Search

Cell size, measured as either volume or mass, is a fundamental indicator of cell state. Far more tightly regulated than size is density, the ratio between mass and volume, which can be used to distinguish between cell populations even when volume and mass appear to remain constant. Here we expand upon a previous method for measuring cell density involving a suspended microchannel resonator (SMR). We introduce a new device, the dual SMR, as a high-precision instrument for measuring single-cell mass, volume, and density using two resonators connected by a serpentine fluidic channel. The dual SMR designs considered herein demonstrate the critical role of channel geometry in ensuring proper mixing and damping of pressure fluctuations in microfluidic systems designed for precision measurement. We use the dual SMR to compare the physical properties of two well-known cancer cell lines: human lung cancer cell H1650 and mouse lymphoblastic leukemia cell line L1210. [ABSTRACT FROM AUTHOR]

We present a unique bubble generation technique in microfluidic chips using continuous-wave laser-induced heat and demonstrate its application by creating micro-valves and micro-pumps. In this work, efficient generation of thermal bubbles of controllable sizes has been achieved using different geometries of chromium pads immersed in various types of fluid. Effective blocking of microfluidic channels (cross-section 500 × 40 μm2) and direct pumping of fluid at a flow rate of 7.2–28.8 μl h−1with selectable direction have also been demonstrated. A particular advantage of this technique is that it allows the generation of bubbles at almost any location in the microchannel and thus enables microfluidic control at any point of interest. It can be readily integrated into lab-on-a-chip systems to improve functionality. [ABSTRACT FROM AUTHOR]

A novel active valving technique, whereby paraffin wax plugs in microchannels on a centrifugal microfluidic platform are actuated using focused infrared (IR) radiation is demonstrated in this report. Microchannels were simultaneously or sequentially opened using a stationary IR source by forming wax plugs with similar or differing melting points. The presented wax plugs offer key advantages over current active valving techniques, including a less involved fabrication procedure, a simpler actuation process, and the ability to multiplex experiment with active valves. In addition, a new technique for automated liquid reagent storage and release on the microfluidic disc platform, based on the formation and removal of a wax layer, is demonstrated. Overall, the techniques presented in this report offer novel methods for liquid handling, separation, and storage on the centrifugal microfluidic disc platform. [ABSTRACT FROM AUTHOR]

Chitosan is a naturally derived polymer with applications in a variety of industrial and biomedical fields. Recently, it has emerged as a promising material for biological functionalization of microelectromechanical systems (bioMEMS). Due to its unique chemical properties and film forming ability, chitosan serves as a matrix for the assembly of biomolecules, cells, nanoparticles, and other substances. The addition of these components to bioMEMS devices enables them to perform functions such as specific biorecognition, enzymatic catalysis, and controlled drug release. The chitosan film can be integrated in the device by several methods compatible with standard microfabrication technology, including solution casting, spin casting, electrodeposition, and nanoimprinting. This article surveys the usage of chitosan in bioMEMS to date. We discuss the common methods for fabrication, modification, and characterization of chitosan films, and we review a number of demonstrated chitosan-based microdevices. We also highlight the advantages of chitosan over some other functionalization materials for micro-scale devices. [ABSTRACT FROM AUTHOR]

We describe a control system to automatically distribute antibody-functionalized beads to addressable assay chambers within a PDMS microfluidic device. The system used real-time image acquisition and processing to manage the valve states required to sort beads with unit precision. The image processing component of the control system correctly counted the number of beads in 99.81% of images (2689 of 2694), with only four instances of an incorrect number of beads being sorted to an assay chamber, and one instance of inaccurately counted beads being improperly delivered to waste. Post-experimental refinement of the counting script resulted in one counting error in 2694 images of beads (99.96% accuracy). We analyzed a range of operational variables (flow pressure, bead concentration, etc.) using a statistical model to characterize those that yielded optimal sorting speed and efficiency. The integrated device was able to capture, count, and deliver beads at a rate of approximately four per minute so that bead arrays could be assembled in 32 individually addressable assay chambers for eight analytical measurements in duplicate (512 beads total) within 2.5 hours. This functionality demonstrates the successful integration of a robust control system with precision bead handling that is the enabling technology for future development of a highly multiplexed bead-based analytical device. [ABSTRACT FROM AUTHOR]

