Search

This research work articulates the microstructural features of the dissimilar weldments involving Ni based superalloy Inconel 718 and martensitic stainless steel, AISI 416 that is difficult to weld. Autogenous tungsten inert gas (TIG) welding was carried out with and without using flux to fabricate these bimetallic combinations. Microstructure at the fusion zones and the interfaces were characterized using optical and scanning electron microscopy. The results depicted the presence of fine martensite at the heat affected zone (HAZ) of AISI 416 and the formation of unmixed zone containing secondary phases at the HAZ of Inconel 718. Similarly, the formation of Nb rich eutectics along with sulfides was witnessed at the fusion zone of both the weldments. Owing to the low heat input witnessed during the flux assisted TIG welding, the Nb segregation was found to be minimal. Tensile studies reported that the fracture occurred at the fusion zone in both the cases. It was inferred from the tensile studies that the joint strength of the weldments with flux addition was greater than the ones without flux. This study demonstrated that dissimilar joints with complete penetration could be achieved in single pass using the TIG welding process with the aid of flux. [ABSTRACT FROM AUTHOR]

The metallurgical and mechanical properties of electron beam welded Ni based superalloy Inconel 625 and UNS S32205 duplex stainless steel plates have been investigated in the present study. Interface microstructure studies divulged the absence of any grain coarsening effects or the formation of any secondary phases at the heat affected zone (HAZ) of the electron beam (EB) weldments. Tensile studies showed that the fracture occurred at the weld zone in all the trials and the average weld strength was reported to be 850 MPa. Segregation of Mo rich phases was witnessed at the inter-dendritic arms of the fusion zone. The study recommended the use of EB welding for joining these dissimilar metals by providing detailed structure – property relationships. [ABSTRACT FROM AUTHOR]

In the present investigation, an attempt has been made to weld the precipitation hardened Nickel based super alloy Inconel 718 and austenitic stainless steel AISI 316L using Continuous Current Gas Tungsten Arc Welding (CCGTAW) and Pulsed Current Gas Tungsten Arc Welding (PCGTAW) process employing ER2553 and ERNiCu-7 fillers. Microstructure examination using optical and SEM analysis clearly witnessed the formation of unmixed zone at the Heat Affected Zone (HAZ) of Inconel 718 for all the joints. The studies showed the absence of deleterious phases in the CCGTA and PCGTA weldments employing ERNiCu-7. Tensile studies corroborated that the fracture occurred at the parent metal of AISI 316L in all the cases. It was inferred from the present study that PCGTA weldments employing ERNiCu-7 exhibited better metallurgical and mechanical properties. This study articulated the effect of filler metals on the structure-property relationships of the weldments. [ABSTRACT FROM AUTHOR]

Highlights: [•] Effect of filler metals on the weldability of super-duplex stainless steel plates. [•] Contemplative explanations on the metallurgical and mechanical properties of the weldments. [•] Enhanced mechanical properties of the welds at ambient room temperature. [ABSTRACT FROM AUTHOR]

Abstract: Dissimilar metal welding involving AISI 304 and Monel 400 finds widespread use in marine and offshore environments for the fabrication of heat exchangers, evaporators, piping and vessels in petrochemical and power generation industries. However studies on the performance of such weldments are scantly found in the literature even though the individual metals have higher corrosion resistance and strength. This paper reports the work carried out on welding of AISI 304 and Monel 400 using Gas Tungsten Arc Welding (GTAW) technique to examine the weldability, mechanical and metallurgical properties. Investigations have been carried out on the hot corrosion behavior of these joints subjected to cyclic air oxidation and K2SO4 +NaCl (60%) molten salt environment at 600°C. A comparative analysis was carried out on these weldments for two different filler metals such as E309L and ENiCu-7. The oxide scales formed on the various zones of the weldment have been characterized systematically using surface analytical techniques. Weld zone was found to be more susceptible to degradation than base metals used. The effect of filler materials on the hot corrosion is discussed. The studies reported in this paper would be beneficial for fabricators embracing this type of dissimilar weldments in the petrochemical and power generation industries. [Copyright &y& Elsevier]

Abstract: In this paper, vibration and damping of composite sandwich box column containing viscoelastic layer (VEL) or electrorheological fluid (ER) core with constraining layer and their performance comparison is carried out. The finite element based modal strain energy method is used for predicting the modal loss factor and frequency of laminated composite box columns with integral viscoelastic/ER fluid layers. Effects of core thickness, orientation of the fiber in the base plate and constraining layer, applied voltage and stacking sequence on the vibration behavior of composite sandwich box column for clamped-free boundary condition are studied in the paper. The performance comparison of vicsoelastic layer damping and ER layer damping is also investigated. [Copyright &y& Elsevier]