of Orthopedic Research, and Editor of Orthopedic Research and Reviews]., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Hamstring strain injuries (HSI) are a common occurrence in athletics and complicated by high rates of reinjury. Evidence of remaining injury observed on magnetic resonance imaging (MRI) at the time of return to sport (RTS) may be associated with strength deficits and prognostic for reinjury, however, conventional imaging has failed to establish a relationship. Quantitative measure of muscle microstructure using diffusion tensor imaging (DTI) may hold potential for assessing a possible association between injury-related structural changes and clinical outcomes. The purpose of this study was to determine the association of RTS MRI-based quantitative measures, such as edema volume, muscle volume, and DTI metrics, with clinical outcomes (i.e., strength and reinjury) following HSI. Spearman's correlations and Firth logistic regressions were used to determine relationships in between-limb imaging measures and between-limb eccentric strength and reinjury status, respectively. Twenty injuries were observed, with four reinjuries. At the time of RTS, between-limb differences in eccentric hamstring strength were significantly associated with principal effective diffusivity eigenvalue λ 1 (r = -0.64, p = 0.003) and marginally associated with mean diffusivity (r = -0.46, p = 0.056). Significant relationships between other MRI-based measures of morphology and eccentric strength were not detected, as well as between any MRI-based measure and reinjury status. In conclusion, this preliminary evidence indicates DTI may track differences in hamstring muscle microstructure, not captured by conventional imaging at the whole muscle level, that relate to eccentric strength., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Select authors of this manuscript declare relationships with the following companies: Dr. Bryan Heiderscheit declares a potential conflict of interest directly related to this work (research support to institution from NBA and GE HealthCare). The other authors (CMW, SAH, MRJ, KL, RK) of this manuscript declare no direct relationships with any companies, whose products or services may be related to the subject matter of the article]., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

There is widespread and growing use of inertial measurement technology for human motion analysis in biomechanics and clinical research. Due to advancements in sensor miniaturization, inertial measurement units can be used to obtain a description of human body and joint kinematics both inside and outside the laboratory. While algorithms for data processing continue to improve, a lack of standard reporting guidelines compromises the interpretation and reproducibility of results, which hinders advances in research and development of measurement and intervention tools. To address this need, the International Society of Biomechanics approved our proposal to develop recommendations on the use of inertial measurement units for joint kinematics analysis. A collaborative effort that incorporated feedback from the biomechanics community has produced recommendations in five categories: sensor characteristics and calibration, experimental protocol, definition of a kinematic model and subject-specific calibration, analysis of joint kinematics, and quality assessment. We have avoided an overly prescriptive set of recommendations for algorithms and protocols, and instead offer reporting guidelines to facilitate reproducibility and comparability across studies. In addition to a conceptual framework and reporting guidelines, we provide a checklist to guide the design and review of research using inertial measurement units for joint kinematics., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Reactive lower limb muscle function during walking plays a key role in balance recovery following tripping, and ultimately fall prevention. The objective of this study was to evaluate muscle and joint function in the recovery limb during balance recovery after trip-based perturbations during walking. Twenty-four healthy participants underwent gait analysis while walking at slow, moderate and fast speeds over level, uphill and downhill inclines. Trip perturbations were performed randomly during stance, and lower limb kinematics, kinetics, and muscle contribution to the acceleration of the whole-body centre of mass (COM) were computed pre- and post-perturbation in the recovery limb. Ground slope and walking speed had a significant effect on lower limb joint angles, net joint moments and muscle contributions to support and propulsion during trip recovery (p < 0.05). Specifically, increasing walking speed during trip recovery significantly reduced hip extension in the recovery limb and increased knee flexion, particularly when walking uphill and at higher walking speeds (p < 0.05). Gluteus maximus played a critical role in providing support and forward propulsion of the body during trip recovery across all gait speeds and ground inclinations. This study provides a mechanistic link between muscle action, joint motion and COM acceleration during trip recovery, and underscores the potential of increased walking speed and ground inclination to increase fall risk, particularly in individuals prone to falling. The findings of this study may provide guidelines for targeted exercise therapy such as muscle strengthening for fall prevention., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Author(s). Published by Elsevier Ltd.. All rights reserved.)

Most children with hemiplegic cerebral palsy (HCP), one of the most prevalent subtypes of cerebral palsy, struggle with grasping and manipulating objects. This impairment may arise from a diminished capacity to properly direct forces created with the finger pad due to aberrant force application. Children with HCP were asked to create maximal force with the index finger pad in the palmar (normal) direction with both the paretic and non-paretic hands. The resulting forces and finger postures were then applied to a computational musculoskeletal model of the hand to estimate the corresponding muscle activation patterns. Subjects tended to create greater shear force relative to normal force with the paretic hand (p < 0.05). The resultant force was directed 33.6°±10.8° away from the instructed palmar direction in the paretic hand, but only 8.0°±7.3° in the non-paretic hand. Additionally, participants created greater palmar force with the non-paretic hand than with the paretic hand (p < 0.05). These differences in force production are likely due to differences in muscle activation pattern, as our computational models showed differences in which muscles are active and their relative activations when recreating the measured force vectors for the two hands (p < 0.01). The models predicted reduced activation in the extrinsic and greater reductions in activation in the intrinsic finger muscles, potentially due to reduced voluntary activation or muscle atrophy. As the large shear forces could lead to objects slipping from grasp, muscle activation patterns may provide an important target for therapeutic treatment in children with HCP., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

The adaptive control of walking is often studied on a split-belt treadmill, where people gradually reduce their step length asymmetries (SLAs) by modulating foot placement and timing. Although it is proposed that this adaptation may be driven in part by a desire to reduce instability, it is unknown if changes in asymmetry impact people's ability to maintain balance in response to destabilizing perturbations. Here, we used intermittent perturbations to determine if changes in SLA affect reactive balance control as measured by whole-body angular momentum (WBAM) in the sagittal and frontal planes. Sixteen neurotypical older adults (70.0 ± 5.3 years old; 6 males) walked on a treadmill at a 2:1 belt speed ratio with real-time visual feedback of their achieved and target step lengths. We used mixed-effects models to determine if there were associations between SLA or foot placement and WBAM during the applied perturbations. Walking with more positive SLAs was associated with small reductions in forward WBAM (p < 0.001 for fast and slow belts) but increased lateral WBAM (p = 0.045 for fast belt; p = 0.003 for slow belt) during perturbations. When participants walked with more positive SLAs, they shortened their foot placement on the slow belt, and this shortening was associated with moderate reductions in forward WBAM (p < 0.001) and small increases in lateral WBAM (p = 0.008) during slow-belt perturbations. Our findings suggest that spatiotemporal changes that occur during split-belt treadmill walking may improve sagittal-plane stability by reducing people's susceptibility to losses of balance, but this may come at the expense of frontal-plane stability., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