We present elements of electrolyte dynamics and electrochemistry relevant to microfluidic electrokinetics experiments. In Part I of this two-paper series, we presented a review and introduction to the fundamentals of acid–base chemistry. Here, we first summarize the coupling between acid–base equilibrium chemistry and electrophoretic mobilities of electrolytes, at both infinite and finite dilution. We then discuss the effects of electrode reactions on microfluidic electrokinetic experiments and derive a model for pH changes in microchip reservoirs during typical direct-current electrokinetic experiments. We present a model for the potential drop in typical microchip electrophoresis device. The latter includes finite element simulation to estimate the relative effects of channel and reservoir dimensions. Finally, we summarize effects of electrode and electrolyte characteristics on potential drop in microfluidic devices. As a whole, the discussions highlight the importance of the coupling between electromigration and electrophoresis, acid–base equilibria, and electrochemical reactions. [ABSTRACT FROM AUTHOR]

We describe a highly efficient microfluidic fluorescence-activated droplet sorter (FADS) combining many of the advantages of microtitre-plate screening and traditional fluorescence-activated cell sorting (FACS). Single cells are compartmentalized in emulsion droplets, which can be sorted using dielectrophoresis in a fluorescence-activated manner (as in FACS) at rates up to 2000 droplets s−1. To validate the system, mixtures of E. colicells, expressing either the reporter enzyme β-galactosidase or an inactive variant, were compartmentalized with a fluorogenic substrate and sorted at rates of ∼300 droplets s−1. The false positive error rate of the sorter at this throughput was <1 in 104droplets. Analysis of the sorted cells revealed that the primary limit to enrichment was the co-encapsulation of E. colicells, not sorting errors: a theoretical model based on the Poisson distribution accurately predicted the observed enrichment values using the starting cell density (cells per droplet) and the ratio of active to inactive cells. When the cells were encapsulated at low density (∼1 cell for every 50 droplets), sorting was very efficient and all of the recovered cells were the active strain. In addition, single active droplets were sorted and cells were successfully recovered. [ABSTRACT FROM AUTHOR]

RNA and DNA aptamers that bind to target molecules with high specificity and affinity have been a focus of diagnostics and therapeutic research. These aptamers are obtained by SELEX (Systematic Evolution of Ligands by EXponential enrichment) often requiring more than 10 successive cycles of selection and amplification, where each cycle normally takes 2 days per cycle of SELEX. Here, we have demonstrated the use of sol-gel arrays of proteins in a microfluidic system for efficient selection of RNA aptamers against multiple target molecules. The microfluidic chip incorporates five sol-gel binding droplets, within which specific target proteins are imbedded. The droplets are patterned on top of individually addressable electrical microheaters used for selective elution of aptamers bound to target proteins in the sol-gel droplets. We demonstrate that specific aptamers bind their respective protein targets and can be selectively eluted by micro-heating. Finally, our microfluidic SELEX system greatly improved selection efficiency, reducing the number of selection cycles needed to produce high affinity aptamers. The process is readily scalable to larger arrays of sol-gel-embedded proteins. To our knowledge, this is the first demonstration of a chip-based selection of aptamers using microfluidics, thereby allowing development of a high throughput and efficient SELEX procedures. [ABSTRACT FROM AUTHOR]

With the major advances in soft lithography and polymer materials, use of microfluidic devices has attracted tremendous attention recently. A simple and fast micromachining process is highly in demand to prototype such a device efficiently and economically. In this paper, we first reported an out-of-cleanroom printing-based integrated microfabrication process, referred to as the lab-on-a-print(LOP), for rapid-prototyping three-dimensional microfluidics. Using this lab-on-a-printprocess, we demonstrated the potential to accomplish an entire design-to-fabrication cycle within an hour, including about 70 µm resolution of direct-lithography patterning, well-controlled polyimide wet etching, three-dimensional pattern alignment and multilayer wax thermal-fusion packaging. A microfluidic gradient generator was prepared and tested for validation of the lab-on-a-printmicrofabrication process. [ABSTRACT FROM AUTHOR]

