Search

In spite of the success of vertebroplasty (VP) and balloon kyphoplasty (BKP), which are widely used for stabilizing painful vertebral compression fractures, concerns have been raised about use of poly(methyl methacrylate) (PMMA) bone cements for these procedures since the high compressive modulus of elasticity (E) of the cement is thought to be one of the causes of the higher number of adjacent-level vertebral fractures. Therefore, bone cements with E comparable to that of cancellous bone have been proposed. While the quasi-static compressive properties of these so-called “low-modulus” cements have been widely studied, their fatigue performance remains underassessed. The purpose of the present study was to critically compare a commercial bone cement (control cement) and its low-modulus counterpart on the basis of quasi-static compressive strength (CS), E, fatigue limit under compression-compression loading, and release of methyl methacrylate (MMA). At 24 h, mean CS and E of the low-modulus material were 72% and 77% lower than those of the control cement, whereas, at 4 weeks, mean CS and E were 60% and 54% lower, respectively. The fatigue limit of the control cement was estimated to be 43–45 MPa compared to 3–5 MPa for the low-modulus cement. The low-modulus cement showed an initial burst release of MMA after 24 h followed by a plateau, similar to many other commercially available cements, whereas the control cement showed a much lower, stable release from day 1 and up to 1 week. The low-modulus cement may be a promising alternative to currently available PMMA bone cements, with the potential for reducing the incidence of adjacent fractures following VP/BKP.

Disease and injuries that affect the skeletal system may require surgical intervention and internal fixation, i.e. orthopedic plate and screw insertion, to stabilize the injury and facilitate tissue repair. If the surrounding bone quality is poor the screws may migrate, or the bone may fail, resulting in fixation failure. While numerous studies have shown that cement augmentation of the interface between bone and implant can increase screw pull-out force, the physical properties of cement that influence pull-out force have not been investigated. The present study sought to determine how the physical properties of high strength calcium phosphate cements (hsCPCs, specifically dicalcium phosphate) affected the corresponding orthopedic screw pull-out force in urethane foam models of "healthy" and "osteoporotic" synthetic bone (Sawbones). In the simplest model, where only the bond strength between screw thread and cement (without Sawbone) was tested, the correlation between pull-out force and cement compressive strength (R2 = 0.79) was weaker than correlation with total cement porosity (R2 = 0.89). In open pore Sawbone that mimics "healthy" cancellous bone density the stronger cements produced higher pull-out force (50-60% increase). High strength, low porosity cements also produced higher pull-out forces (50-190% increase) in "healthy" Sawbones with cortical fixation if the failure strength of the cortical material was similar to, or greater than (a metal shell), actual cortical bone. This result is of particular clinical relevance where fixation with a metal plate implant is indicated, as the nearby metal can simulate a thicker cortical shell, thereby increasing the pull-out force of screws augmented with stronger cements. The improvement in pull-out force was apparent even at low augmentation volumes of 0.5mL (50% increase), which suggest that in clinical situations where augmentation volume is limited the stronger, lower porosity calcium phosphate cement (CPC) may still produce a significant improvement in screw pull-out force. When the correlation strength of all the tested models were compared both cement porosity and compressive strength accurately predicted pull-out force (R2=1.00, R2=0.808), though prediction accuracy depended upon the strength of the material surrounding the Sawbone. The correlations strength was low for bone with no, or weak, cortical fixation (R2=0.56, 0.36). Higher strength and lower porosity CPCs also produced greater pull-out force (1-1.5kN) than commercial CPC (0.2-0.5kN), but lower pull-out force than PMMA (2-3kN). The results of this study suggest that the likelihood of screw fixation failure may be reduced by selecting calcium phosphate cements with lower porosity and higher compressive strength, in patients with healthy bone mineral density and/or sufficient cortical thickness. This is of particular clinical relevance when fixation with metal plates is indicated, or where the augmentation volume is limited.