Search

Interest towards cellulose nanofibers obtained from virgin and waste sources has seen a significant growth, mainly thanks to the increasing sensitivity towards the concept of circular economy and the high levels of paper recycling achieved in recent years. Inspired by the guidelines of the green building industry, this study proposes the production and characterization of TEMPO-oxidized and homogenized cellulose nanofibers (TOHO CNF) from different sources and their use as additives for earth plasters on two different raw earth samples, characterized by geotechnical laboratory tests and mineralogical analysis: a high-plasticity clay (T2) and a medium-compressibility silt (ABS). Original sources, including those derived from waste (recycled cardboard and paper mill sludge), were characterized by determining chemical content (cellulose versus ashes and lignin) and fiber morphology. TOHO CNF derived from the different sources were compared in terms of nanofibers medium diameter, crystallinity degree, thermal decomposition and oxidation degree, that is the content of carboxylic groups per gram of sample. Then, a preliminary analysis of the influence of CNF on earth plasters is examined. Adhesion and capillary absorption tests highlighted the effect of such nanofibers on blends in function of two factors, namely the cellulose original source and the oxidation degree of the fibers. In particular, for both earth samples, T2 and ABS, a significant increase in adhesion strength was observed in the presence of some TOHO CNF additives. As far as capillary sorption tests, while an undesired increase in water adsorption was detected for T2 compared to the control, in the case of ABS, a significant reduction in water content was measured by adding TOHO CNF derived from recycled sources. These results pave the way for further in-depth investigation on the role of TOHO CNF as additives for earth plasters. [ABSTRACT FROM AUTHOR]

Currently, the pulp and paper industry generates around 50–70 million tons of lignin annually, which is mainly burned for energy recovery. Lignin, being a natural aromatic polymer rich in functional hydroxyl groups, has been drawing the interest of academia and industry for its valorization, especially for the development of polymeric materials. Among the different types of polymers that can be derived from lignin, polyurethanes (PUs) are amid the most important ones, especially due to their wide range of applications. This review encompasses available technologies to isolate lignin from pulping processes, the main approaches to convert solid lignin into a liquid polyol to produce bio-based polyurethanes, the challenges involving its characterization, and the current technology assessment. Despite the fact that PUs derived from bio-based polyols, such as lignin, are important in contributing to the circular economy, the use of isocyanate is a major environmental hot spot. Therefore, the main strategies that have been used to replace isocyanates to produce non-isocyanate polyurethanes (NIPUs) derived from lignin are also discussed. [ABSTRACT FROM AUTHOR]

The integration of recycled polymers into additive manufacturing (AM) processes offers a promising opportunity for advancing sustainability within the manufacturing industry. This review paper summarizes existing research and developments related to the use of recycled materials in AM, focusing on distinct polymers, such as polylactic acid (PLA), polyethylene terephthalate (PET), and acrylonitrile butadiene styrene (ABS), among others. Key topics explored include the availability of recycled filaments on the market, challenges associated with material variability and traceability, and efforts toward establishing ethical product standards and sustainability characterization methodologies. Regulatory considerations and standards development by organizations such as ASTM and ISO are discussed, along with recommendations for future advancements in improving the sustainability of filament recycling and achieving net-zero emissions in AM processes. The collective efforts outlined in this paper underscore the potential of recycled polymers in AM to foster a more sustainable and environmentally friendly manufacturing industry. [ABSTRACT FROM AUTHOR]

In this review article, we focus on the relationship between permanent magnets and the electric motor, as this relationship has not been covered in a review paper before. With the increasing focus on battery research, other parts of the electric system have been neglected. To make electrification a smooth transition, as has been promised by governing bodies, we need to understand and improve the electric motor and its main component, the magnet. Today's review papers cover only the engineering perspective of the electric motor or the material-science perspective of the magnetic material, but not both together, which is a crucial part of understanding the needs of electric-motor design and the possibilities that a magnet can give them. We review the road that leads to today's state-of-the-art in electric motors and magnet design and give possible future roads to tackle the obstacles ahead and reach the goals of a fully electric transportation system. With new technologies now available, like additive manufacturing and artificial intelligence, electric motor designers have not yet exploited the possibilities the new freedom of design brings. New out-of-the-box designs will have to emerge to realize the full potential of the new technology. We also focus on the rare-earth crisis and how future price fluctuations can be avoided. Recycling plays a huge role in this, and developing a self-sustained circular economy will be critical, but the road to it is still very steep, as ongoing projects show. [ABSTRACT FROM AUTHOR]

Textile dyeing is known to have major environmental concerns, especially with the high use of toxic chemicals. The use of alternatives such as natural dyes rich in phenolic compounds has become extremely appealing in order to move towards a more sustainable circular economy. Phenolic dyes have the potential to functionalize textile fabrics with properties such as antimicrobial, antioxidant, and UV protection. Wastes/residues from the agri-food industries stand out as highly attractive sources of these compounds, with several by-products showing promising results in textile dyeing through the implementation of more sustainable and eco-friendly processes. This review presents an up-to-date exploration of the sources of phenolic compounds used in the textile industry over the past two decades, with a primary focus on the functional properties they provide to different fabrics. The research highlights a surge in interest in this theme since 2017, accentuating a noticeable upward trend. Throughout this review, emphasis is given to by-products from the agri-food industry as the sources of these compounds. The reviewed papers lay the foundation for future research, paving the way for exploring the potential of raw materials and by-products in the creation of functional and smart textiles. [ABSTRACT FROM AUTHOR]

