Search

In this study, the elastomer cover, a new contact material, was developed to establish the customized ultrasonic measurement considering surface irregularities of stone cultural heritages. The cover exhibits high elastic force and wear resistance because it has tensile strength of 17MPa and elongation of 625%. In addition, as a result of comparative experiments for the seven types according to transducers and contact materials including the elastomer cover, rock surface irregularities significantly affect attenuation of ultrasonic velocity. The phenomenon was more noticeable in the chiseling finish and indirect transmission measurement rather than the dabbed finish and direct transmission measurement. However, the Type F using the exponential transducer and elastomer cover showed stable P-wave velocity and high amplitude regardless of the surface irregularities. This because the elastomer cover sufficiently sticks to surface irregularities and removes pores between a transducer and a rock specimen. Therefore, the Type F should be used for the ultrasonic measurement of stone cultural heritages with surface irregularities.

As the Seated Iron Buddha Statues, Vairocana Buddha of Dopiansa Temple in Cheolwon, Nosana Buddha of Samhwasa Temple in Donghae and Sakyamuni of Mangisa Temple in Pyeongtaek were made during Unified Silla to Koryo Dynasty. These are damaged degradation which are crack, break-out, peel off and various pollutant. As a result of deterioration evaluation using radiography, crack, gap, break-out, pore space and restoration material are confirmed inside in the Buddha Statues. Based on iron strength, the Buddha Statues will be maintain current state as long as a high external impact is not applied. Also, iron core and nails used for fixing of internal and external framework were observed in the Buddha Statues. According to prominent line of surface, embossed inscription, hands cast separately and combined, the Buddha Statues were made by using division casting.

This study is to interpret the construction characteristics and the provenance of soil layers from the Dongnamri site in Baekje Kingdom of Buyeo, Korea. The soil layers is divided into present age layer, Baekje layer and lower part layer, and the soils formed in the Baekje Kingdom period is divided into the Baekje 1st layer and the Baekje 2nd layer according to temporal intervals. The soil layers gradually becomes darker in color and higher in mineral content towards the lower part layer. However, the particular distinction between layers of the soils could not be identified. Additionally, the soil layers show a similar characteristics of mineralogy and geochemical evolution regardless of the layers. This indicates that the sites were made with weathered soil from an identical bed rock, and the site show a similarity to the surrounding soil, indicating its possibility of being the original materials. However, through the analysis of particle size, the first and second Baekje layers occurred that these layers were formed by setting up the soil with high content of sand on the bottom and stacking the soil with high content of silt on top of it.

The wooden Ksitigarbha Triad Statues (Treasure No. 1749) of Shinhungsa temple in Sokcho are enshrined in the inside of the Myeonbujeon Hall. The Statues are highly damaged physical weathering which are crack and exfoliation. Also, the Statues were deteriorated by chemical and biological weathering. This study carried out nondestructive method as deterioration map, ultrasonic measurement, X-ray and endoscopy survey for deterioration evaluation and conservation plan. As a result, Ksitigarbha Statue coated by dust and various pollutants. And gold-gilt of Statue`s surface has peeled off. Head part of Mudokguiwang Statue was discolored from water leak in Myeongbujeon Hall. Domyeongjonja Statue is highly damaged by insects. Result of endoscopy, there were bee hives in the inside of the Statue. Therefore, we suggest that these Statues have need to do conservation treatment on the basis of diagnostic results.

This study focused on making technique and usage of potteries from Proto-Three Kingdom to Baekje Kingdom in Balanri Site. The potteries were divided into four groups, Jungdo type I, Jungdo type II, Tanalanmun type and the Baekje type on the basis of the shape and physical properties. The Jungdo type potteries were used as kitchen wares, showing mostly yellowish brown color. The Tanalanmun type potteries were used as storages, showing gray green color. Firing temperature of the Jungdo type and the Baekje type potteries were presumed to be fired at 900 to , whereas the Tanalmun type potteries were fired at around 900 to . This is indicated that the firing condition was adjusted according to the purposes of the potteries. On the one hand, the Balanri potteries were made of paleo-soil which was collected in very near place from the site based on geochemical characteristics of the pottery clays and the soil.

The purpose of this study were to interpret making characteristics and clay sources for Proto-Three Kingdoms period potteries which were excavated from Bakjimeure site in Tangjeong, Asan, Korea, on the basis of shape types. The pottery samples of the studied included deep bowl pottery, cylinder shaped pottery, duck shaped pottery and rounded based jar with short neck. And the last jar was dominant among them. This is supported in nearby Yongduri Jinter site, Galmaeri site and Baekseokdong site. They vary in terms of color of clay, absorption ratio and mineral classification. Based on the fact that their absorption ratio range was 4.50 to 25.19% and firing temperature range was 850 to , they were thought to be widely used. The equivalence of cylinder shaped pottery, duck shaped pottery and deep bowl pottery was high in terms of material characteristics and their firing temperature range was 850 to . However, the deep bowl pottery, compared to other pottery shapes, contained great amount of coarse grained quartz and feldspar, and was different from others in terms of function. For soil sample collected from relative plains (area 3) in the southernmost part of the site, their mineralogical and geochemical characteristics were the most similar to those of the potteries excavated from the Bakjimeure site and even most of the potteries collected from different sites.