The complexity of wrist anatomy and mechanics makes it challenging to develop standardized measurements and establish a normative reference database of wrist biomechanics despite being studied extensively. Moreover, heterogeneity factors in both demographic characteristics (e.g. gender) and physiological properties (e.g. ligament laxity) could lead to differences in biomechanical behaviour even within healthy groups. We investigated the kinematic behaviour of the carpal bones by creating a virtual web-like network between the bones using electromagnetic (EM) sensors. Our objective was to quantify the changes in the carpal bones' biomechanical relative motions and orientations during active wrist motion in the form of orb-web architecture. Models from five cadaveric specimens at different wrist positions: (1) Neutral to 30° Extension, (2) Neutral to 50° Flexion, (3) Neutral to 10° Radial Deviation, (4) Neutral to 20° Ulnar Deviation, and (5) Dart-Throw Motion - Extension (30° Extension/10° RD) to Dart-Throw Motion Flexion (50° Flexion/20° UD), in both neutral and pronated forearm have been analyzed. Quantification analyses were done by measuring the changes in the network thread length, as well as determining the correlation between the threads at different wrist positions. We observed similarities in the kinematic web-network patterns across all specimens, and the interactions between the network threads were aligned to the carpal bones' kinematic behaviour. Furthermore, analyzing the relative changes in the wrist web network has the potential to address the heterogeneity challenges and further facilitate the development of a 3D wrist biomechanics quantitative tool., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Cell volume and shape changes play a pivotal role in cellular mechanotransduction, governing cellular responses to external loading. Understanding the dynamics of cell behavior under loading conditions is essential to elucidate cell adaptation mechanisms in physiological and pathological contexts. In this study, we investigated the effects of dynamic cyclic compression loading on cell volume and shape changes, comparing them with static conditions. Using a custom-designed platform which allowed for simultaneous loading and imaging of cartilage tissue, tissues were subjected to 100 cycles of mechanical loading while measuring cell volume and shape alterations during the unloading phase at specific time points. The findings revealed a transient decrease in cell volume (13%) during the early cycles, followed by a gradual recovery to baseline levels after approximately 20 cycles, despite the cartilage tissue not being fully recovered at the unloading phase. This observed pattern indicates a temporal cell volume response that may be associated with cellular adaptation to the mechanical stimulus through mechanisms related to active cell volume regulation. Additionally, this study demonstrated that cell volume and shape responses during dynamic loading were significantly distinct from those observed under static conditions. Such findings suggest that cells in their natural tissue environment perceive and respond differently to dynamic compared to static mechanical cues, highlighting the significance of considering dynamic loading environments in studies related to cellular mechanics. Overall, this research contributes to the broader understanding of cellular behavior under mechanical stimuli, providing valuable insights into their ability to adapt to dynamic mechanical loading., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