In recent times, circular economy initiatives in addition to the need for sustainable biomaterials have brought about several attempts at the eco-friendly, eco-sustainable and cost-effective production of asphalt pavements. It is an increasingly common practice in the asphalt industry to improve road pavement performance using additives to enhance the physico-chemical properties of bitumen, which performs the role of the binder in the asphalt mix. This paper evaluated the potential of a bio-based additive derived from olive leaf residue as a modifier and antioxidant agent for bitumen. Samples of neat, aged and doped aged bitumen were analyzed. In this study, the two bio-based additives were characterized in terms of phenol, chlorophyll, lignin and cellulose content, which was correlated with the mechanical properties of the tested samples. The mechanical properties of the neat, modified, aged and unaged samples were evaluated via Dynamic Shear Rheology. The bio-based additives proved to be promising and can improve the properties of bitumen binder and the performance of asphalt pavements in general. [ABSTRACT FROM AUTHOR]

Plasmas are reactive ionised gases, which enable the creation of unique reaction fields. This allows plasmas to be widely used for a variety of chemical processes for materials, recycling among others. Because of the increase in urgency to find more sustainable methods of waste management, plasmas have been enthusiastically applied to recycling processes. This review presents recent developments of plasma technologies for recycling linked to economical models of circular economy and waste management hierarchies, exemplifying the thermal decomposition of organic components or substances, the recovery of inorganic materials like metals, the treatment of paper, wind turbine waste, and electronic waste. It is discovered that thermal plasmas are most applicable to thermal processes, whereas nonthermal plasmas are often applied in different contexts which utilise their chemical selectivity. Most applications of plasmas in recycling are successful, but there is room for advancements in applications. Additionally, further perspectives are discussed. [ABSTRACT FROM AUTHOR]

Over 50 MioT of Waste Cooking Oil (WCO) was collected worldwide in 2020 from domestic and industrial activities, constituting a potential hazard for both water and land environments, and requiring appropriate disposal management strategies. In line with the principles of circular economy and eco-design, in this paper an innovative methodology for the valorisation of WCO as a rejuvenating agent for bitumen 50/70 coming from Reclaimed Asphalt Pavement (RAP) is reported. In particular, WCO or hydrolysed WCO (HWCO) was modified by transesterification or amidation reactions to achieve various WCO esters and amides. All samples were characterised by nuclear magnetic resonance, melting, and boiling point. Since rejuvenating agents for RAP Cold Mix Asphalt require a melting point ≤0 °C, only WCO esters could further be tested. Efficiency of WCO esters was assessed by means of the Asphaltenes Dispersant Test and the Heithaus Parameter. In particular, bitumen blends containing 25 wt% of WCO modified with 2-phenylethyl alcohol, showed high dispersing capacity in n-heptane even after a week, compared to bitumen alone (1 h). Additionally, the Heithaus Parameter of this bitumen blend was almost three times higher than bitumen alone, further demonstrating beneficial effects deriving from the use of WCO esters as rejuvenating agents. [ABSTRACT FROM AUTHOR]

The intensive development of the polyurethanes industry and limited resources (also due to the current geopolitical situation) of the raw materials used so far force the search for new solutions to maintain high economic development. Implementing the principles of a circular economy is an approach aimed at reducing the consumption of natural resources in PU production. This is understood as a method of recovery, including recycling, in which waste is processed into PU, and then re-used and placed on the market in the form of finished sustainable products. The effective use of waste is one of the attributes of the modern economy. Around the world, new ways to process or use recycled materials for polyurethane production are investigated. That is why innovative research is so important, in which development may change the existing thinking about the form of waste recovery. The paper presents the possibilities of recycling waste (such as biochar, bagasse, waste lignin, residual algal cellulose, residual pineapple cellulose, walnut shells, silanized walnut shells, basalt waste, eggshells, chicken feathers, turkey feathers, fiber, fly ash, wood flour, buffing dust, thermoplastic elastomers, thermoplastic polyurethane, ground corncake, Tetra Pak®, coffee grounds, pine seed shells, yerba mate, the bark of Western Red Cedar, coconut husk ash, cuttlebone, glass fibers and mussel shell) as additives or fillers in the formulation of polyurethanes, which can partially or completely replace petrochemical raw materials. Numerous examples of waste applications of one-component polyurethanes have been given. A new unexplored niche for the research on waste recycling for the production of two components has been identified. [ABSTRACT FROM AUTHOR]

The purpose of this manuscript is to present a review of laboratory experiments (including methodology and results) that use biochar, a specific carbon obtained by a pyrolysis process from different feedstocks, as an alternative material for heavy metal adsorption from groundwater. In recent years, many studies have been conducted regarding the application of innovative materials to water decontamination to develop a more sustainable approach to remediation processes. The use of biochar for groundwater remediation has particularly attracted the interest of researchers because it permits the reuse of materials that would be otherwise disposed of, in accordance with circular economy, and reduces the generation of greenhouse gases if compared to the use of virgin materials. A review of the different approaches and results reported in the current literature could be useful because when applying remediation technologies at the field scale, a preliminary phase in which the suitability of the adsorbent is evaluated at the lab scale is often necessary. This paper is therefore organised with a short description of the involved metals and of the biochar production and composition. A comprehensive analysis of the current knowledge related to the use of biochar in groundwater remediation at the laboratory scale to obtain the characteristic parameters of the process that are necessary for the upscaling of the technology at the field scale is also presented. An overview of the results achieved using different experimental conditions, such as the chemical properties and dosage of biochar as well as heavy metal concentrations with their different values of pH, is reported. At the end, numerical studies useful for the interpretation of the experiment results are introduced. [ABSTRACT FROM AUTHOR]