The Hongjimun Ogansumun (Five-arched floodgates) is composed mainly of biotite granite, pink feldspar granite and granodiorite that are very similar with granitic rocks around the Seoul. Main damage in the floodgates was gray, yellow and predominantly white discoloration on the surface of stone blocks. All floodgates showed more discoloration in the wall than ceiling, and there were growing stalactite on the ceiling. Scientific analyses determined that the white discoloring substrates were mainly calcite. Therefore, conservation treatment was carried out to remove the substrates by using dry cleaning, high pressure cleaning and chemicals. The floodgates have been restored to good state, but it is still significantly necessary to install drainage on the top of the gates.

The Clay Statues of Donggwanwangmyo Shrine (Treasure No. 142) are highly damaged physical weathering which are crack, exfoliation. Pigment of surface are discolored by chemical weathering like dust. The result of ultrasonic velocity measurement, low velocity zone was measured the lowest part of Woojanggun Statue. Deficiency condition of pigment layer was evaluated quantitatively through infrared Thermography. As a result, exfoliation part was detected at high temperature. Making techniques of the Clay statues were identified by gamma rays, infrared TV, SEM. All Clay Statues were founded on wood base and joints of wood were fixed using thin iron wires. After wood base was twisted a straw rope, it was made by clay. Clay was blended with rice straw to prevention of crack and exfoliation. The upper side of clay layer was coated with Hanji(Korean handmade paper) and cotton in order to isolate the pigment layer.

This study focused on analysis condition and application method of the passive infrared thermography according to the direction and time to nondestructively detect the blistering zone of stone cultural heritage. As a result, the passive thermographic images showed different temperature characteristics by time because it sensitively reacts to air temperature, insolation and sunshine direction. In particular, the insolation and sunshine direction, which are periodically changed from 6:00 to 17:00, irregularly made surface temperature. In addition, surface temperature differences were brought on fresh zones and blistering zones except specific time since blistering causes erratic thermal transfer. As a result of examining the detection characteristics of blistering by time, the blistering was well detected between 9:00 and 10:00 when there was rapid increase in air temperature and insolation in all direction except the north. However, this study isn`t considered effects of four seasons because it is carried out in autumn, and the passive thermography has difficulty to analyze the quantitative area of blistering zone. Therefore, an additional study for synthetic consideration of the passive thermography analysis about four seasons and quantitative modeling of blistering zone using the active thermography are needed.

This study was interpreted the making techniques of the Four Guardian Statues in Wanju Songkwangsa Temple, and retained basic data necessary for conservation treatment and restoration of the same material by estimating the soil source. The molding clay used in the Statues showed a variety of material characteristics according to different layers. The first and mid layers estimated as the original molding clay are composed of the same kind of soil. The soil of the finish layer was also confirmed to be genetically similar to that of the first and mid layers, despite little discrepancy. The former restoration layer was inconsistent in material characteristics with the original molding clay in every result of analysis. As a result of gamma radiography, making techniques of the Statues were able to identify the figure of the frame connecting the woods of main pillar frame to sub-frame and steel wire with ㄷ-clamp, nails and straw ropes, and the molding clay constructed upon the frame. Meanwhile, provenance interpretation confirmed that the soil of the estimated provenance area is of the same origin as the soil of the finish layer, and therefore is an appropriate material for conservation treatment. This result will contribute to the research on making techniques of the molding clay Statues.

The Myeongdongseongdang Cathedral, which was designated as Historic Site No. 258 in Korea, is a representative cathedral of Korean Catholic church designed by a French priest Eugene-Jean Georges Coste and completed in 1898. It is a Gothic-styled architecture constructed with bricks and stones. Lithological and mineralogical analyses determined that holy stone relics were made of marble and granite, and foundation stones are of pink feldspar granite. Deterioration mapping and ultrasonic measurement revealed main weathering and damage were exfoliation (40%) and black discoloration (37%) in the holy water basin, and exfoliation (6%) and discoloration (46%) in the exterior foundation stones. Ultrasonic velocity of the stones were calculated as 3,525m/s in the holy water basin and 2,795m/s in the exterior stones that indicated these stones were sorted into moderately to highly weathered rock. This was resulted from moisture and atmospheric pollutants around the cathedral.