In the Ross procedure, a patient's pulmonary valve is transplanted in the aortic position. Despite advantages of this surgery, reoperation is still needed in many cases due to excessive dilatation of the pulmonary autograft. To further understand the failure mechanisms, we propose a multiscale model predicting adaptive processes in the autograft at the cell and tissue scale. The cell-scale model consists of a network model, that includes important signaling pathways and relations between relevant transcription factors and their target genes. The resulting gene activity leads to changes in the mechanical properties of the tissue, modeled as a constrained mixture of collagen, elastin and smooth muscle. The multiscale model is calibrated with findings from experiments in which seven sheep underwent the Ross procedure. The model is then validated against a different set of sheep experiments, for which a qualitative agreement between model and experiment is found. Model outcomes at the cell scale, including the activity of genes and transcription factors, also match experimentally obtained transcriptomics data., Competing Interests: Declaration of competing interest The authors have no competing interests to declare that are relevant to the content of this article., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Biological tissues decay over time after harvesting, which alters their biomechanical properties. This poses logistical challenges for studies investigating passive arterial biomechanics as tissues need to be characterized shortly after excision. Freezing and cryopreservation methods can help alleviate the need for biomechanical testing of fresh tissue in human ex vivo studies. However, these methods tend to eliminate or reduce arterial cell functionality and affect passive biomechanics. Furthermore, their impact on dynamic arterial biomechanics remains unknown despite arterial viscoelastic properties being an integral component contributing to arterial stiffness under in vivo loading conditions. The present study aims to investigate the impact of rapid cooling and subsequent storage at -80 °C on the passive viscoelastic properties of arterial tissue and aid in ascertaining whether this is a suitable method to delay tissue analysis for studies investigating passive arterial biomechanics. Control and frozen abdominal rat aorta segments were quasi-statically and dynamically tested using a biaxial testing set-up. The results were modeled using a constituent-based quasi-linear viscoelastic modeling framework, yielding directional stiffness parameters, individual constituent biomechanical contributions, and a quantification of viscoelastic stiffening under dynamic pressurization conditions. Frozen samples displayed significantly decreased wall thickness, viscoelastic dissipation, viscoelastic stiffening, and significantly decreased circumferential deformation with changes in luminal pressure. Furthermore, frozen samples displayed significantly increased circumferential stiffness, pulse wave velocity, and collagen load bearing. Consequently, these changes should be considered when utilizing this tissue preservation method to delay biomechanical characterization of rat aortic tissue., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Accurate anatomical coordinate systems for the foot and ankle are critical for interpreting their complex biomechanics. The tibial superior-inferior axis is crucial for analyzing joint kinematics, influencing bone motion analysis during gait using CT imaging and biplane fluoroscopy. However, the lack of consensus on how to define the tibial axis has led to variability in research, hindering generalizability. Even as advanced imaging techniques evolve, including biplane fluoroscopy and weightbearing CT, there exist limitations to imaging the entire foot together with the full length of the tibia. These limitations highlight the need to refine axis definitions. This study investigated various superior-inferior axes using multiple distal tibia lengths to determine the minimal field of view for representing the full tibia long-axis. Twenty human cadaver tibias were imaged and segmented to generate 3D bone models. Axes were calculated based on coordinate definitions that required user manual input, and a gold standard mean superior-inferior axis was calculated based on the population's principal component analysis axis. Four manually calculated superior-inferior tibial axes groups were established based on landmarks and geometric fittings. Statistical analysis revealed that geometrically fitting a cylinder 1.5 times the mediolateral tibial width, starting 5 cm above the tibial plafond, yielded the smallest angular deviation from the gold standard. From these findings, we recommend a minimum field of view that includes 1.5 times the mediolateral tibial width, starting 5 cm above the tibial plafond for tibial long-axis definitions. Implementing these findings will help improve foot and ankle research generalizability and impact clinical decisions., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Degenerative disc disease (DDD), regardless of its phenotype and clinical grade, is widely associated with low back pain (LBP), which remains the single leading cause of disability worldwide. This work provides a quantitative methodology for comparatively investigating artificial IVD degeneration via two popular approaches: enzymatic denaturation and fatigue loading. An in-vitro animal study was used to study the time-dependent responses of forty fresh juvenile porcine thoracic IVDs in conjunction with inverse and forward finite element (FE) simulations. The IVDs were dissected from 6-month-old-juvenile pigs and equally assigned to 5 groups (intact, denatured, low-level, medium-level, high-level fatigue loading). Upon preloading, a sinusoid cyclic load (Peak-to-peak/0.1-to-0.8 MPa) was applied (0.01-10 Hz), and dynamic-mechanical-analyses (DMA) was performed. The DMA outcomes were integrated with a robust meta-model analysis to quantify the poroelastic IVD characteristics, while specimen-specific FE models were developed to study the detailed responses. The results demonstrated that enzymatic denaturation had a more significantly pronounced effect on the resistive strength and shock attenuation capabilities of the intervertebral discs. This can be attributed to the simultaneous disruption of the collagen fibers and water-proteoglycan bonds induced by trypsin digestion. Fatigue loading, on the other hand, primarily influenced the disc's resistance to deformation in a frequency-dependent pattern, where alterations were most noticeable at low loading frequencies. This study confirms the intricate interplay between the biochemical changes induced by enzymatic processes and the mechanical behavior stemming from fatigue loading, suggesting the need for a comprehensive approach to closely mimic the interrelated multifaceted processes of human disc degeneration., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Neck pain and injuries are growing healthcare burdens with women having a higher incidence rate and poorer treatment outcomes than males. A better understanding of sex differences in neck biomechanics, foundational for more targeted, effective prevention or treatment strategies, calls for more advanced subject-specific musculoskeletal modeling. Current neck musculoskeletal models are based on generic anatomy, lack subject specificity beyond anthropometric scaling, and are unable to accurately reproduce neck strengths exhibited in vivo without arbitrary muscle force scaling factors or residual torque actuators. In this work, subject-specific neck musculoskeletal models of 23 individuals (11 male, 12 female) were constructed by integrating multi-modality imaging and biomechanical measurements. Each model simulated maximal voluntary neck static exertions in three postures: neck flexion in a neutral posture, flexion in a 40° extended posture, and extension in a 40° flexed posture. Quantitative model validation showed close agreement between model-predicted muscle activation and EMG measurement. The models unveiled that (1) males have greater moment arms in one flexor muscle group and five extensor muscle groups, (2) females exhibited higher cervical spinal compression per unit exertion force in the flexed posture, and (3) the variability of compression force was much greater in females in all three exertions but most notably in the extension with a flexed "dropped head" position. These insights illuminated a plausible pathway from sex differences in neck biomechanics to sex disparities in the risk and prevalence of neck pain., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

This study investigates the differences in peak plantar pressure between the amputated and intact limbs of transfemoral amputees when walking outdoors. Ten non-amputees (aged 24.4 ± 2.0 years, 176.9 ± 2.5 cm, 72.3 ± 7.9 kg) and six transfemoral amputees (48.5 ± 6.3 years, 173.8 ± 4.2 cm, 82.0 ± 11.9 kg) participated in the study. Over approximately 1.6 km, the participants encountered various obstacles, including stairs, uneven surfaces, hills, and level ground, both indoors and outdoors. Throughout the walking session, the peak plantar pressure in both feet was monitored using wearable insole sensors. For all terrains, the percentage asymmetry was determined. Significant changes in peak plantar pressure asymmetry were found between the intact and amputated limbs, particularly when walking on level ground indoors, uneven terrains, descending stairs, and on steep slopes outdoors (all p < 0.05). These findings highlight the greater peak plantar pressure asymmetry in transfemoral amputees when walking outside. In addition, this study revealed that not all terrains contribute uniformly to this asymmetry., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Ltd.)