The cement sector is the second largest contributor to anthropogenic CO2 emissions, and several efforts have been made to reduce its environmental impact. One alternative that has gained interest in recent years involves the use of municipal solid waste incineration (MSWI) bottom ash (BA) as clinker/cement replacement. This paper studies the application of MSWI BA in three different ways: (i) aggregate (0 to 100 v/v %), (ii) partial binder substitute (0 to 30 v/v %), and (iii) filler (5 v/v %). It stands out for its approach in characterizing seven distinct BA particle sizes and for the development and analysis of eco-cement mortars with only mechanically pre-treated BA. Hardened state properties showed that the use of BA as aggregate leads to deterioration and efflorescence formation on the surface of the mortars, making this application unfeasible. The replacement of 15 v/v % of OPC (Ordinary Portland Cement) by BA and the use of finer (<63 μm) BA as filler caused a decrease in the compressive strength of the mortar, from 15.8 to 9.3 and 11.0, respectively. However, these materials are suitable for use in walls where the minimum required mechanical resistance is 5 MPa. Furthermore, these mortars demonstrated resilience against freeze–thaw cycles and even exhibited increased compressive strength after 25 cycles. Thus, this work showed that MSWI BA can be used as an OPC substitute (up to 15 v/v %) and as a filler, promoting circular economy principles and reducing CO2 emissions related to the construction industry. [ABSTRACT FROM AUTHOR]

Recycled aggregate concrete (RAC) includes recycled concrete aggregates (coarse and/or fine) as substitutes for natural aggregates as an approach to achieving a circular economy. Some concerns remain about its performance, including the carbonation resistance. The higher porosity of recycled concrete aggregates is logically a disadvantage, but the analysis must address many other factors. This paper provides an in-depth examination of recent advances in the carbonation performance of RAC. The emphasis is on factors that influence CO2 diffusion and the carbonation rate, e.g., the replacement ratio, source concrete quality, interfacial transition zone features, residual portlandite content, and porosity. The influences of previous treatments, combined action with supplementary cementitious materials, and loading conditions are also discussed. The replacement ratio has a significant impact on the carbonation performance of concrete, but it is also dependent on other factors. During carbonation, the physical effects of the porosity of the aggregate and the physical–chemical effects of the portlandite content in the adhered mortar are particularly important. The residual portlandite is especially significant because it is the primary hydration product responsible for the alkaline reserve for carbonation and the potential pozzolanic reaction, which are per se competing factors that determine the carbonation rate. [ABSTRACT FROM AUTHOR]

Starting from the context of the principles of Sustainable Development and Circular Economy concepts, the paper presents a synthesis of research in the field of the development of materials of interest, such as cementitious composites or alkali-activated geopolymers. Based on the reviewed literature, the influence of compositional or technological factors on the physical-mechanical performance, self-healing capacity and biocidal capacity obtained was analyzed. The inclusion of TiO2 nanoparticles in the matrix increase the performances of cementitious composites, producing a self-cleaning capacity and an anti-microbial biocidal mechanism. As an alternative, the self-cleaning capacity can be achieved through geopolymerization, which provides a similar biocidal mechanism. The results of the research carried out indicate the real and growing interest for the development of these materials but also the existence of some elements still controversial or insufficiently analyzed, therefore concluding the need for further research in these areas. The scientific contribution of this study consists of bringing together two apparently distinct research directions in order to identify convergent points, to create a favorable framework for the development of an area of research little addressed so far, namely, the development of innovative building materials by combining improved performance with the possibility of reducing environmental impact, awareness and implementation of the concept of a Circular Economy. [ABSTRACT FROM AUTHOR]

In recent years, a dynamic increase in environmental pollution with textile waste has been observed. Natural textile waste has great potential for environmental applications. This work identifies potential ways of sustainably managing natural textile waste, which is problematic waste from sheep farming or the cultivation of fibrous plants. On the basis of textile waste, an innovative technology was developed to support water saving and plant vegetation- biodegradable water-absorbing geocomposites (BioWAGs). The major objective of this study was to determine BioWAG effectiveness under field conditions. The paper analyses the effect of BioWAGs on the increments in fresh and dry matter, the development of the root system, and the relative water content (RWC) of selected grass species. The conducted research confirmed the high efficiency of the developed technology. The BioWAGs increased the fresh mass of grass shoots by 230-420% and the root system by 130-200% compared with the control group. The study proved that BioWAGs are a highly effective technology that supports plant vegetation and saves water. Thanks to the reuse of waste materials, the developed technology is compatible with the assumptions of the circular economy and the goals of sustainable development. [ABSTRACT FROM AUTHOR]

Biochar has shown great promise in producing low-cost low-carbon concrete for civil infrastructure applications. However, there is limited research comparing the use of pristine and contaminated biochar in concrete. This paper presents comprehensive laboratory experiments and three-dimensional nonlinear finite element analysis on the mechanical, economical, and environmental performance of reinforced concrete beams made using concrete blended with biochar generated from vetiver grass roots after the roots were used in an oil extraction process. Both pristine biochar and biochar that were used to treat wastewater through adsorbing heavy metals (100 mg/L of Pb, Cu, Cd, and Zn) were investigated. The biochar was used to replace up to 6% Portland cement in concrete. Laboratory experiments were conducted to characterize the workability, mechanical properties, shrinkage, and leaching potential of the concrete blended with biochar. The results showed that using biochar could increase the compressive strengths and reduce the shrinkage of concrete without causing a leaching problem. The results from finite element analysis of the reinforced concrete beams showed that the use of biochar was able to increase the flexural performance of the beams as well as their economic and environmental performance. This research will promote the development and structural applications of low-cost low-carbon concrete. [ABSTRACT FROM AUTHOR]