A new method for catalyst deposition on the inner walls of capillary microreactors is proposed which allows exact control of the coating thickness, pore size of the support, metal particle size, and metal loading. The wall-coated microreactors have been tested in a selective hydrogenation reaction. Activity and selectivity reach values close to those obtained with a homogeneous Pd catalyst. The catalyst activity was stable for a period of 1000 h time-on-stream. [ABSTRACT FROM AUTHOR]

We have successfully designed and fabricated an integrated microfluidic platform, the hESC-µChip, which is capable of reproducible and quantitative culture and analysis of individual hESC colonies in a semi-automated fashion. In this device, a serpentine microchannel allows pre-screening of dissociated hESC clusters, and six individually addressable cell culture chambers enable parallel hESC culture, as well as multiparameter analyses in sequence. In order to quantitatively monitor hESC proliferation and pluripotency status in real time, knock-in hESC lines with EGFP driven by the endogenous OCT4promoter were constructed. On-chip immunoassays of several pluripotency markers were carried out to confirm that the hESC colonies maintained their pluripotency. For the first time, our studies demonstrated well characterized hESC culture and analysis in a microfluidic setting, as well as a proof-of-concept demonstration of parallel/multiparameter/real-time/automated examination of self-renewal and differentiation in the same device. [ABSTRACT FROM AUTHOR]

We present a novel active mixing method in a microfluidic chip, where the controlled stirring of magnetic particles is used to achieve an effective mixing of fluids. To perform mixing, the ferromagnetic particles were embedded and manipulated under the influence of a rotating magnetic field. By aligning the magnetic beads along the magnetic field lines, rod-like structures are formed, functioning as small stir bars. Under higher flow conditions the particles did not form the typical rod structure but rather formed aggregates, which were even more beneficial for mixing. Our system reached a 96% mixing efficiency in a relatively short distance (800 µm) at a flow rate of 1.2–4.8 mm/s. These results demonstrate that our mixing method is useful for microfluidic devices with low aspect ratios and molecules with large molecular weights. [ABSTRACT FROM AUTHOR]

In this paper, signal amplifications of surface-enhanced Raman scattering (SERS) are realized by an optofluidic compact disc (CD)-based preconcentration method for effective label-free environmental and biomolecular detections. The preconcentration of target molecules is accomplished through the accumulation of adsorbed molecules on SERS-active sites by repeating a ‘filling–drying’ cycle of the assay solution in the optofluidic CD platform. After 30 cycles, the clear and high SERS signal of rhodamine 6G of 1 nM is readily detected. In addition to the preconcentration-based signal amplification by the optofluidic SERS system on the CD platform, we introduce a controlled precipitation of gold nanoparticles by CuSO4for SERS substrates. This method provides high-throughput, high-sensitive and large-area uniform SERS substrates on the optofluidic CD platform. The uniform SERS signals from different positions in spots of 3 mm2on the different CDs gives us confidence in the reliability and stability of our SERS substrates. [ABSTRACT FROM AUTHOR]

We present a simple microfluidic device that uses an array of well-defined chambers to immobilize thousands of femtoliter- to picoliter-scale aqueous drops suspended in inert carrier oil. This device enables timelapse studies of large numbers of individual drops, while simultaneously enabling subsequent drop recovery. [ABSTRACT FROM AUTHOR]

The soft lithographic technique is a collection of simple and cost-effective patterning techniques which applies an elastomeric stamp to transfer a nano/micro-scale pattern. Patterning biological materials using soft lithography provides procedurally simple control of the surface chemistry and the cell environments. However, conventional methods for generating microstructures on a substrate require expensive clean room facilities and skillful training. Here we report a simple and inexpensive clean-room free process using a conventional photomask film as a master to fabricate elastomeric stamps or microfluidic channels. This ultra rapid prototyping technique was applied to print FITC labeled poly-L-lysine with a 10 µm feature size on a glass substrate using soft lithographic processes, such as micro-contact printing and micromolding in capillaries, for patterning human hepatocellular carcinoma cells, human skin fibroblasts and hippocampal neurons from E-18 Sprague-Dawley rat. This novel technique using a photomask film as a master would be very useful ‘hands-on’ tool for the generation of micro-patterned chemical or biological assays using cells and proteins. [ABSTRACT FROM AUTHOR]