One of the most significant developments in prosthetic knee technology has been the introduction of the Microprocessor-Controlled Prosthetic Knee (MPK). However, there is a lack of consensus over how different types of MPKs affect performance in different ambulation modes. In this study, we investigated the biomechanical differences in ramp and stair maneuvers when an individual with transfemoral amputation wears three commercial MPKs: the Össur Power Knee, the Össur Rheo Knee and the Ottobock C-Leg 4. The primary outcome variable for this study was the lower limb biological joint work, inclusive of the intact leg and prosthetic side hip. We hypothesized that (1) the Power Knee would result in lower biological work during ascent activities than the C-Leg and Rheo, both passive MPKs, and (2) the C-Leg and Rheo would result in lower biological work during descent activities than the Power Knee. During ramp ascent, the C-Leg was associated with lower biological joint work (p < 0.05) than the Power Knee. However, this relationship did not hold during stair ascent, where the Power Knee showed advantages for stair ascent with net reductions in biological joint work of 14.1% and 23.3% compared to the Rheo and C-leg, respectively. There were no significant differences in biological joint work between the knees during ramp and stair descent, indicating that choice of MPK may not be as important for descent activities. Our results demonstrate that differences are present between different types of MPKs during ascent activities which could prove useful in the prescription of these devices., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Whole-body angular momentum (WBAM) represents the cancellations of angular momenta that are produced during a reciprocal gait pattern. WBAM is sensitive to small changes and is used to compare dynamic gait patterns under different walking conditions. Study designs and the normalization techniques used to define WBAM vary and make comparisons between studies difficult. To address this problem, WBAM about each anatomical axis of rotation from a healthy control population during normal gait were investigated within four metrics: 1) range of WBAM, 2) integrated WBAM, 3) statistical parametric mapping (SPM), and 4) principal component analysis (PCA). These data were studied as a function of walking speed and normalization. Normalization techniques included: 1) no normalization, 2) normalization by height, body mass and walking speed, and 3) normalization by height, body mass and a scalar number, gravity×height, that is independent of walking velocity. Significant results were obtained as a function of walking speed regardless of normalization technique. However, the interpretation of significance within each metric was dependent on the normalization technique. Method 3 was the most robust technique as the differences were not altered from the expected relationships within the raw data. Method 2 actually inverted the expected relationship in WBAM amplitude as a function of walking speed, which skewed the results and their interpretation. Overall, SPM and PCA statistical methods provided better insights into differences that may be important. However, depending on the normalization technique used, caution is advised when interpreting significant findings when comparing participants with disparate walking speeds., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Congenital arterial stenosis such as supravalvar aortic stenosis (SVAS) are highly prevalent in Williams syndrome (WS) and other arteriopathies pose a substantial health risk. Conventional tools for severity assessment, including clinical findings and pressure gradient estimations, often fall short due to their susceptibility to transient physiological changes and disease stage influences. Moreover, in the pediatric population, the severity of these and other congenital heart defects (CHDs) often restricts the applicability of invasive techniques for obtaining crucial physiological data. Conversely, evaluating CHDs and their progression requires a comprehensive understanding of intracardiac blood flow. Current imaging modalities, such as blood speckle imaging (BSI) and four-dimensional magnetic resonance imaging (4D MRI) face limitations in resolving flow data, especially in cases of elevated flow velocities. To address these challenges, we devised a computational framework employing zero-dimensional (0D) lumped parameter models coupled with patient-specific reconstructed geometries pre- and post-surgical intervention to execute computational fluid dynamic (CFD) simulations. This framework facilitates the analysis and visualization of intricate blood flow patterns, offering insights into geometry and flow dynamics alterations impacting cardiac function. In this study, we aim to assess the efficacy of surgical intervention in correcting an extreme aortic defect in a patient with WS, leading to reductions in wall shear stress (WSS), maximum velocity magnitude, pressure drop, and ultimately a decrease in cardiac workload., Competing Interests: Declaration of competing interest The authors declare no conflicts of interest., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Gait for individuals with movement disorders varies widely and the variability makes it difficult to assess outcomes of surgical and therapeutic interventions. Although specific joints can be assessed by fewer individual measures, gait depends on multiple parameters making an overall assessment metric difficult to determine. A holistic, summary measure can permit a standard comparison of progress throughout treatments and interventions, and permit more straightforward comparison across varied subjects. We propose a single summary metric (the Shriners Gait Index (SGI)) to represent the quality of gait using a deep learning autoencoder model, which helps to capture the nonlinear statistical relationships among a number of disparate gait metrics. We utilized gait data of 412 individuals under the age of 18 collected from the Motion Analysis Center (MAC) at the Shriners Children's - Chicago. The gait data includes a total of 114 features: temporo-spatial parameters (7), lower extremity kinematics (64), and lower extremity kinetics (43) which were min-max normalized. The developed SGI score captured more than 89% variance of all 144 features using subject-wise cross-validation. Such summary metrics holistically quantify an individual's gait which can then be used to assess the impact of therapeutic interventions. The machine learning approach utilized can be leveraged to create such metrics in a variety of contexts depending on the data available. We also utilized the SGI to compare overall changes to gait after surgery with the goal of improving mobility for individuals with gait disabilities such as Cerebral Palsy., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Shou-Jen Wang, Thasina Tabashum, Karen M. Kruger, Joseph J Krzak, Adam Graf, Ross S. Chafetz, Judi Linton, Jon Davids, Anita Bagley, Mark V. Albert reports financial support was provided by Shriners Children’s. Jon Davids reports a relationship with Ortho Pediatrics that includes: consulting or advisory. The funders had no role in the design of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript; or in the decision to publish the results., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

The healthy adult aorta is a remarkably resilient structure, able to resist relentless cardiac-induced and hemodynamic loads under normal conditions. Fundamental to such mechanical homeostasis is the mechano-sensitive cell signaling that controls gene products and thus the structural integrity of the wall. Mouse models have shown that smooth muscle cell-specific disruption of transforming growth factor-beta (TGFβ) signaling during postnatal development compromises this resiliency, rendering the aortic wall susceptible to aneurysm and dissection under normal mechanical loading. By contrast, disruption of such signaling in the adult aorta appears to introduce a vulnerability that remains hidden under normal loading, but manifests under increased loading as experienced during hypertension. We present a multiscale (transcript to tissue) computational model to examine possible reasons for compromised mechanical homeostasis in the adult aorta following reduced TGFβ signaling in smooth muscle cells., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Ltd.)

Acute alcohol ingestion has been found to impact visual functions, including eye movement, but its effects on corneal biomechanical properties remain unclear. This study aimed to investigate the influence of acute alcohol consumption on corneal biomechanical properties using optical coherence elastography (OCE). An air-coupled ultrasound transducer induced elastic waves in mice corneas in vivo, and a high-resolution phase-sensitive optical coherence tomography (OCT) system tracked the mechanical waves to quantify the elastic wave speed. In vivo measurements were performed on three groups of age- and gender-matched mice: control, placebo (administered saline), and alcohol (administered ethanol) groups. Longitudinal measurements were conducted over a one-hour period to assess acute temporal changes in wave speeds, which are associated with inherent biomechanical properties of the cornea. The results showed a significant decrease in wave speed for the alcohol group after 10 min of ingestion in comparison to pre-ingestion values (p = 0.0096), whereas the temporal wave speed changes for the placebo group were statistically insignificant (p = 0.076). In contrast, the control group showed no significant changes in elastic wave speed and corneal thickness. Furthermore, a significant difference was observed between the wave speeds of the placebo and alcohol groups at each measurement time point between 10 and 50 min (p < 0.05), though both groups exhibited a similar trend in corneal thickness change. The findings of this study have important implications for clinical assessments and research in corneal disorders, highlighting the potential of OCE as a valuable tool for evaluating such changes., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: MS and KVL have financial interests in ElastEye LLC., which is not directly related to this work., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Atomic force microscopy (AFM) is a valuable tool for assessing mechanical properties of biological samples, but interpretations of measurements on whole tissues can be difficult due to the tissue's highly heterogeneous nature. To overcome such difficulties and obtain more robust estimates of tissue mechanical properties, we describe an AFM force mapping and data analysis pipeline to characterize the mechanical properties of cryosectioned soft tissues. We assessed this approach on mouse optic nerve head and rat trabecular meshwork, cornea, and sclera. Our data show that the use of repeated measurements, outlier exclusion, and log-normal data transformation increases confidence in AFM mechanical measurements, and we propose that this methodology can be broadly applied to measuring soft tissue properties from cryosections., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Ltd.)