The building and construction industry is a key sector behind the ecological transition in that it is one of the main responsible factors in the consumption of natural resources. Thus, in line with circular economy, the use of waste aggregates in mortars is a possible solution to increase the sustainability of cement materials. In the present paper, polyethylene terephthalate (PET) from bottle scraps (without chemical pretreatment) was used as aggregate in cement mortars to replace conventional sand aggregate (20%, 50% and 80% by weight). The fresh and hardened properties of the innovative mixtures proposed were evaluated through a multiscale physical-mechanical investigation. The main results of this study show the feasibility of the reuse of PET waste aggregates as substitutes for natural aggregates in mortars. The mixtures with bare PET resulted in less fluid than the specimens with sand; this was ascribed to the higher volume of the recycled aggregates with respect to sand. Moreover, PET mortars showed a high tensile strength and energy absorption capacity (with Rf = 1.9 ÷ 3.3 MPa, Rc = 6 ÷ 13 MPa); instead, sand samples were characterized by a brittle rupture. The lightweight specimens showed a thermal insulation increase ranging 65–84% with respect to the reference; the best results were obtained with 800 g of PET aggregate, characterized by a decrease in conductivity of approximately 86% concerning the control. The properties of these environmentally sustainable composite materials may be suitable for non-structural insulating artifacts. [ABSTRACT FROM AUTHOR]

The paper presents the results of research on a composite mixture intended for use in road construction. The purpose of developing the mixture is to be able to use large amounts of industrial waste to produce building material. The waste used are coal slate from the mining industry, shredded rubber waste from used passenger car tires and fly ash from power plants. The mixture (SRFC) consists of unburnt coal-mining slate (S), shredded rubber waste (R), fly ash (F) and cement(C). A test under cyclic loading conditions was carried out on samples prepared from the SRFC mixture, in which the global deformations and local strains caused on the samples were measured. A measurement system using digital image correlation was used for the research. On the basis of the conducted research, it was found that the content of shredded rubber waste significantly influences the deformability of the tested mixtures and allows for the extension of the scope of elastic deformation in which the tested samples work. [ABSTRACT FROM AUTHOR]

The objective of this paper is to provide a comprehensive study about the performance of concrete using mixed coarse recycled aggregate (MCRA) as an alternative for natural aggregate (NA) at replacement levels of 0, 30, 60, and 100%, which can greatly reduce the environmental pollution by incorporating the construction and demolition wastes in the reproduction of concrete. The focus of this study was to use the raw MCRA that was directly obtained from a recycling plant and not further processed. Initially, MCRA was studied to ascertain if its property meets the recommended Indian standards for natural aggregates. Using the slump test, the workability of freshly prepared concrete with a characteristic strength of 30 MPa was assessed. Additionally, the mechanical performance of concrete was assessed on the specimens prepared in the different forms: cubes, cylinders, and beams. Moreover, Scanning Electron Microscopy (SEM) with EDAX, XRD, and FTIR were used to study the microstructural behavior of selected optimum and control mixes at 7 and 28 days of curing. The studies revealed that a higher MCRA content improved the workability of concrete and 30% replacement of MCRA improved the compressive strength by 11.01, 6.98, 6.19, and 14.24% at 7, 28, 56, and 90 days respectively. At the same time, the 30% replacement of the MCRA mix showed an improved split tensile and flexural strength by 2.92 and 6.26%, respectively. The microstructural analysis showed that the optimum mixture had a more condensed microstructure. Therefore, 30% replacement of MCRA can be incorporated in the characteristic strength of concrete of 30 MPa. In particular, MCRA incorporation had a positive influence similar to conventional concrete on the physical, mechanical, and microstructural properties, which can increase the utilization of all kinds of directly obtained construction and demolition wastes to increase the circular economy in the construction sector. [ABSTRACT FROM AUTHOR]

Insulating polymeric foams have an important role to play in increasing energy efficiency and therefore contributing to combating climate change. Their development in recent years has been driven towards the reduction of thermal conductivity and achievement of the required mechanical properties as main targets towards sustainability. This perception of sustainability has overseen the choice of raw materials, which are often toxic, or has placed research efforts on optimizing one constituent while the other necessary reactants remain hazardous. The transition to the circular economy requires a holistic understanding of sustainability and a shift in design methodology and the resulting research focus. This paper identifies research needs and possible strategies for polymeric foam development compatible with Circular Product Design and Green Engineering, based on an extensive literature review. Identified research needs include material characterization of a broader spectrum of polymer melt–gas solutions, ageing behavior, tailoring of the polymer chains, detailed understanding and modeling of the effects of shear on cell nucleation, and the upscaling of processing tools allowing for high and defined pressure drop rates. [ABSTRACT FROM AUTHOR]

Nowadays, special importance is given to quality control and food safety. Food quality currently creates significant problems for the industry and implicitly for consumers and society. The effects materialize in economic losses, alterations of the quality and organoleptic properties of the commercial products, and, last but not least, they constitute risk factors for the consumer's health. In this context, the development of analytical systems for the rapid determination of the sanitary quality of food products by detecting possible pathogenic microorganisms (such as Escherichia coli or Salmonella due to the important digestive disorders that they can cause in many consumers) is of major importance. Using efficient and environmentally friendly detection systems for identification of various pathogens that modify food matrices and turn them into food waste faster will also improve agri-food quality throughout the food chain. This paper reviews the use of metal nanoparticles used to obtain bio nanosensors for the purpose mentioned above. Metallic nanoparticles (Au, Ag, etc.) and their oxides can be synthesized by several methods, such as chemical, physical, physico-chemical, and biological, each bringing advantages and disadvantages in their use for developing nanosensors. In the "green chemistry" approach, a particular importance is given to the metal nanoparticles obtained by phytosynthesis. This method can lead to the development of good quality nanoparticles, at the same time being able to use secondary metabolites from vegetal wastes, as such providing a circular economy character. Considering these aspects, the use of phytosynthesized nanoparticles in other biosensing applications is also presented as a glimpse of their potential, which should be further explored. [ABSTRACT FROM AUTHOR]

