Search

Abstract: Due to the unique properties of amphiphilic Pluronic block copolymers, they have been blended with other polymers such as PVDF to prepare membranes. Considering the stability issue, the strong pore-forming ability of Pluronic F127, and the mechanical strength of the resultant membranes, Pluronic/LiCl mixed additive consisting of a very low concentration of Pluronic has been used in this study. The effects of spinning conditions on PVDF hollow fiber fabrication have also been studied. It is found that the use of merely 0.2wt% of Pluronic is sufficient to impose significant impacts on the morphology, filtration performance, and mechanical properties of the resultant fibers. Hollow fibers spun using higher coagulant temperature, higher take-up speed, and water as the bore fluid exhibit better mechanical properties and filtration performance. PVDF hollow fiber membranes with PWP of 1180L/m2 hMPa and MWCO of 5kDa were obtained when spun with optimized spinning conditions and using 3wt% of LiCl and 0.2wt% of Pluronic as the mixed additive. The fibers can withstand a pressure of 0.55MPa from the lumen. [Copyright &y& Elsevier]

This report demonstrates the fabrication of a composite hollow fiber membrane that efficiently recovers dissolved methane (dCH 4) from anaerobic wastewater treatment effluents via membrane contactor (MC) process. We first fabricated highly porous hollow fiber membranes (∼85% porosity) using polyvinylidene difluoride (PVDF). Then, we coated the whole structure (bulk), or lumen side of PVDF supports with polydimethylsiloxane (PDMS), a hydrophobic polymer possessing high gas permeability. The adjustment of the concentration of PDMS precursor mix could effectively serve for tuning the performance characteristics of MC membranes and helped suppress membrane wetting, a major performance-reducing factor. Despite their denser skin layers, the lumen-modified membranes demonstrated superior dCH 4 recovery flux. Mass transfer analyses have confirmed the importance of preserving bulk porosity while coating the membrane surfaces. The long-term performance tests performed using actual anaerobic effluents suggested that the PDMS coating did not accelerate fouling, such that the lumen-modified MC membranes showed an almost steady flux for 8 days with an anaerobic membrane bioreactor effluent. A high-strength effluent, obtained from an up-flow anaerobic sludge blanket reactor, induced faster fouling. However, we observed only a ∼20% flux decline in a 10-day operation. Thus, we propose that the designed PDMS-PVDF composite membranes are promising for industrial practices. Image 1 • We prepared PDMS-coated PVDF porous hollow fiber membranes for membrane contacting. • Both lumen- and bulk-modified PVDF membranes were successful in methane recovery. • Lumen-modified PDMS-PVDF membrane outperformed commercial PP and PDMS membranes. • Lumen-modified PVDF achieved long-term performance with actual anaerobic effluents. [ABSTRACT FROM AUTHOR]

Abstract The combination of nonsolvent and thermally induced phase separation (N-TIPS) method has shown promising ability in harvesting the features from the nonsolvent induced phase separation (NIPS) and thermally induced phase separation (TIPS) processes for developing membranes with a tailorable surface pore structure. However, previous approaches have been subjected to either the formation of macrovoids or dense layer due to the dominant NIPS effect, or required sophisticated instruments and operation skills. In this work, a facile attempt was carried out to fabricate novel polyvinylidene fluoride (PVDF) hollow fiber membranes with tunable surface pore structure while maintaining the narrow pore size distribution and mechanical strength. A modified N-TIPS method was developed by using mixed diluents: dimethyl phthalate (DMP) as a water-immiscible poor solvent for TIPS process, and triethyl phosphate (TEP) as a water-miscible neutral solvent to bridge the TIPS and NIPS processes. To further control the membrane formation especially near the membrane surface, an amphiphilic additive Pluronic F127 was also added as a potential pore-former and surface hydrophilicity modifier. PVDF hollow fiber membranes with a highly porous structure and a narrow pore size distribution were successfully synthesized by using TEP and Pluronic F127 in the N-TIPS process. The mechanism of N-TIPS process was thoroughly discussed. The water permeability of the membrane increased significantly from 389 ± 30–922 ± 36 L m–2 h–1 bar–1, with overall porosity improved from 50 ± 2.2–69 ± 2.9%, and a mean pore size of ~ 0.18 µm. The membranes produced by N-TIPS method also exhibited a good tensile strength ranging from 5.6 ± 0.1–6.5 ± 0.2 MPa, showing a great potential for a broad range of water applications after further modifications. Besides, the formation of piezoelectric β-phase crystals of the PVDF membrane was observed when the mixed diluent was used, which sheds light on the possible applications of resultant membranes in electrochemical separation process. Highlights • PVDF hollow fiber membranes were developed via a modified N-TIPS method using mixed diluents together with Pluronic F127. • The NIPS effect could be induced at the outer surface with the co-occurrence of TIPS process along the bulk of membrane. • The surface pore structure of membrane could be tailored without the formation of mechanically weak macrovoids. • The prepared membranes possess a hydrophobic surface with good porosity, permeability and mechanical strength. [ABSTRACT FROM AUTHOR]