Search

The construction of the first generation of commercial hybrid solar gas-turbine power plants will present the designer with a large number of choices. To assist decision making, a thermoeconomic study has been performed for three different power plant configurations, namely, simple- and combined-cycles along with a simple-cycle with the addition of thermal energy storage. Multi-objective optimization has been used to identify Pareto-optimal designs and highlight the trade-offs between minimizing investment costs and minimizing specific C02 emissions. The solar hybrid combined-cycle power plant provides a 60% reduction in electricity cost compared to parabolic trough power plants at annual solar shares up to 20%. The storage integrated designs can achieve much higher solar shares and provide a 7-13% reduction in electricity costs at annual solar shares up to 90%. At the same time, the water consumption of the solar gas-turbine systems is significantly lower than conventional steam-cycle based solar power plants. [ABSTRACT FROM AUTHOR]

A dynamic simulation model of a hybrid solar gas-turbine power plant has been developed, allowing determination of its thermodynamic and economic performance. In order to examine optimum gas-turbine designs for hybrid solar power plants, multiobjective thermoeconomic analysis has been performed, with two conflicting objectives: minimum levelized electricity costs and minimum specific CO2 emissions. Optimum cycle conditions: pressure-ratio, receiver temperature, turbine inlet temperature and flow rate, have been identified for a 15 MWe gas-turbine under different degrees of solarization. At moderate solar shares, the hybrid solar gas-turbine concept was shown to provide significant water and CO2 savings with only a minor increase in the levelized electricity cost. [ABSTRACT FROM AUTHOR]

Hybrid solar micro gas-turbines are a promising technology for supplying controllable low-carbon electricity in off-grid regions. A thermoeconomic model o f three different hybrid micro gas-turbine power plant layouts has been developed, allowing their environmental and economic performance to be analyzed. In terms of receiver design, it was shown that the pressure drop is a key criterion. However, for recuperated layouts, the combined pressure drop of the recuperator and receiver is more important. In terms of both electricity costs and carbon emissions, the internally-fired recuperated micro gas-turbine was shown to be the most promising solution of the three configurations evaluated. Compared to competing diesel generators, the electricity costs from hybrid solar units are between 10% and 43% lower, while specific CO2 emissions are reduced by 20-35% . [ABSTRACT FROM AUTHOR]

A thermoeconomic model of a novel hybrid solar gas-turbine power plant with an air-based bottoming cycle has been developed, allowing its thermodynamic, economic, and environmental performance to be analyzed. Multi-objective optimization has been performed to identify the trade-offs between two conflicting objectives: minimum capital cost and minimum specific CO2 emissions. In-depth thermoeconomic analysis reveals that the additional bottoming cycle significantly reduces both the levelized cost of electricity and the environmental impact of the power plant (in terms of CO2 emissions and water consumption) when compared to a simple gas-turbine power plant without bottoming cycle. Overall, the novel concept appears to be a promising solution for sustainable power generation, especially in water-scarce areas. [ABSTRACT FROM AUTHOR]

Liberalized electricity market conditions and concentrating solar power technologies call for increased power plant operational flexibility. Concerning the steam turbine (ST) component, one key aspect of its flexibility is the capability for fast starts. In current practice, turbine start-up limitations are set by consideration of thermal stress and low cycle fatigue. However, the pursuit of faster starts raises the question whether other thermal phenomena can become a limiting factor to the start-up process. Differential expansion (DE) is one of such thermal properties, especially since the design of axial clearances is not included as part of start-up schedule design and because its measurement during operation is often limited or not a possibility at all. The aim of this work is to understand DE behavior with respect to transient operation and to quantify the effect that such operation would have in the design and operation of axial clearances. This was accomplished through the use of a validated thermomechanical model that was used to compare DE behavior for different operating conditions of the machine. These comparisons showed that faster starts do not necessarily imply that wider axial clearances are needed, which means that the thermal flexibility of the studied turbine is not limited by DE. However, for particular locations, it was also obtained that axial rubbing can indeed become a limiting factor in direct relation to start-up operation. The resulting approach presented in this work serves to avoid over-conservative limitations in both design and operation concerning axial clearances. [ABSTRACT FROM AUTHOR]

In order to improve the startup flexibility of steam turbines, it becomes relevant to analyze their dynamic thermal behavior. In this work, the relative expansion between rotor and casing was studied during cold-start conditions. This is an important property to monitor during startup given that clearances between rotating and stationary components must be controlled in order to avoid rubbing. The investigation was performed using a turbine thermal simplified model from previous work by the authors. The first step during the investigation was to extend and refine the modeling tool in order to include thermomechanical properties. Then, the range of applicability of the model was validated by a twofold comparison with a higher order finite element (FE) numerical model and measured data of a cold start from an installed turbine. Finally, sensitivity studies were conducted with the aim of identifying the modeling assumptions that have the largest influence in capturing the correct thermal behavior of the turbine. It was found that the assumptions for the bearing oil and intercasing cavity temperatures have a large influence ranging between ±25% from the measured values. In addition, the sensitivity studies also involved increasing the initial temperature of the casing in order to reduce the peak of differential expansion. Improvements of up to 30% were accounted to this measure. The studies performed serve as a base toward further understanding the differential expansion during start and establishing future clearance control strategies during turbine transient operation. [ABSTRACT FROM AUTHOR]

Solar steam turbines are subject to high thermal stresses as a result of temperature gradients during transient operation, which occurs more frequently due to the variability of the solar resource. In order to increase the flexibility of the turbines while preserving lifting requirements, several operational modifications for maintaining turbine temperatures during offline periods are proposed and investigated. The modifications were implemented in a dynamic thermal turbine model and the potential improvements were quantified. The modifications studied included: increasing the gland steam pressure injected to the end-seals, increasing the back pressure and increasing the barring speed. These last two take advantage of the ventilation and friction work. The effects of the modifications were studied both individually as well as in different combinations. The temperatures obtained when applying the combined modifications were compared to regular turbine cool-down (CD) temperatures and showed significant improvements on the startup times of the turbine. [ABSTRACT FROM AUTHOR]