In order to apply the concepts that allow the transition from a linear to a circular economy, waste generators and/or processors must identify those variants that generate products that can be used as secondary raw materials, thus also respecting the actions governing sustainable development. This paper presents such a variant, the briquetting of waste with high iron content, waste generated on current flows in steel enterprises or deposited in industrial sites. The obtained briquettes are analyzed for chemical and mechanical characteristics so that can be used as secondary materials in the steel production. An optimization of the chemical composition using generic algorithms is also proposed in order to obtain the mechanical characteristics necessary for the proper handling of these products. [ABSTRACT FROM AUTHOR]

The use of waste as an energy source in cement clinker production is a promising way to transition toward a circular economy and limit carbon dioxide (CO2) in the atmosphere. The cement industry is responsible for around 5% of global CO2 emissions. In this paper, the analysis of environmental and economic profits associated with the substitution of coal by two refuse-derived fuels (RDF) and sewage sludge (SS) in a cement kiln was presented. Differences in the fuel-related CO2 emissions were calculated for two-, three-, and four-component fuel blends based on the fuel consumption data, heating values, and the correspondent emission factors. The biogenic fraction content of 19% and 43% were measured in RDFs. The material balance of fuels with the assumed technological parameters of the cement clinker production installation (capacity of 6000 Mg per day and unit heat of 3.6 GJ) shows that the RDF heat substitution at the level of 90% allows for a saving of approximately 28.6 Mg per hour of coal, and to manage even approx. 40 Mg per hour of RDF. The increase in the share of SS in the total heat consumption to 6% contributed to reducing the actual emissions by 17 kg of CO2 per 1 Mg of clinker. Multilateral benefits due to the use of RDF in the cement plant were evident. [ABSTRACT FROM AUTHOR]

The explosive growth of the global market for Carbon-Fiber-Reinforced Polymers (CFRP) and the lack of a closing loop strategy of composite waste have raised environmental concerns. Circular economy studies, including Life Cycle Assessment (LCA) and Life Cycle Costing (LCC), have investigated composite recycling and new bio-based materials to substitute both carbon fibers and matrices. However, few studies have addressed composite repair. Studies focused on bio-based composites coupled with recycling and repairing are also lacking. Within this framework, the paper aims at presenting opportunities and challenges of the new thermosetting composite developed at the laboratory including the criteria of repairing, recycling, and use of bio-based materials in industrial applications through an ex ante LCA coupled with LCC. Implementing the three criteria mentioned above would reduce the environmental impact from 50% to 86% compared to the baseline scenario with the highest benefits obtained by implementing the only repairing. LCC results indicate that manufacturing and repairing parts built from bio-based CFRP is economically sustainable. However, recycling can only be economically sustainable under a specific condition. Managerial strategies are proposed to mitigate the uncertainties of the recycling business. The findings of this study can provide valuable guidance on supporting decisions for companies making strategic plans. [ABSTRACT FROM AUTHOR]

This is a bridge between circular economy issues and wood-based panels technology, especially particleboards. Because these composites contain a significant amount of non-wood raw material (10–12% thermoset resin, high hardness laminates, among others), their mechanical recycling leads to an uncontrollable reduction in produced particle size. This problem can be especially significant since the particleboards can be intended for multiple recycling due to the shortening of their service life. This research aimed to produce particles in the cycle of multiple re-milling particleboards and evaluate the selected properties of the produced particles and particleboards. Thus, the response to the following scientific problem can be given: what factors qualitatively and quantitatively influence the properties of the particleboards produced by multi-re-milled particles? The novelty of this research is the approach to recycling the raw materials from particleboards in fully controlled conditions, providing the characterization of produced particles and producing particleboards with close-to-industrial parameters, and, finally, evaluating the features of produced particleboards in the light of raw materials used. The results confirmed that subsequent mechanical recycling of particleboards, where the other panels are made entirely of second-milling particles, leads to an unprofitable and unacceptable reduction in the mechanical properties of the panels. The physical parameters, such as thickness swelling and water absorption, are improved, but this can be the result of increased content of chemical ingredients, which negatively influence the hygienic features of panels (emission of formaldehyde and total volatile organic compounds—TVOC). Further research should be directed towards estimating the optimal addition of mechanically recycled particles to particleboard production. [ABSTRACT FROM AUTHOR]

Plastic pollution has escalated into a critical global issue, with production soaring from 2 million metric tons in 1950 to 400.3 million metric tons in 2022. The packaging industry alone accounts for nearly 44% of this production, predominantly utilizing polyethylene terephthalate (PET). Alarmingly, over 90% of the approximately 1 million PET bottles sold every minute end up in landfills or oceans, where they can persist for centuries. This highlights the urgent need for sustainable management and recycling solutions to mitigate the environmental impact of PET waste. To better understand PET's behavior and promote its management within a circular economy, we examined its chemical and physical properties, current strategies in the circular economy, and the most effective recycling methods available today. Advancing PET management within a circular economy framework by closing industrial loops has demonstrated benefits such as reduced landfill waste, minimized energy consumption, and conserved raw resources. To this end, we identified and examined various strategies based on R-imperatives (ranging from 3R to 10R), focusing on the latest approaches aimed at significantly reducing PET waste by 2040. Additionally, a comparison of PET recycling methods (including primary, secondary, tertiary, and quaternary recycling, along with the concepts of "zero-order" and biological recycling techniques) was envisaged. Particular attention was paid to the heterogeneous catalytic glycolysis, which stands out for its rapid reaction time (20–60 min), high monomer yields (>90%), ease of catalyst recovery and reuse, lower costs, and enhanced durability. Accordingly, the use of highly efficient oxide-based catalysts for PET glycolytic degradation is underscored as a promising solution for large-scale industrial applications. [ABSTRACT FROM AUTHOR]