Despite the prevalence of microfluidic-based heterogeneous immunoassays (where analytes in solution are captured on a solid surface functionalized with a capture molecule), there is incomplete understanding of how assay parameters influence the amount of captured analytes. This study presents computational results and corresponding experimental binding assays in which the capture of analytes is studied under variations in both mass transfer and surface binding, constrained by real-world assay conditions of finite sample volume, assay time, and capture area. Our results identify: 1) a “reagent-limited” regime which exists only under the constraints of finite sample volume and assay time; 2) a critical flow rate (e.g.0.5 µL min−1under our assay conditions) to gain the maximum signal with the fastest assay time; 3) an increase in signal by using a short concentrated plug (e.g.5 µL, 100 nM) rather than a long dilute plug (e.g.50 µL, 10 nM) of sample; 4) the possibility of spending a considerable fraction of the assay time out of the reaction-limited regime. Overall, an improved understanding of fundamental physical processes may be particularly beneficial for the design of point-of-care assays, where volumes of reagents and available samples are limited, and the desired time-to-result short. [ABSTRACT FROM AUTHOR]

Elastomers based on poly(dimethylsiloxane) (PDMS) are promising materials for fabrication of a wide range of microanalytical systems due to their mechanical and optical properties and ease of processing. To date, however, quantitative studies that demonstrate reliable and reproducible methods for attachment of binding groups that capture complex receptor proteins of relevance to biomedical applications of PDMS microsystems have not been reported. Herein we describe methods that lead to the reproducible capture of a transmembrane protein, the human epidermal growth factor (EGF) receptor, onto PDMS surfaces presenting covalently immobilized antibodies for EGF receptor, and subsequent isolation of the captured receptor by mechanical transfer of the receptor onto a chemically functionalized surface of a gold film for detection. This result is particularly significant because the physical properties of transmembrane proteins make this class of proteins a difficult one to analyze. We benchmark the performance of antibodies to the human EGF receptor covalently immobilized on PDMS against the performance of the same antibodies physisorbed to conventional surfaces utilized in ELISA assays through the use of EGF receptor that was 32P-radiolabeled in its autophosphorylation domain. These results reveal that two pan-reactive antibodies for the EGF receptor (clones H11 and 111.6) and one phosphospecific EGF receptor antibody (clone pY1068) capture the receptor on both PDMS and ELISA plates. When using H11 antibody to capture EGF receptor and subsequent treatment with a stripping buffer (NaOH and sodium dodecylsulfate) to isolate the receptor, the signal-to-background obtained using the PDMS surface was 82 : 1, exceeding the signal-to-background measured on the ELISA plate (<48 : 1). We also characterized the isolation of captured EGF receptor by mechanical contact of the PDMS surface with a chemically functionalized gold film. The efficiency of mechanical transfer of the transmembrane protein from the PDMS surface was found to be 75–81%. However, the transfer of non-specifically bound protein was substantially less than 75%, thus leading to the important finding that mechanical transfer of the EGF receptor leads to an approximately four-fold increase in signal-to-background from 20 : 1 to 88 : 1. The signal-to-background obtained following mechanical transfer is also better than that obtained using ELISA plates and stripping buffer (<48 : 1). The EGF receptor is a clinically important protein and the target of numerous anticancer agents and thus these results, when combined, provide guidance for the design of PDMS-based microanalytical systems for the capture and isolation of complex and clinically important transmembrane proteins. [ABSTRACT FROM AUTHOR]

The use of microfluidic devices has become increasingly popular in the study of chemotaxis due to the exceptional control of flow properties and concentration profiles on the length scale of individual cells. In these applications, it is often neglected that cells, attached to the inner surfaces of the microfluidic chamber, are three-dimensional objects that perturb and distort the flow field in their vicinity. Depending on the interplay of flow speed and geometry with the diffusive time scale of the chemoattractant in the flow, the concentration distribution across the cell membrane may differ strongly from the optimal gradient in a perfectly smooth channel. We analyze the underlying physics in a two-dimensional approximation and perform systematic numerical finite element simulations to characterize the three-dimensional case and to identify optimal flow conditions. [ABSTRACT FROM AUTHOR]