Ligaments and tendons undergo nonuniform deformation during movement. While deformations can be imaged, it remains challenging to use such information to infer regional tissue loading. Shear wave tensiometry is a promising noninvasive technique to gauge axial stress and is premised on a tensioned beam model. However, it is unknown whether tensiometry can predict regional stress in a nonuniformly loaded structure. The objectives of this study were to (1) determine whether regional shear wave speed tracks regional axial stress in nonuniformly loaded fibrous soft tissues, and (2) determine the sensitivity of regional axial stress and shear wave speed to nonuniform load distribution and fiber alignment. We created a representative set of 12,000 dynamic finite element models of a fibrous soft tissue with probabilistic variations in fiber alignment, stiffness, and aspect ratio. In each model, we applied a randomly selected nonuniform load distribution, and then excited a shear wave and tracked its regional propagation. We found that regional shear wave speed was an excellent predictor of the regional axial stress (RMSE = 0.57 MPa) and that the nature of the regional shear wave speed-stress relationship was consistent with a tensioned beam model (R 2  = 0.99). Variations in nonuniform load distribution and fiber alignment did not substantially alter the wave speed-stress relationship, particularly at higher loads. Thus, these findings suggests that shear wave tensiometry could provide a quantitative estimate of regional tissue stress in ligaments and tendons., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Persons with Parkinson's disease experience gait alterations, such as reduced step length. Gait dysfunction is a significant research priority as the current treatments targeting gait impairment are limited. This study aimed to investigate the effects of visual biofeedback on propulsive force during treadmill walking in persons with Parkinson's. Sixteen ambulatory persons with Parkinson's participated in the study. They received real-time biofeedback of anterior ground reaction force during treadmill walking at a constant speed. Peak propulsive force values were measured and normalized to body weight. Spatiotemporal parameters were also assessed, including stride length and double support percent. Persons with Parkinson's significantly increased peak propulsive force during biofeedback compared to baseline (p <.0001, Cohen's dz = 1.69). Variability in peak anterior ground reaction force decreased across repeated trials (p <.0001, dz = 1.51). While spatiotemporal parameters did not show significant changes individually, stride length and double support percent improved marginally during biofeedback trials. Persons with Parkinson's can increase propulsive force with visual biofeedback, suggesting the presence of a propulsive reserve. Though stride length did not significantly change, clinically meaningful improvements were observed. Targeting push-off force through visual biofeedback may offer a potential rehabilitation technique to enhance gait performance in Persons with Parkinson's. Future studies could explore the long-term efficacy of this intervention and investigate additional strategies to improve gait in Parkinson's disease., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Using a smartphone often involves a sustained head-forward tilt posture, which may deteriorate the mechanism of muscle reaction efficiency or reduce the stiffness of connective tissues of the cervical spine. These changes in muscular and connective tissues can impair cervical spine stability and contribute to developing neck pain symptoms. In this experiment, change in the cervical spine stability associated with a sustained smartphone use posture was evaluated by quantifying the effective stiffness and the reflexive responses of the head to sudden perturbations. Seventeen young smartphone users maintained their heads tilted forward approximately 30° for 30 min while watching videos on their smartphones in sitting. Data show that the measures of cervical spine stability did not change significantly after the smartphone use task despite developing mild to moderate neck and upper body discomfort symptoms. Study findings imply that keeping the head tilt posture for 30 min for smartphone use did not significantly alter spinal stability, rejecting its association with neck discomfort., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

The objective of this study was to define targeted reaching performance without visual information for transhumeral (TH) prosthesis users, establishing baseline information about extended physiological proprioception (EPP) in this population. Subjects completed a seated proprioceptive targeting task under simultaneous motion capture, using their prosthesis and intact limb. Eight male subjects, median age of 58 years (range 29-77 years), were selected from an ongoing screening study to participate. Five subjects had a left-side TH amputation, and three a right-side TH amputation. Median time since amputation was 9 years (range 3-54 years). Four subjects used a body-powered prosthetic hook, three a myoelectric hand, and one a myoelectric hook. The outcome measures were precision and accuracy, motion of the targeting hand, and joint angular displacement. Subjects demonstrated better precision when targeting with their intact limb compared to targeting with their prosthesis, 1.9 cm2 (0.8-3.0) v. 7.1 cm2 (1.3-12.8), respectively, p = 0.008. Subjects achieved a more direct reach path ratio when targeting with the intact limb compared to with the prosthesis, 1.2 (1.1-1.3) v. 1.3 (1.3-1.4), respectively, p = 0.039 The acceleration, deceleration, and corrective phase durations were consistent between conditions. Trunk angular displacement increased in flexion, lateral flexion, and axial rotation while shoulder flexion decreased when subjects targeted with their prosthesis compared to the intact limb. The differences in targeting precision, reach patio ratio, and joint angular displacements while completing the targeting task indicate diminished EPP. These findings establish baseline information about EPP in TH prosthesis users for comparison as novel prosthesis suspension systems become more available to be tested., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Force-sensing insoles are wearable technology that offer an innovative way to measure loading outside of laboratory settings. Few studies, however, have utilized insoles to measure daily loading in real-world settings. This is an ancillary study of a randomized controlled trial examining the effect of weight loss alone, weight loss plus weighted vest, or weight loss plus resistance training on bone health in older adults. The purpose of this ancillary study was to determine the feasibility of using force-sensing insoles to collect daily limb loading metrics, including peak force, impulse, and loading rate. Forty-four participants completed a baseline visit of three, 2-minute walking trials while wearing force-sensing insoles. During month two of the intervention, 37 participants wore insoles for 4 days for 8 waking hours each day. At 6-month follow-up, participants completed three, two-minute walking trials and a satisfaction questionnaire. Criteria for success in feasibility was defined as: a) > 60 % recruitment rate; b) > 80 % adherence rate; c) > 75 % of usable data, and d) > 75 % participant satisfaction. A 77.3 % recruitment rate was achieved, with 44 participants enrolled. Participants wore their insoles an average of 7.4 hours per day, and insoles recorded an average of 5.5 hours per day. Peak force, impulse, and loading rate collected at baseline and follow-up were 100 % usable. During the real-world settings, 87.8 % of data was deemed usable with an average of 1200 min/participant. Lastly, average satisfaction was 80.5 %. These results suggest that force-sensing insoles appears to be feasible to capture real-world limb loading in older adults., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Ltd.)