After more than two years wearing surgical masks due to the COVID-19 pandemic, used masks have become a significant risk for ecosystems, as they are producing wastes in huge amounts. They are a potential source of disturbance by themselves and as microplastic contamination in the water system. As 5500 tons of face masks are estimated to be used each year, there is an urgent need to manage them according to the circular economy principles and avoid their inadequate disposal. In this paper, surgical wear masks (WM), without any further pretreatment, have been introduced as addition to mortars up to 5% in the weight of cement. Mechanical and microstructural characterization have been carried out. The results indicate that adding MW to the cement supposes a decrease in the properties of the material, concerning both strength and durability behavior. However, even adding a 5% of WM in weight of cement, the aspect of the mortars is quite good, the flexural strength is not significantly affected, and the strength and durability parameters are maintained at levels that—even lower than the reference—are quite reasonable for use. Provided that the worldwide production of cement is around 4.1 Bt/year, the introduction of a 5% of WM in less than 1% of the cement produced, would make it possible to get rid of the mask waste being produced. [ABSTRACT FROM AUTHOR]

Conventionally, in a linear economy, C&D (Construction and Demolition) waste was considered as zero value materials, and, as a result of that, most C&D waste materials ended up in landfills. In recent years, with the increase in the awareness around sustainability and resource management, various countries have started to explore new models to minimize the use of limited resources which are currently overused, mismanaged, or quickly depleting. In this regard, the implementation of CE (Circular Economy) has emerged as a potential model to minimize the negative impact of C&D wastes on the environment. However, there are some challenges hindering a full transition to CE in the construction and demolition sectors. Therefore, this review paper aims to critically scrutinize different aspects of C&D waste and how CE can be integrated into construction projects. Reviewing of the literature revealed that the barriers in the implementation of CE in C&D waste sectors fall in five main domains, namely legal, technical, social, behavioral, and economic aspects. In this context, it was found that policy and governance, permits and specifications, technological limitation, quality and performance, knowledge and information, and, finally, the costs associated with the implementation of CE model at the early stage are the main barriers. In addition to these, from the contractors' perspective, C&D waste dismantling, segregation, and on-site sorting, transportation, and local recovery processes are the main challenges at the start point for small-scale companies. To address the abovementioned challenges, and also to minimize the ambiguity of resulting outcomes by implementing CE in C&D waste sectors, there is an urgent need to introduce a global framework and a practicable pathway to allow companies to implement such models, regardless of their scale and location. Additionally, in this paper, recommendations on the direction for areas of future studies for a reduction in the environmental impacts have been provided. To structure an effective model approach, the future direction should be more focused on dismantling practices, hazardous material handling, quality control on waste acceptance, and material recovery processes, as well as a incentivization mechanism to promote ecological, economic, and social benefits of the CE for C&D sectors. [ABSTRACT FROM AUTHOR]

The aim of this study was the characterization and evaluation of applicability as a soil amendment of biochar derived from rose pruning waste at different pyrolysis temperatures (200–500 °C) and process durations (20–60 min). The biochar properties were compared to the raw material. The biochars produced at 300 °C for 40 and 60 min demonstrated the best fuel properties. These variants showed high energy gain rates (77.6 ± 1.5% and 74.8 ± 1.5%, respectively), energy densification ratios (1.35 ± 0.00 and 1.37 ± 0.00, respectively), high heating values (24,720 ± 267 J × g−1 and 25,113 ± 731 J × g−1, respectively), and relative low ash contents (5.9 ± 0.5% and 7.1 ± 0.3%, respectively). Regarding fertilizer properties, such as pH value, ash content, heavy metal content, and pollutant elution, the biochars showed better qualities than the raw material. All tested biochar did not exceed the permissible values for heavy metals, including Cr, Cd, Ni, and Pb. The most optimal properties for soil amendments were noted for biochar variants of 400 °C for 40 min, 450 °C for 20 min, and 500 °C for 20 min. Generally, biochars produced at temperatures ≥400 °C did not inhibit root elongation, except for the material produced at 450 °C for 60 min (4.08 ± 23.34%). Biochars obtained at ≥300 °C showed a positive impact on seed germination (86.67 ± 18.48–100 ± 24.14%). [ABSTRACT FROM AUTHOR]

To address the growing global water demand, it is imperative to implement advanced treatment systems and sustainable alternatives for managing the large amount of waste generated during the water purification process, known as water treatment sludge (WTS). Worldwide, researchers and companies are exploring alternatives and methods for the valorization of WTS as a raw material in other processes. It is urgent that all productive sectors, which contribute significantly to greenhouse gas emissions, adopt this management principle to ensure more sustainable production, contributing to the global goal of climate neutrality. Notably, in civil construction, incorporating WTS as a supplementary cementitious material (SCM) shows great promise, considering that the industrial waste currently used for this purpose is increasingly restricted. The use of WTS as a raw material in the cement industry not only contributes to the reduction of the carbon footprint, but also reduces the high waste load still disposed of in landfills. The emerging applications for WTP sludge are reviewed, with emphasis on its valorization in the civil construction as an SCM. The main characteristics of this waste and their impacts on the environment are also addressed. [ABSTRACT FROM AUTHOR]