In this paper, we report a new method of fabricating a high-throughput protein preconcentrator in poly(dimethylsiloxane) (PDMS) microfluidic chip format. We print a submicron thick ion-selective membrane on the glass substrate by using standard patterning techniques. By simply plasma-bonding a PDMS microfluidic device on top of the printed glass substrate, we can integrate the ion-selective membrane into the device and rapidly prototype a PDMS preconcentrator without complicated microfabrication and cumbersome integration processes. The PDMS preconcentrator shows a concentration factor as high as ∼104 in 5 min. This printing method even allows fabricating a parallel array of preconcentrators to increase the concentrated sample volume, which can facilitate an integration of our microfluidic preconcentrator chip as a signal enhancing tool to various detectors such as a mass spectrometer. [ABSTRACT FROM AUTHOR]

Holographic lithography in combination with photo-lithography provides a novel optofluidic platform through incorporation of periodic photonic units inside the microfluidic chips in a highly compatible and facile way. [ABSTRACT FROM AUTHOR]

Neuronal growth cones contain sophisticated molecular machinery precisely regulating their migration in response to complex combinatorial gradients of diverse external cues. The details of this regulation are still largely unknown, in part due to limitations of the currently available experimental techniques. Microfluidic devices have been shown to be capable of generating complex, stable and precisely controlled chemical gradients, but their use in studying growth cone migration has been limited in part due to the effects of shear stress. Here we describe a microfluidics-based turning-assay chip designed to overcome this issue. In addition to generating precise gradients of soluble guidance cues, the chip can also fabricate complex composite gradients of diffusible and surface-bound guidance cues that mimic the conditions the growth cones realistically counter in vivo. Applying this assay to Xenopus embryonic spinal neurons, we demonstrate that the presence of a surface-bound laminin gradient can finely tune the polarity of growth cone responses (repulsion or attraction) to gradients of brain-derived neurotrophic factor (BDNF), with the guidance outcome dependent on the mean BDNF concentration. The flexibility inherent in this assay holds significant potential for refinement of our understanding of nervous system development and regeneration, and can be extended to elucidate other cellular processes involving chemotaxis of shear sensitive cells. [ABSTRACT FROM AUTHOR]

We present a particle-sorting device based on the opposition of dielectrophoretic forces. The forces are generated by an array of electrode chambers located in both sidewalls of a main flow channel. Particles with different dielectric response perceive different force magnitudes and are therefore continuously focused to different streamlines in the flow channel. We relate the particles' dielectric response to their output position in the downstream channel. We demonstrate the performance of the device by separating a mixed yeast cell population into pure fractions of viable and nonviable cells. Finally, we use the device to enrich red blood cells infected with Babesia bovis, a major pathogen in cattle and simultaneously confirm the hypothesis that infection with B. bovis causes significant changes in the dielectric response of red blood cells. [ABSTRACT FROM AUTHOR]

There is great interest in genetic modification of bone marrow-derived mesenchymal stem cells (MSC), not only for research purposes but also for use in (autologous) patient-derived-patient-used transplantations. A major drawback of bulk methods for genetic modifications of (stem) cells, like bulk-electroporation, is its limited yield of DNA transfection (typically then 10%). This is even more limited when cells are present at very low numbers, as is the case for stem cells. Here we present an alternative technology to transfect cells with high efficiency (>75%), based on single cell electroporation in a microfluidic device. In a first experiment we show that we can successfully transport propidium iodide (PI) into single mouse myoblastic C2C12 cells. Subsequently, we show the use of this microfluidic device to perform successful electroporation of single mouse myoblastic C2C12 cells and single human MSC with vector DNA encoding a green fluorescent-erk1 fusion protein (EGFP-ERK1 (MAPK3)). Finally, we performed electroporation in combination with live imaging of protein expression and dynamics in response to extracellular stimuli, by fibroblast growth factor (FGF-2). We observed nuclear translocation of EGFP-ERK1 in both cell types within 15 min after FGF-2 stimulation. Due to the successful and promising results, we predict that microfluidic devices can be used for highly efficient small-scale ‘genetic modification’ of cells, and biological experimentation, offering possibilities to study cellular processes at the single cell level. Future applications might be small-scale production of cells for therapeutic application under controlled conditions. [ABSTRACT FROM AUTHOR]