Segment coordinate systems (CSs) of marker-based multi-segment foot models are used to measure foot kinematics, however their relationship to the underlying bony anatomy is barely studied. The aim of this study was to compare marker-based CSs (MCSs) with bone morphology-based CSs (BCSs) for the hindfoot and forefoot. Markers were placed on the right foot of fifteen healthy adults according to the Oxford, Rizzoli and Amsterdam Foot Model (OFM, RFM and AFM, respectively). A CT scan was made while the foot was loaded in a simulated weight-bearing device. BCSs were based on axes of inertia. The orientation difference between BCSs and MCSs was quantified in helical and 3D Euler angles. To determine whether the marker models were able to capture inter-subject variability in bone poses, linear regressions were performed. Compared to the hindfoot BCS, all MCSs were more toward plantar flexion and internal rotation, and RFM was also oriented toward more inversion. Compared to the forefoot BCS, OFM and RFM were oriented more toward dorsal and plantar flexion, respectively, and internal rotation, while AFM was not statistically different in the sagittal and transverse plane. In the frontal plane, OFM was more toward eversion and RFM and AFM more toward inversion compared to BCS. Inter-subject bone pose variability was captured with RFM and AFM in most planes of the hindfoot and forefoot, while this variability was not captured by OFM. When interpreting multi-segment foot model data it is important to realize that MCSs and BCSs do not always align., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Author(s). Published by Elsevier Ltd.. All rights reserved.)

Using high frame-rate ultrasound and ¡1μm sensitive motion tracking we previously showed that shear waves at the surface of ex vivo and in situ brains develop into shear shock waves deep inside the brain, with destructive local accelerations. However post-mortem tissue cannot develop injuries and has different viscoelastodynamic behavior from in vivo tissue. Here we present the ultrasonic measurement of the high-rate shear shock biomechanics in the in vivo porcine brain, and histological assessment of the resulting axonal pathology. A new biomechanical model of brain injury was developed consisting of a perforated mylar surface attached to the brain and vibrated using an electromechanical shaker. Using a custom sequence with 8 interleaved wide beam emissions, brain imaging and motion tracking were performed at 2900 images/s. Shear shock waves were observed for the first time in vivo wherein the shock acceleration was measured to be 2.6 times larger than the surface acceleration ( 95g vs. 36g). Histopathology showed axonal damage in the impacted side of the brain from the brain surface, accompanied by a local shock-front acceleration of >70g. This shows that axonal injury occurs deep in the brain even though the shear excitation was at the brain surface, and the acceleration measurements support the hypothesis that shear shock waves are responsible for deep traumatic brain injuries., Competing Interests: Declaration of competing interest We have no conflicts of interest to disclose., (Copyright © 2024. Published by Elsevier Ltd.)

Cement-augmentation is a technique commonly used during posterior lumbar instrumented fusion (PLIF) to reinforce compromised osteoporotic vertebral bone, minimize the risk of loosening screws, enhance stability, and improve overall surgical outcomes. In this study, we introduce a novel segmented vertebral body regional modeling approach to investigate the effects of osteoporosis and cement-augmented lumbar fusion on disc biomechanics at spinal levels adjacent to the fused vertebrae. Using our previously validated personalized-poroelastic-osteoligamentous FE model of the spine, fusion was simulated at L4-L5, and the biomechanics of adjacent levels were studied for 30 patients (non-osteoporotic patients (N = 15), osteoporotic patients (N = 15)). PLIF models, with and without cement-augmentation, were developed and compared after an 8 h-rest period (200 N), following a 16 h-cyclic compressive loading of 500-1000 N (40 and 20 min, respectively). Movement in different directions (flexion/ extension/ lateral bending/ axial rotation) was simulated using 10Nm moment before and after cyclic loading. The material mapping algorithm was validated by comparing the results of voxel-based and parametric models. The FE cement-augmented models, subject to daily activity loading, demonstrated significant differences in disc height loss and fluid loss as compared to non-cemented models. The calculated axial stress and fiber strain values were also significantly higher for these models. This work demonstrates that although osteoporosis does not significantly alter the time-dependent characteristics of adjacent IVDs post-surgery, cement-augmentation increases the risk of adjacent segment disease (ASD) incidence. A holistic understanding of the trade-offs and long-term complex interplay between structural reinforcement modalities, including cement augmentation, and altered biomechanics warrants further investigation., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Glenohumeral biomechanics after rotator cuff (RC) tears have not been fully elucidated. This study aimed to investigate the muscle compensatory mechanism in weight-bearing shoulders with RC tears and asses the induced pathomechanics (i.e., glenohumeral translation, joint instability, center of force (CoF), joint reaction force). An experimental, glenohumeral simulator with muscle-mimicking cable system was used to simulate 30° scaption motion. Eight fresh-frozen shoulders were prepared and mounted in the simulator. Specimen-specific scapular anthropometry was used to test six RC tear types, with intact RC serving as the control, and three weight-bearing loads, with the non-weight-bearing condition serving as the control. Glenohumeral translation was calculated using instantaneous helical axis. CoF, muscle forces, and joint reaction forces were measured using force sensors integrated into the simulator. Linear mixed effects models (RC tear type and weight-bearing) with random effects (specimen and sex) were used to assess differences in glenohumeral biomechanics. RC tears did not change the glenohumeral translation (p > 0.05) but shifted the CoF superiorly (p ≤ 0.005). Glenohumeral translation and joint reaction forces increased with increasing weight bearing (p < 0.001). RC and deltoid muscle forces increased with the presence of RC tears (p ≤ 0.046) and increased weight bearing (p ≤ 0.042). The synergistic muscles compensated for the torn RC tendons, and the glenohumeral translation remained comparable to that for the intact RC tendons. However, in RC tears, the more superior CoF was close to where glenoid erosion occurs in RC tear patients with secondary osteoarthritis. These findings underscore the importance of early detection and precise management of RC tears., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Author(s). Published by Elsevier Ltd.. All rights reserved.)

