Search

Abstract Electrical discharge machining is a significant non-traditional technique, widely used in the precise manufacturing field. However, the electrical discharge machining process possesses plenty of energy consumption and hazardous exhaust emissions. Since a sustainable machining technique, external magnetic field assisted, could dramatically develop sustainable machining performance of electrical discharge machining process, this paper presents a comparative study energy efficiency and environmental impact in magnetic field assisted electrical discharge machining and conventional electrical discharge machining. A novel thermo-physical model was proposed to calculate energy distribution under the single/continuous discharge, which was verified by a series of corresponding experiments. Then, based on simulation and experimental methods, a comparative study on the magnetic field assisted electrical discharge machining and conventional electrical discharge machining was conducted to analyze the discharge energy flowing and temperature distribution of workpiece, electrode tool and debris. Moreover, the effects of external magnetic field on the machining performance, environmental impacts and energy efficiency were presented. Eventually, it can be found out that the effect of magnetic field contributes to increasing energy utilization efficiency by 15.2%, material erosion efficiency by 22.6%, and material removal rate by 21.9%. To balance energy efficiency and surface roughness (Ra), the optimal parameter combination is obtained as below: magnetic field intensity: 0.2T, discharge current: 7–9A, and pulse duration: 300s. Highlights • Magnetic field assisted EDM improve energy efficiency and environmental impact. • A thermo-physical model is proposed to calculate energy distribution of MF-EDM process. • Sustainable machining performance of EDM and MF-EDM are comparatively investigated. • The optimal parameter is: magnetic field intensity: 0.2T, current: 7∼9A, and pulse duration: 300μs. [ABSTRACT FROM AUTHOR]

Dielectric medium (kerosene) between the tool electrode and workpiece forms a reaction product, owing to thermal effect of discharge in the process of electrical discharge machining (EDM), which is emitted from the surface in the form of harmful gas and may get into the operator's body by breath system inhalation and contact with skin. Therefore, exhaust emissions should be considered as important performance indicators for the green machining in the process of EDM. Moreover, energy efficiency and machining productivity should be improved and the cut process must take ecological constraints into consideration. Thereafter, the definition of green manufacturing helps to evaluate different and sometimes conflicting aspects of the manufacturing process, such as machining productivity, surface quality, energy efficiency and exhaust emissions. But it is difficult to dynamically adjust the weights of different aspects according to the actual processing conditions. This paper proposes a framework for optimization of cutting parameters to minimize energy consumption and exhaust emissions during electrical discharge machining of Al 6061 and SKD 11. Three cutting process parameters (peak current, pulse period, and duty cycle) are tested against material remove rate (MRR), surface roughness (Ra), energy efficiency per volume (EEV), and exhaust emissions characteristics (EEC) for EDM of these two materials. First, the process energy and exhaust emissions are analyzed. The results show that EEV is negatively correlated with surface quality (Ra) for both Al 6061 and SKD 11 material. Second, two data analyses (Taguchi and adaptive-network-based fuzzy inference system (ANFIS) analyses) are utilized to obtain high MRR and best Ra, EEV and EEC for the desired machining performances and environmental sustainability. It is found that the relative errors between the predicted values and experimental results of MRR, Ra, EEV and EEC are all not more than 20%, and found that the maximum of mean relative errors of them is 13.04%. Finally, a framework implemented by an optimization system, based on ANFIS, enhanced cuckoo search (ECS) algorithm and desirability function, is built to obtain the desired cutting parameters. It is found that high peak current (8.94A) and pulse period (500 μ s) are recommended to obtain multi-objective optimization for machining Al 6061, and that the optimal solutions of the EEV and EEC are significantly decreased, by 87.13% and 37.09%, respectively. Similarly, high peak current (8.77A) and pulse period (261.5 μ s) are recommended to obtain multi-objective optimization for machining SKD 11, and the optimal solutions of the EEV and EEC are significantly decreased, by 93.73% and 46.85%, respectively. Thereafter, it can be concluded from the above research that the proposed technique offers significant advantages and potential for applications in the green manufacturing field. Image 1 • Energy efficiency per volume was negatively correlated with Ra. • Maximizing energy efficiency and minimizing exhaust emissions by empirical models were obtained. • Balancing the machining performances and environmental sustainability was considered. • An optimization system with manual multi-objective weights was build. • Green regions of exhaust-friendly and energy-friendly were acquired. [ABSTRACT FROM AUTHOR]