We experimentally and theoretically demonstrate the proof-of-principle of a new lens-free cell monitoring platform that involves using an opto-electronic sensor array to record the shadow image of cells onto the sensor plane. This technology can monitor/count cells over a field-of-view that is more than two orders of magnitude larger than that of a conventional light microscope. Furthermore, it does not require any mechanical scanning or optical elements, such as microscope objectives or lenses. We also show that this optical approach can conveniently be combined with microfluidic channels, enabling parallel on-chip monitoring of various different cell types, e.g., blood cells, NIH-3T3 fibroblasts, murine embryonic stem cells, AML-12 hepatocytes. An important application of this approach could be a miniaturized point-of-care technology to obtain CD4 T lymphocyte counts of HIV infected patients in resource limited settings. [ABSTRACT FROM AUTHOR]

We demonstrate the fabrication and characterization of a novel, inexpensive microchip capable of laser induced fluorescence (LIF) detection using integrated waveguides with built-in optical filters. Integrated wavelength-selective optical waveguides are fabricated by doping poly(dimethysiloxane) (PDMS) with dye molecules. Liquid-core waveguides are created within dye-doped PDMS microfluidic chips by filling channels with high refractive index liquids. Dye molecules are allowed to diffuse into the liquid core from the surrounding dye-doped PDMS. The amount of diffusion is controlled by choosing either polar (low diffusion) or apolar (high diffusion) liquid waveguide cores. The doping dye is chosen to absorb excitation light and to transmit fluorescence emitted by the sample under test. After 24 h, apolar waveguides demonstrate propagation losses of 120 dB cm–1 (532 nm) and 4.4 dB cm–1 (633 nm) while polar waveguides experience losses of 8.2 dB cm–1 (532 nm) and 1.1 dB cm–1 (633 nm) where 532 and 633 nm light represent the excitation and fluorescence wavelengths, respectively. We demonstrate the separation and detection of end-labelled DNA fragments using polar waveguides for excitation light delivery and apolar waveguides for fluorescence collection. We demonstrate that the dye-doped waveguides can provide performance comparable to a commercial dielectric filter; however, for the present choice of dye, their ultimate performance is limited by autofluorescence from the dye. Through the detection of a BK virus polymerase chain reaction (PCR) product, we demonstrate that the dye-doped PDMS system is an order of magnitude more sensitive than a similar undoped system (SNR: 138 vs. 9) without the use of any external optical filters at the detector. [ABSTRACT FROM AUTHOR]

Retroviruses are one of the most commonly used vectors in ongoing gene therapy clinical trials. To evaluate and advance virus production on the microscale platform, we have created a novel microfluidic bioreactor for continuous retrovirus production. We investigated the growth kinetics of a retroviral packaging cell line in microfluidic bioreactors for several compartment sizes, and packaging cells perfused in the microdevices showed similar growth kinetics to those cultured in conventional static conditions. To evaluate the efficiency of retrovirus production, virus titers from the microdevices were compared to those obtained from static tissue culture. When retrovirus production and collection were maintained at 37 °C, virus production levels were comparable for the microdevices and static tissue culture conditions. However, immediate cold storage downstream of the packaging cells in the microdevices resulted in 1.4- to 3.7-fold greater active virus production levels with the microdevices compared to the conventional static conditions over a 5 day period. Lastly, the use of microfluidics for virus production provides a continuous supply of virus supernatant for immediate infection of target cells or for preservation and storage. Such devices will be valuable for the optimization of production and evaluation of retroviruses and other viral vectors for gene therapy applications. [ABSTRACT FROM AUTHOR]

