Search

Abstract Background The optimal internal fixation strategy for vertical femoral neck fractures (VFNFs) in nongeriatric patients remains uncertain. Therefore, the purpose of this study was to compare the clinical prognoses and underlying mechanical characteristics of a novel off-axis screw technique with dynamic hip screws (DHSs) and three traditional parallel screws. Methods This study included a clinical investigation and a patient-specific finite element analysis (FEA). In the clinical investigation, VFNF patients were grouped by fixation type: (1) use of three parallel screws (G-TRI); (2) augmentation with an off-axis screw (G-ALP); and (3) DHS with an anti-rotational screw (G-DHS). Fixation failures (nonunion, femoral neck shortening (FNS), varus deformation, screw cut-out) and avascular necrosis (AVN) consequent to the three types of fixations were compared. In the FEA, twenty-four fixation models with the three fixation types were created based on the data of eight healthy volunteers. Models were assessed under walking conditions. Stiffness, interfragmentary motion (IFM), and implant stress were evaluated. Results In the clinical investigation, the fixation failure rate was significantly (p < 0.05) lower in G-ALP (18.5%) than in G-DHS (37.5%) and G-TRI (39.3%). No significant difference in AVN was observed among the three fixation groups. In the FEA, stiffness and implant stress in the G-DHS models were significantly (p < 0.05) higher, and the IFM of G-ALP was significantly (p < 0.05) lower among the groups. Conclusions Among fixation types for VFNFs, the off-axis screw technique exhibited better interfragmentary stability (lowest IFM) and a lower fixation failure rate (especially FNS). Analyzing interfragmentary stability in biomechanical experiments is more consistent with clinical prognosis than construct stability for VFNFs, suggesting that internal fixations should aim for this outcome.

Abstract Background Free vascularized fibula graft (FVFG) techniques have most consistently demonstrated beneficial effects in young patients diagnosed with nontraumatic osteonecrosis of the femoral head (NONFH), and the core track technique (CTT) in particular is the most commonly used technique. As an alternative to CTT, the modified light bulb technique (LBT) has been reported to have a higher success rate. However, its biomechanical outcomes are poorly understood. This study aimed to compare the biomechanical properties of modified LBT with those of CTT in treating NONFH. Methods Two types (C1 and C2) of NONFH finite element models were established on the basis of a healthy subject and the Japanese Investigation Committee (JIC) classification system, and the CTT and LBT procedures were simulated in each type of model. The average von Mises stresses and stiffness of the proximal femur were calculated by applying a load of 250% of the body weight on the femoral head to simulate walking conditions. In addition, two patient-specific models were built and simulated under the same boundary conditions to further validate the LBT. Results In the healthy subject-derived models, both the LBT and CTT resulted in reduced stresses in the weight-bearing area, central femoral head, femoral neck, and trochanteric and subtrochanteric regions and increased structural stiffness after surgery. In the weight-bearing area, the CTT reduced the stress more than the LBT did (36.19% vs 31.45%) for type C1 NONFH and less than the LBT did (23.63% vs 26.76%) for type C2 NONFH. In the patient-specific models, the stiffness and stresses also increased and decreased, respectively, from before to after surgery, which is consistent with the results of healthy subject-derived models. Conclusion The biomechanical effects of the LBT and CTT differ by the JIC type of NONFH. In terms of preventing the collapse of the femoral head, the LBT may be more effective for JIC type C2 NONFH and may be a suitable alternative to the CTT, while for JIC type C1 NONFH, the CTT is still a better choice. Both techniques can improve the biomechanical properties of NONFH by reducing the proximal femoral stress and increasing the structural stiffness.

Abstract Background The position of Kirschner wires (K-wires) has an influence on the outcome of modified tension-band wiring (MTBW) in fixing patella fractures. However, the instruction for K-wires positioning is not clear enough. This study tried to clarify the effect of K-wires positioning and provide evidence for a more definite instruction. Methods The sagittal position (SP) suitable for placing K-wires was evenly divided into SP 1–5 from anterior to posterior, and the finite element models of midpatella transverse fractures fixed by the figure-of-eight or figure-of-zero MTBW were built up at each SP. Separating displacement of the fracture, stress of the fracture, and stress of the internal fixations were measured at 45° knee flexion by using finite element analysis. Results The separating displacement of the fracture was smaller at SP 3–5 (23% smaller than SP 1–2). From SP 1 to 5, the compression of the fracture surfaces increased (R = 0.99, P = 0.001); the improper stress area of the fracture surfaces decreased (R = − 0.96, P = 0.01), and so was the stress of K-wires (R = − 0.93, P = 0.02). However, the stress of stainless steel wires showed a stable trend. Conclusions The SP of K-wires plays a role in the function of MTBW in the surgical management of transverse patella fracture. At 45° knee flexion, posteriorly placed (close to the articular surface) K-wires enable optimal stability and stress for the fracture, which provides basis for the positioning of K-wires in clinical practice.