Nucleus pulposus (NP) tissue in the intervertebral disc (IVD) is a viscoelastic material exhibiting both solid- and fluid-like mechanical behaviors. Advances in viscoelastic models incorporating fractional calculus, such as the Fractional Zener (FZ) model, have potential to describe viscoelastic behaviors. The objectives of this study were to determine whether the FZ model can accurately describe the shear viscoelastic properties of NP tissue and determine if the fractional order (α) is related to tissue hydration. 30 caudal IVDs underwent equilibrium dialysis in 5% or 25% polyethylene glycol solutions to alter tissue hydration. Excised NP tissue underwent stress relaxation testing in shear and unconfined compression. Stress relaxation data was fitted to the FZ model to obtain viscoelastic properties. In both loading modes, the initial modulus was greater for the less hydrated 25% equilibrated samples compared to 5% with no change in the equilibrium modulus. Samples with lower water content (25% samples) had shorter relaxation times in shear and longer time constants in compression, highlighting the different interactions between the fluid and solid matrix in loading modes. Samples with lower water content had α values closer to 0, indicating that less hydrated samples behaved more solid-like on the viscoelastic spectrum. Tissue hydration correlated with α values for 25% samples in shear. This study demonstrates that the FZ model may be used to describe IVD tissue behavior under both loading modes; however, the greatest utility of the FZ model is in describing flow-independent shear behaviors, and α may inform tissue hydration in shear., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Author(s). Published by Elsevier Ltd.. All rights reserved.)

Total ankle arthroplasty (TAA) is a common surgical solution for patients with debilitating arthritis of the ankle. Prior to surgery patients experience high levels of pain and fatigue and low mechanical energy recovery. It is not known if TAA restores healthy levels of mechanical energy recovery in this patient population. This study was designed to determine whether mechanical energy recovery was restored following TAA. Ground reaction forces during self-selected speed walking were collected from patients with symptomatic, unilateral ankle arthritis (N = 29) before and one and two years after primary, unilateral TAA. The exchange of potential (PE) and kinetic (KE) energy was examined, and direction of change (%congruity) and energy exchange (%recovery) between the two curves was calculated, with those subjects with low congruity experiencing high energy recovery. Linear regressions were used to examine the impact of walking speed, congruity, and amplitude of the center of mass (COM) displacement on %recovery, while ANOVA and ANCOVA models were used to compare energy recovery and congruity across the three time points. Gender, BMI, and age at surgery had no effect in this study. TAA improved walking speed (p = 0.001), increased energy recovery (p = 0.020), and decreased congruity (p = 0.002), and these levels were maintained over at least two years. Differences in congruity were independent of walking speed. In some patients, especially those who are severely debilitated by ankle arthritis, TAA is effective in restoring mechanical energy recovery to levels similar to an asymptomatic population of a similar age recorded by other studies., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Ltd.)

Upper extremity kinematics are important for understanding functional ability and performance improvements. The Box and Blocks test (BBT) is a standardized functional test used to measure manual dexterity when evaluating children or patients following a stroke. The BBT measures the number of blocks moved in one minute and therefore, kinematic measures and compensatory strategies cannot be assessed. This study examined the correlation between upper extremity kinematics and cycle time per block movement during the BBT in three age groups (7-, 9-, and 11-year-olds). Participants completed one BBT session while test scores and kinematic measures (hand velocity and position and shoulder, elbow, and wrist range of motion and peak joint angles) were captured using standard three-dimensional motion capture techniques. Kinematic measures were determined for block movements during the middle of each BBT trial. A mixed-effects model was used to identify group differences (α = 0.05). BBT score was different (p = 0.005) between the 7- (44.88 ± 6.03) and the 11-year-old age group (56.95 ± 8.37) along with peak shoulder flexion (p = 0.024) and abduction (p = 0.022). Peak elbow flexion was different (p = 0.049) between the 9- and 11-year-old age groups. No differences were seen between the 7- and 9-year-old age groups. Pearson's Correlation Coefficients were determined between cycle time and each significant kinematic measure, where the cycle time is specific to each block movement (BBT score) and is correlated to the BBT score. This resulted in weak correlations for all the comparisons. Therefore, using BBT score alone is not representative of UE kinematics and both should be collected during this task to provide insight into movement mechanics in a pediatric population., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Chronic ankle instability is a condition linked to progressive early ankle joint degeneration. Patients with chronic ankle instability exhibit altered biomechanics during gait and jump landings and these alterations are believed to contribute to aberrant joint loading and subsequent joint degeneration. Musculoskeletal modeling has the capacity to estimate joint loads from individual muscle forces. However, the influence of chronic ankle instability on joint contact forces remains largely unknown. The objective of this study was to compare tri-axial (i.e., compressive, anterior-posterior, and medial-lateral) ankle joint contact forces between those with and without chronic ankle instability during the ground contact phase of a drop vertical jump. Fifteen individuals with and 15 individuals without chronic ankle instability completed drop vertical jump maneuvers in a research laboratory. We used those data to drive three-dimensional musculoskeletal simulations and estimate muscle forces and tri-axial joint contact force variables (i.e., peak and impulse). Compared to those without chronic ankle instability, the ankles of patients with chronic ankle instability underwent lower compressive ankle joint contact forces as well as lower anterior-posterior and medial-lateral shearing forces during the weight acceptance phase of landing (p <.05). These findings suggest that patients with chronic ankle instability exhibit lower ankle joint loading patterns than uninjured individuals during a drop vertical jump, which may be considered in rehabilitation to potentially reduce the risk of early onset of ankle joint degeneration., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Published by Elsevier Ltd.)

Morphological changes of the nucleus pulposus (NP) cells occur concomitantly as part of the intervertebral disc (IVD) degeneration and excessive mechanical loading has been speculated as a significant key factor for contributing to such morphological changes. Therefore, we hypothesize that stress exerted on NP cells can cause a deformity of nucleus in response. The changes of cell morphology is observed in degenerative nucleus pulposus. One of the reasons for degeneration of NP is due to overloading of NP especially in the obese population. So the nucleus deformity caused by stress/force is of our study interest. To delineate the effects and role of mechanical stress, we developed a 3D assay using hydrogel cultures with a circular hole generated with needle indentation to simulate a local stress concentration along the edge of the hole. A stressed zone, encompassing 100 μm of range from the circular edge, is defined based on stress concentration calculation to enable quantitative analysis against the control zone. Our results demonstrated that the circular hole produces stress-induced morphological changes in NP cells. The tangential elongation of NP cells and their nucleus shape changes in the stressed zone are significantly increased compared to the non-stressed control zone. It is proposed that the cell elongation is a direct response to elevated stress within the stressed zone. Subsequently we found the stress induced morphological changes of the NP cells can be significantly reduced by inhibiting ASIC3. This suggests ASIC3 plays an important role of play in mechano-signaling of NP cells., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Jaw-Lin Wang reports financial support was provided by Ministry of Science and Technology, Taiwan. Jaw-Lin Wang reports financial support was provided by National Health Research Institute, Taiwan. Jaw-Lin Wang reports a relationship with Ministry of Science and Technology, Taiwan that includes: funding grants., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