Microfluidic devices that reduce evaporative loss during thermal bioreactions such as PCR without microvalves have been developed by relying on the principle of diffusion-limited evaporation. Both theoretical and experimental results demonstrate that the sample evaporative loss can be reduced by more than 20 times using long narrow diffusion channels on both sides of the reaction region. In order to further suppress the evaporation, the driving force for liquid evaporation is reduced by two additional techniques: decreasing the interfacial temperature using thermal isolation and reducing the vapor concentration gradient by replenishing water vapor in the diffusion channels. Both thermal isolation and vapor replenishment techniques can limit the sample evaporative loss to approximately 1% of the reaction content. [ABSTRACT FROM AUTHOR]

Microfluidic devices are well suited for manipulating and measuring mass limited samples. Here we adapt a microfluidic device containing functionalized surfaces to chemically stimulate a small number of neurons (down to a single neuron), collect the release of neuropeptides, and characterize them using mass spectrometry. As only a small fraction of the peptides present in a neuron are released with physiologically relevant stimulations, the amount of material available for measurement is small, thereby requiring minimal sample loss and high-sensitivity detection. Although a number of detection schemes are used with microfluidic devices, mass spectrometric detection is used here because of its high information content, allowing the characterization of the released peptide complement. Rather than using an on-line approach, off-line analysis is used; after collection of the peptides onto a surface, mass spectrometric imaging interrogates that surface to determine the peptides released from the cell. The overall utility of this scheme is demonstrated using several device formats with measurement of neuropeptides released from Aplysia californica bag cell neurons. [ABSTRACT FROM AUTHOR]

Achieving efficient passivation of micro-channels against non-specific adsorption of biomolecules is a critical aspect in the development of microfluidic ELISA systems. Usual surface treatments such as pre-coating of the channels with serum albumin, exposure to oxygen plasma, polyethylene glycol grafting however exhibit a lack of long-term stability, with procedures that can be time-consuming, complex or associated with costly materials and instruments. In this paper, we present a new fluidic design combined with an original strategy of manipulating magnetic beads in order to reduce assay noise in bead-based microfluidic ELISA without the need for prior channel pre-treatment. The novelty of the system relies on the physical separation of the immune complex formation phase and the enzymatic reaction phase into two independent networks of channels. These networks are linked by fluidic bridges, whose openings are controlled by pressure valves, and through which the beads are magnetically transferred. A standard curve for the quantification of a model antibody was obtained within 30 minutes. A detection limit of 100 pg mL−1 (660 fM) and good linearity of the signal up to 4 ng mL−1 were observed. [ABSTRACT FROM AUTHOR]

The fabrication and performance of a microfluidic device with integrated liquid-core optical waveguides for laser induced fluorescence DNA fragment analysis is presented. The device was fabricated through poly(dimethylsiloxane) (PDMS) soft lithography and waveguides are formed in dedicated channels through the addition of a liquid PDMS pre-polymer of higher refractive index. Once a master has been fabricated, microfluidic chips can be produced in less than 3 h without the requirement for a cleanroom, yet this method provides an optical system that has higher performance than a conventional confocal optical assembly. Optical coupling was achieved through the insertion of optical fibers into fiber-to-waveguide couplers at the edge of the chip and the liquid–fiber interface results in low reflection and scattering losses. Waveguide propagation losses are measured to be 1.8 dB cm−1 (532 nm) and 1.0 dB cm−1 (633 nm). The chip displays an average total coupling loss of 7.6 dB due to losses at the optical fiber interfaces. In the electrophoretic separation and detection of a BK virus PCR product, the waveguide system achieves an average signal-to-noise ratio of 570 ± 30 whereas a commercial confocal benchtop electrophoresis system achieves an average SNR of 330 ± 30. To our knowledge, this is the first time that a waveguide-based system has been demonstrated to have a SNR comparable to a commercially available confocal-based system for microchip capillary electrophoresis. [ABSTRACT FROM AUTHOR]

The esterification reaction of phthalic anhydride with methanol was performed at different temperatures in a continuous flow glass microreactor at pressures up to 110 bar and using supercritical CO2 as a co-solvent. The design is such that supercritical CO2 can be generated inside the microreactor. Substantial rate enhancements were obtained, viz. a 53-fold increase was obtained at 110 bar and 60 °C. Supercritical CO2 as a co-solvent gave rise to a 5400-fold increase (both with respect to batch experiments at 1 bar at the same temperature). [ABSTRACT FROM AUTHOR]