Considering recent climate changes, special importance is given to any attempt to depollute and protect the environment. A circular economy seems to be the ideal solution for the valorization of mineral waste, resulting from various industrial branches, by reintroducing them in the process of obtaining alternative building materials, more friendly to the environment. Geopolymers can be considered as a promising option compared to Portland cement. Information about the influence of the composition of the precursors, the influence of the activation system on the mechanical properties or the setting time could lead to the anticipation of new formulations of geopolymers or to the improvement of some of their properties. Reinforcement components, different polymers and expansion agents can positively or negatively influence the properties of geopolymers in the short or long term. [ABSTRACT FROM AUTHOR]

Growing environmental awareness has prompted a resurgence in traditional building techniques that rely on natural or recycled materials since many believe that structures made from these resources are ecologically friendly. Using Life Cycle Assessment (LCA) for construction materials offers valuable insights into the impacts produced during their production and construction processes. This study aims to assess the environmental impacts of two different constructions—an Earthbag Building (EB) and a conventional Sahrawi Cement Blocks Building (CBB). It also determines whether it is more environmentally beneficial to construct traditionally, utilizing local materials and aligning with the principles of the circular economy, which is one of the Sustainable Development Goals (SDGs) in Europe. This study specifically examines a cradle-to-gate LCA, using the software Simapro v. 9.4.0.1. Results show that in 21 out of the 22 impact categories analyzed, the CBB performs worse, in some cases presenting an impact of 70% higher than the EB. The highest impact is obtained for fine particulate matter formation and Global Warming related to Human Health categories, whilst impact categories related to water consumption and eutrophication obtained an impact of less than 0.001 for both constructions. [ABSTRACT FROM AUTHOR]

Due to a continuously developing population, our consumption of one of the most widely used building materials, concrete, has increased. The production of concrete involves the use of cement whose production is one of the main sources of CO2 emissions; therefore, a challenge for today's society is to move towards a circular economy and develop building materials with a reduced environmental footprint. This study evaluates the possibility of using new sustainable supplementary cementitious materials (SCMs) from waste such as recycled concrete aggregates (RCAs) and mixed recycled aggregates (MRAs) from construction and demolition waste, as well as bottom ash from olive biomass (BBA-OL) and eucalyptus biomass ash (BBA-EU) derived from the production of electricity. A micronisation pre-treatment was carried out by mechanical methods to achieve a suitable fineness and increase the SCMs' specific surface area. Subsequently, an advanced characterisation of the new SCMs was carried out, and the acquired properties of the new cements manufactured with 25% cement substitution in the new SCMs were analysed in terms of pozzolanicity, mechanical behaviour, expansion and setting time tests. The results obtained demonstrate the feasibility of using these materials, which present a composition with potentially reactive hydraulic or pozzolanic elements, as well as the physical properties (fineness and grain size) that are ideal for SCMs. This implies the development of new eco-cements with suitable properties for possible use in the construction industry while reducing CO2 emissions and the industry's carbon footprint. [ABSTRACT FROM AUTHOR]

This paper concerns the recovery of construction and demolition waste as coarse recycled aggregates for concrete. Coarse recycled aggregates may be used as a partial or total replacement of natural aggregates, contributing to the circular economy and minimizing landfill disposals as well as the consumption of natural mineral resources. However, construction and demolition waste is a heterogeneous material with undefined quality and the processing of this waste into recycled aggregates needs to ensure that the recycled aggregates have suitable properties for concrete. This paper summarizes several aspects related to coarse recycled aggregates, specifically addressing: (i) the typical composition of construction and demolition waste; (ii) the influence of different types of constituents on the properties of recycled aggregates and recycled aggregate concrete; (iii) requirements for recycled aggregates to be used in concrete; and (iv) production methods of recycled aggregates. It is argued that coarse recycled aggregates are a suitable construction material with adequate quality, even when common equipment is used in their production and preliminary separation as a key operation for ensuring the quality of the aggregates is recommended. [ABSTRACT FROM AUTHOR]

The global population is expected to increase by nearly 2 billion individuals over the next three decades, leading to a significant surge in waste generation and environmental challenges. To mitigate these challenges, there is a need to develop sustainable solutions that can effectively manage waste generation and promote a circular economy. Mycelium-based composites (MBCs) are being developed for various applications, including packaging, architectural designs, sound absorption, and insulation. MBCs are made by combining fungal mycelium with organic substrates, using the mycelium as a natural adhesive. Mycelium, the vegetative part of fungi, can be grown on various organic feedstocks and functionalized into a range of diverse material types that are biobased and thus more sustainable in their production, use, and recycling. This work aims to obtain mycelium-based composites with acoustic absorption properties, using coffee grounds and agricultural waste as raw materials. The topic approached presents a new method of recovering spent coffee grounds that does not involve high production costs and reduces two current environmental problems: noise pollution and abundant waste. Measurements of the normal-incidence sound absorption coefficient were presented and analyzed. Mycelium-based composites offer an innovative, sustainable approach to developing bio-composite sound-absorbing surfaces for interior fittings. The material by Ganoderma lucidum exhibits exceptional sound-absorbing properties at frequencies below 700 Hz, which is a crucial aspect of creating sound-absorbing materials that effectively absorb low-frequency sound waves. The modular construction system allows for a high degree of flexibility to adapt to short-term changes in the workplace. [ABSTRACT FROM AUTHOR]