The high water content of articular cartilage allows this biphasic tissue to withstand large compressive loads through fluid pressurization. The system presented here, termed the "MagnaSquish", provides new capabilities for quantifying the effect of rehydration on cartilage behavior during cyclic loading. An imbalanced rate of fluid exudation during load and fluid re-entry during recovery can lead to the accumulation of strain during successive loading cycles - a phenomenon known as ratcheting. Typical experimental systems for cartilage biomechanics use continuous contact between the platen and sample, which may affect tissue rehydration by compressing the top layer of cartilage and slowing fluid re-entry. To address this limitation, we developed a magnetically actuated device that provides full lift-off of the platen in between loading cycles. We investigated strain accumulation in cadaveric human osteochondral plugs during 750 loading cycles, with two dimensional profiles of the cartilage captured at 30 frames per second throughout loading and 10 min of additional free swelling recovery. Axial and lateral strain measurements were extracted from the tissue profiles using a UNet-based deep learning algorithm to circumvent manual tracing. We observed increased axial strain accumulation with shorter inter-cycle recovery, with static loading serving as the extreme case of zero recovery. The loading waveform during the 750 cycles dictated the pace of the recovery during the extended free swelling period, as shorter inter-cycle recovery led to more persistent axial strain accumulation for up to five minutes. This work showcases the importance of fluid re-entry in resisting strain accumulation during cyclical compression., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

The long head biceps tendon (LHBT) is presumed a common source of shoulder joint pain and injury. Despite common LHBT pathologies, diagnosis and preferred treatment remain frequently debated. This Short Communication reports the development of a subject-specific finite element model of the shoulder joint based on one subject's 3D reconstructed anatomy and 3D in vivo kinematics recorded from bone-fixed electromagnetic sensors. The primary purpose of this study was to use the developed finite element model to investigate the LHBT mechanical environment during a typical shoulder motion of arm raising. Furthermore, this study aimed to assess the viability of material models derived from uniaxial tensile tests for accurate simulation of in vivo motion. The findings of our simulations indicate that the LHBT undergoes complex multidimensional deformations. As such, uniaxial material properties reported in the existing body of literature are not sufficient to simulate accurately the in vivo mechanical behavior of the LHBT. Further experimental tests on cadaveric specimens, such as biaxial tension and combinations of tension and torsion, are needed to describe fully the mechanical behavior of the LHBT and investigate its mechanisms of injury., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

Studies of human locomotion have observed asymmetries in lower-limb kinematics, especially at the more distal joints. However, it is unclear whether these asymmetries are related to functional differences between the dominant and non-dominant limb. This study aimed to determine the effect of lower-limb dominance on foot kinematics during human locomotion. Range of motion for the metatarsophalangeal joint (MPJ) and medial longitudinal arch (MLA), as well as time duration of windlass mechanism engagement, were recorded from healthy young adults (N = 12) across a range of treadmill walking and running speeds. On the group level, there were no differences in MPJ or MLA range of motion, or windlass engagement timing, between the dominant and non-dominant limb (p > 0.05). While not explained by limb dominance, between-limb differences in MPJ and MLA ranges of motion were observed for individual participants on the order of ∼2-6°, which could be clinically relevant or impact interpretation of research data., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Altered medial/lateral knee muscle co-contraction (measure by co-contraction indices, CCI) occurs during gait early after anterior cruciate ligament reconstruction (ACLR). Changes in peak medial compartment forces (pMCF) are also observed early after ACLR and are linked to the development of knee osteoarthritis. We do not know if imbalanced co-contraction is associated with these alterations in knee load. The purpose of this study was to evaluate the association between pMCF and the CCIs of medial/lateral knee muscle pairs during walking three months after ACLR. Bilateral knee gait mechanics and electromyography (EMG) data were collected from 44 participants 3 months following surgery. CCIs of six muscle pairs and medial-to-lateral (M:L) CCIs ratios were calculated during the weight acceptance interval. Bilateral pMCFs were calculated using a subject-based neuromusculoskeletal model. Based on interlimb pMCF symmetry, participants were divided into three groups: symmetric loaders, underloaders, and overloaders. A 2 × 3 (limb × group) ANOVA was used to compare CCIs between limbs in all groups. A partial Spearman's test was performed to examine the association between CCIs ratios and pMCF. The CCIs of the vastus lateralis-lateral gastrocnemius muscle pair was higher in the involved limb of underloaders (vs. the uninvolved limb and vs. the involved limb of symmetric loaders). The ratio of M:L CCIs was significantly lower (more lateral CCIs) in the involved limb, which was associated with lower pMCF. These results suggest that individuals early after ACLR who walk with higher CCIs of lateral knee musculature (vs. medial), have medial tibiofemoral underloading., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

After stroke, deficits in paretic single limb stance (SLS) are commonly observed and affect walking performance. During SLS, the hip abductor musculature is critical in providing vertical support and regulating balance. Although disrupted paretic hip abduction torque production has been identified in individuals post-stroke, interpretation of previous results is limited due to the discrepancies in weight-bearing conditions. Using a novel perturbation-based assessment that could induce SLS by removing the support surface underneath one limb, we aim to investigate whether deficits in hip abduction torque production, vertical body support, and balance regulation remain detectable during SLS when controlling for weight-bearing, and whether these measures are associated with gait performance. Our results showed that during the perturbation-induced SLS, individuals post-stroke had lower hip abduction torque, less vertical stiffness, and increased frontal plane angular impulse at the paretic limb compared to the non-paretic limb, while no differences were found between the paretic limb and healthy controls. In addition, vertical stiffness during perturbation-induced SLS was positively correlated with single support duration during gait at the paretic limb and predicted self-selected and fast walking speeds in individuals post-stroke. The findings indicate that reduced paretic hip abduction torque during SLS likely affects vertical support and balance control. Enhancing SLS hip abduction torque production could be an important rehabilitation target to improve walking function for individuals post-stroke., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Published by Elsevier Ltd.)