We present a novel technique to accurately position single cells on a substrate using negative dielectrophoresis and cell–substrate adhesion. The cells are suspended in physiological media throughout the patterning process. We also verify the biocompatibility of this method by demonstrating that the patterned cells proliferate and show normal morphology. We calculate the temperatures and transmembrane potential that cells in the device experience and compare them to physiologically acceptable levels described in previous studies. [ABSTRACT FROM AUTHOR]

Culturing cells at microscales allows control over microenvironmental cues, such as cell–cell and cell–matrix interactions; the potential to scale experiments; the use of small culture volumes; and the ability to integrate with microsystem technologies for on-chip experimentation. Microfluidic perfusion culture in particular allows controlled delivery and removal of soluble biochemical molecules in the extracellular microenvironment, and controlled application of mechanical forces exerted via fluid flow. There are many challenges to designing and operating a robust microfluidic perfusion culture system for routine culture of adherent mammalian cells. The current literature on microfluidic perfusion culture treats microfluidic design, device fabrication, cell culture, and micro-assays independently. Here we systematically present and discuss important design considerations in the context of the entire microfluidic perfusion culture system. These design considerations include the choice of materials, culture configurations, microfluidic network fabrication and micro-assays. We also present technical issues such as sterilization; seeding cells in both 2D and 3D configurations; and operating the system under optimized mass transport and shear stress conditions, free of air-bubbles. The integrative and systematic treatment of the microfluidic system design and fabrication, cell culture, and micro-assays provides novices with an effective starting point to build and operate a robust microfludic perfusion culture system for various applications. [ABSTRACT FROM AUTHOR]

Valving is critical in microfluidic systems. Among many innovative microvalves used in lab-on-a-chip applications, phase change based microvalves using paraffin wax are particularly attractive for disposable biochip applications because they are simple to implement, cost-effective and biocompatible. However, previously reported paraffin-based valves require embedded microheaters and therefore multi-step operation of many microvalves was a difficult problem. Besides, the operation time was relatively long, 2–10 s. In this paper, we report a unique phase change based microvalve for rapid and versatile operation of multiple microvalves using a single laser diode. The valve is made of nanocomposite materials in which 10 nm-sized iron oxide nanoparticles are dispersed in paraffin wax and used as nanoheaters when excited by laser irradiation. Laser light of relatively weak intensity was able to melt the paraffin wax with the embedded iron oxide nanoparticles, whereas even a very intense laser beam does not melt wax alone. The microvalves are leak-free up to 403.0 ± 7.6 kPa and the response times to operate both normally closed and normally opened microvalves are less than 0.5 s. Furthermore, a sequential operation of multiple microvalves on a centrifugal microfluidic device using a single laser diode was demonstrated. It showed that the optical control of multiple microvalves is fast, robust, simple to operate, and requires minimal chip space and thus is well suited for fully integrated lab-on-a-chip applications. [ABSTRACT FROM AUTHOR]

Using the concept of insulator-based “electrodeless” dielectrophoresis, we present a novel geometry for shaping electric fields to achieve lateral deviation of particles in liquid flows. The field is generated by lateral planar metal electrodes and is guided along access channels to the active area in the main channel. The equipotential surfaces at the apertures of the access channels behave as vertical “liquid” electrodes injecting the current into the main channel. The field between a pair of adjacent liquid electrodes generates the lateral dielectrophoretic force necessary for particle manipulation. We use this force for high-speed deviation of particles. By adding a second pair of liquid electrodes, we focus a particle stream. The position of the focused stream can be swept across the channel by adjusting the ratio of the voltages applied to the two pairs. Based on conformal mapping, we provide an analytical model for estimating the potential at the liquid electrodes and the field distribution in the main channel. We show that the simulated particle trajectories agree with observations. Finally, we show that the model can be used to optimize the device geometry in different applications. [ABSTRACT FROM AUTHOR]