Search

The interface force condition on the cross section of parallel steel wire strands is an important basis for studying the longitudinal friction and slip behavior of wires. In this study, force-chain superposition was proposed to solve the transmission and distribution of transverse forces between parallel wires. The calculation rules for the basic parameters in the solution were determined, and a wire-drawing experiment was designed to verify their applicability. A two-dimensional discrete model corresponding to the cable cross section was established. According to the source and characteristics of the transverse load, the force system is decomposed into two directions to form two force chain analysis paths so that the model assumptions can be applied properly. A recursive algorithm was proposed to solve the two force chains, and symmetry conditions were applied at the coupling position to make the system self-consistent. The normal forces acting on the interface points were obtained by superimposing the results onto the two force chains and were verified against finite element analysis (FEA) results. A long-span cable-stayed bridge was considered as an example to investigate the interface force condition of its cables, based on which the approximate development length of the broken wires and the interface extrusion force of the multilayered beam model were established. The results indicate that the slight twisting of the parallel wire strands under the action of a large cable force provides 85% of the total interface forces, and the normal force is significantly concentrated in the central area of the cross section. The approximate development length of the central wire is only 25.9% of that of the outermost wire, and the minimum slip friction force between the layers accounts for only 21.2% of the maximum value for the multilayered beam model, confirming that the interface force condition has a significant impact on the longitudinal friction and slip behavior of cable wires. [ABSTRACT FROM AUTHOR]

The continuous increase in traffic volume requires wider single box girders for long-span cable-supported bridges. Flutter and aerostatic instability are challenging issues for these flexible bridges, especially when they are located in typhoon-prone regions. Aerodynamic countermeasures such as vertical and horizontal stabilizers, which are convenient in operation, saving in cost, and effective in the enhancement of flutter performance, are usually employed to withstand the wind environment requirement. This study investigates the aerodynamic and aerostatic effects of upper central vertical stabilizers (UCVS), lower central vertical stabilizers (BCVS), horizontal stabilizers (HS), and their combinations on two wide single box girders with an aspect ratio larger than 12 at various angles of attack (AOAs). The optimal layouts of stabilizers for the enhancement of flutter performance are studied using a series of wind tunnel tests. Their control mechanisms are examined and discussed using flutter derivatives and step-by-step (SBS) method. A new index of nominal torsional center (NTC) is proposed to intuitively describe the flutter modality. The correlations among different indexes of flutter modality, flutter derivatives, and Ucr are further analyzed. The static coefficients of the bridge girders and the aerostatic performance of the bridge with or without stabilizers are also analyzed. Experiment results show that the values of Ucr for 4- and 5-m-high single box girders increased by 13.9% and 46.3%, respectively, after the hybrid installation of UCVS, BCVS, and HS at their optimal conditions. The analytical solutions indicate that the installation of different stabilizers changes the variation trend of the aerodynamic damping ratio with the wind speed to increase or reduce the flutter boundary. Four flutter modality indexes including amplitude ratio (Ψ), phase difference (ψ), energy participation level (Ph), and NTC are all found that have no obvious correlations with Ucr. The static analysis on a three-dimensional bridge showed that the optimal stabilizer schemes for flutter have insignificant effects on aerostatic performance. [ABSTRACT FROM AUTHOR]

Considering the socioeconomic prominence of long-span cable-stayed bridges, it is important to ensure their normal operation after strong earthquake events. To this end, their seismic performance must be based on a proper understanding of the relationship between structural capacity and seismic demand. However, evaluating the seismic demands on cable-stayed bridges is challenging due to relatively long distances between supports and the complex composition of various structural elements. The large dimension in the horizontal direction inevitably leads to incoherent input ground motions at supports, while various structural components such as cables, decks, and pylons make it difficult to define the system's performance limit-state or capacity using a single index or function. This work presents three main contributions to properly assess the seismic performance of a long-span cable-stayed bridge. First, an algorithm was proposed to generate a set of bidirectional spectrum-compatible ground motions for the multiple supports of a bridge. Second, two performance measures were proposed to quantitatively assess the seismic demands and capacity of a cable-stayed bridge: probabilistic comparison index and axial force-bending moment (PM) safety factor. Third, the impacts of the seismic motions on the long-span cable-stayed bridge were thoroughly examined using eight different scenarios in terms of the three aspects: (1) multisupport excitation, (2) assumed soil class, and (3) wave passage effect. For this purpose, the Incheon Grand Bridge was chosen as a reference structure. This bridge has a central span of 800 m and a total length of 1,480 m. The results demonstrate that the seismic demands of the long-span cable-stayed bridge vary along with different conditions of seismic motions, and the proposed performance measures and ground motion-generating algorithm enable quantitative investigation of the impact of different conditions on the long-span cable-stayed bridge. [ABSTRACT FROM AUTHOR]

Typhoon winds near the external eye wall of a strong typhoon are extremely nonstationary and disastrous due to its vortex and convective origin as well as its high wind speeds. However, typhoon-induced nonstationary responses of long-span bridges are currently analyzed with the assumption of time-invariant wind coherence. By taking the Stonecutters cable-stayed bridge in Hong Kong under Typhoon Hato in 2017 as an example, this paper presents the time-varying wind spectra and coherences for the bridge based on the wind data recorded by the multiple anemometers installed on the bridge. The analytical framework for nonstationary buffeting analysis of long-span bridges under typhoon winds is enhanced by considering time-varying wind coherence and applied to the Stonecutters Bridge under Typhoon Hato. The computed responses are compared with the field measurement responses. The comparative results demonstrate the feasibility and accuracy of the enhanced framework for buffeting analysis of long-span bridges with time-varying wind spectra and coherences. Comparative results with the other two cases of time-invariant coherence functions also highlight the importance and necessity of considering the time-varying wind coherence in the nonstationary buffeting analysis of long-span bridges under typhoon winds. [ABSTRACT FROM AUTHOR]