Nondestructive deterioration diagnosis has been carried out for the former ore dressing plant of the Yongwha mine in Yeongyang (Registered Cultural Property No. 255). Deterioration rates about organic contaminant and soil of the upper part (7 to 13 layer) indicate higher than the lower part (1 to 6 layer) of the ore dressing plants. By contrast, deterioration rates such as crack, break out and discoloration of the lower part indicate very higher than the upper part. It is estimated that the plants of the lower part that mechanical and chemical process had been done for flotation were damaged severely by physicochemical weathering with reaction of concrete and chemical solution. As results of ultrasonic velocity measurement, average p-wave velocity of plants were measured 2,462m/s (compressive strength ). As for the analytical results of surface contaminants and soil compositions using P-XRF, they were identical with major elements (Cu, Zn, Pb, Fe and As) of ore minerals from the Yongwha mine. Therefore, the ore dressing plant should be treated by phytoremediation with conservation because heavy metals could impinged upon plants and natural environment.

The major petroglyphs of Bangudae site were composed mainly of hornfelsed shale. Surface of the rock was formed weathering layer (average porosity 25%) that discriminated mineral and chemical composition against fresh rock (average porosity 0.4%). The lost area of major petroglyphs in the past up images carved to the present was calculated about 23.8%. And occurrence area of exfoliation indicated 1.2% of the whole petroglyphs. As a result of the chromaticity analysis, color of the major petroglyphs was changed brighter and yellower than fresh rock by chemical and biological weathering factors. Average ultrasonic velocity of petroglyphs was measured 2,865m/s. This result indicated that ultrasonic velocity decreased especially bottom of petroglyphs than measured result in 2003 year. The results of the evaluation for slope stability, it identified the possibility of toppling, planar and wedge failure in host rock. The 3D image analysis and modeling data of the cavern obtained for structural reinforcement.

The Usuki Stone Buddha Statues in Oita are consisted of 60 Buddhas which represent of Japan carved on the rock-cliff in the 12 to 14th centuries. The basement rock of the statues is dark gray welded lapilli tuff that containing the Aso-4 pyroclastic rock group. Deterioration maps for the Hoki I and the Furuzono Buddha Statues group show multi-directional fissures on the Cakra, and sheeting-off zone at the margin of uprising water. Deterioration rate of the Hoki I group was calculated fissure about 121 in number, 19% of sheeting-off zone and 51% of biological weathering in surface of area. And the Furuzono group was also evaluated as about 48 of fissures in number, 24% of sheeting-off zone and 41% biological weathering. The slope stability assessment results, the Hoki I developed discontinuous planes has possibility of planar, toppling and wedge failures in all caves. Ultrasonic velocity of the Aizen-myooh (basement rock) ranges from 1,520 to 2,794 (average 2,298m/s). And pedestal of Amita-yeorae which has been replaced by new fresh rock is measured as 3,242 to 4,141 (average 3,813m/s). Therefore, we establish of planing conservation treatment and reinforcement methods to fissure, cavity, sheeting-off zone in the Buddha surface.

This study was to identify the material characteristics and provenance of the Joseon (the 15th to 17th century) potteries from Ssangyongdong Yongam site in Cheonan. The pottery samples of the kilns and the workshops (habitation) from the study area have grey or red color with similar matrix but various shapes and different hardness, according to firing temperature. All of the pottery and the workshop soils were very similar patterns with characteristics of occurrences, mineralogy and geochemical evolution trend. But soils from around the site does not correspond with them. So the workshop soil that the fine clay is raw clay for making pottery in Yongam site. Firing temperature of soft-type potteries were presumed to be formed around based on phase transition of clay minerals and mica. Hard-type pottery, mullite was detected and plagioclase was not detected by X-ray diffraction analysis, which means that potteries had experienced firing between 1,000 to .

This study was focused on digital restoration and surface depth modeling applying the three-dimensional laser scanning system of the Haeundae Stone Inscription. Firstly, the three-dimensional digital restoration carried out acquiring of point cloud using wide range and precision scanner, thereafter registering, merging, filtering, polygon mesh and surveyed map drawing. In particular, stroke of letters, inscribed depth and definition appearing the precision scanning polygon was outstanding compared with ones of the wide range polygon. The surface depth modeling completed through separation from polygon, establishment of datum axis, selection of datum point, contour mapping and polygon merging. Also, relative inscribed depth (5~17mm) and outline by the depth modeling was well-defined compared with photograph and polygon image of the inscription stone. The digital restoration technology merging wide range and precision scanning restored the total and detailed shape of the Stone Inscription quickly and accurately. In addition, the surface depth modeling visibly showed unclear parts from naked eye and photograph. In the future, various deteriorations and surrounding environment change of the Stone Inscription will be numerically analyze by periodic monitoring.