Reduction of emissions, energy consumption, and use of substitutes for natural resources is an element of sustainable development and the circular economy. Cement production is a process with a high carbon footprint; therefore, minimizing the use of this material has a significant impact on reducing environmental costs. A substitute for cement is municipal solid waste incineration fly ash (MSWIFA). The article presents a method of making an eco-concrete with the use of municipal solid waste incineration hazardous fly ash. The use of secondary waste for the production of building materials additionally contributes to achieving climate neutrality established by the European Union and China. The article analyzes the physicochemical properties of various MSWIFAs, the amount and leachability of heavy metals, and selected elements from MSWIFA and concrete properties. The technical properties of mortars containing MSWIFA were investigated. Consistency is not affected by MSWIFA content, although the workability time is prolonged. Air entraining admixture efficiency is lowered, but the effect lasts longer. The initial setting time is prolonged, and the flexural and compressive strengths are decreased in early terms because of the zinc presence in MSWIFA. MSWIFA does not influence the water demand, volume stability of mortars, or microstructure of cement's hydration products. [ABSTRACT FROM AUTHOR]

Slags and ashes generated in thermal waste treatment facilities require proper management. In line with the principles of the circular economy, new, more economical, and ecological possibilities for utilizing these substances are sought. These waste materials exhibit characteristics similar to rocks in many aspects. This study focuses on analyzing the similarities and differences between nine selected rocks and three samples of slags and ashes obtained from municipal waste incineration. The main research device used was a polarizing microscope, using reflected, transmitted, and fluorescent light. Additionally, low-pressure gas adsorption equipment, as well as helium and quasi-liquid pycnometers, were used for complementary analysis. The parameters analyzed mainly covered broadly defined petrographic properties of rocks and slags, with a particular emphasis on porosity, porous structure, and the spatial distribution of pores and fractures. The conducted analyses confirmed a significant similarity between slags and ashes and clastic sedimentary rocks such as sandstones and mudstones. The research results underscore the importance of petrographic microscopic studies for analyzing materials other than rocks. They also allow for exploring applications for slags and ashes in areas traditionally reserved for natural rock resources. The findings also indicate the necessity of using methods other than microscopic ones to describe the pore space of rocks. The lower measurement range of the optical microscope is limited to approximately 1 μm, covering only macropores. Other methods extend this characteristic to micro- and mesopores. Therefore, a combination of different methods is often employed to obtain a more comprehensive characterization of rock porosity. [ABSTRACT FROM AUTHOR]

The following research aims to investigate selected properties of three-layer plywood, manufactured using dust from the milling of three-layer particleboard as a filler in the bonding mass. Four types of fillers were considered in the study: commercial rye flour, wood dust naturally occurring in the composition of particles used industrially for particleboard production, wood dust from the first batch of shredded particleboard, and dust from the second round of milled particleboard. The highest modulus of elasticity (MOE) values were observed for the reference samples. Notably, in the samples containing filler sourced from the secondary milling of particleboard, the MOE exhibited an upward trend in conjunction with increasing filler content. The modulus of rupture (MOR) decreased with an elevated degree of filler milling from 73.1 N mm−2 for the native filler, through to 68.9 N mm−2 for the filler after 1st milling, and to 54.5 N mm−2 for the filler after 2nd milling (with 10 parts per weight (pbw) of filler used as an reference), though it increased slightly as the filler content increased. The most favorable outcomes in shear strength were achieved in samples containing filler material from the initial milling of particleboard. The thickness swelling peaked in variants utilizing filler material from both the initial and secondary milling of particleboards (20.1% and 16.6% after 24 h of soaking for samples with 10 pbw filler after the 1st and 2nd milling, respectively, compared to 13.0% for the reference samples). Water absorption testing exhibited a more pronounced response in the newly introduced variants, although the samples containing filler from the initial and secondary milling processes eventually yielded results akin to the reference sample, with naturally occurring dust displaying higher water absorption values. The highest density values (about 1224 kg m−3) were observed in the reference samples. A similar density profile was recorded for samples with five parts of wood flour as filler, although the density of the bonding line was slightly lower in these instances (1130 kg m−3). This research confirms the feasibility of applying the aforementioned dust as an alternative to conventional fillers in plywood technology. It also raises the question of how to effectively remove glue residues from wood-based composite dust, which would enhance their absorption properties. [ABSTRACT FROM AUTHOR]

This study aims to assess the effect of adding lignin waste, a by-product of bioethanol production from forest biomass, to asphalt concrete to improve its performance. After adjusting the lignin content based on preliminary Marshall tests, 20% of this by-product by mass of bitumen was added to the asphalt concrete blends via the dry method. This lignin content was suitable to the temperature was decreased 40 °C compared to the usual mixing temperature, thus allowing the production of warm-mix asphalt concrete (WMA) without any other additive. Tests on a gyratory compactor assessed the workability of the studied asphalt concrete, allowing us to obtain these findings. Moreover, lignin improved moisture damage and adhesion resistance between the binder film and the aggregate particles' surface. The behaviour at high temperatures was also enhanced, resulting in better resistance to permanent deformation. These promising laboratory results show us an opportunity to create value for this type of by-product in substituting commercial additives for asphalt concrete, such as organic wax or adhesion promoters, to allow the production of warm-mix asphalt concrete with improved properties. [ABSTRACT FROM AUTHOR]

Currently, the growing demand for polymeric materials has led to an increased need to develop effective recycling methods. This study focuses on the multiple processing of bio-based thermoplastic polyurethane elastomers (bio-TPUs) as a sustainable approach for polymeric waste management through mechanical recycling. The main objective is to investigate the influence of two reprocessing cycles on selected properties of bio-TPUs. Two series of bio-based TPUs were synthesized via a solvent-free two-step method with the use of hexamethylene diisocyanate or hexamethylene diisocyanate/partially bio-based diisocyanate mixtures, bio-based poly(triamethylene ether) glycol, and bio-based 1,3 propanediol. Both the raw bio-TPUs and those subjected to two reprocessing cycles were examined with respect to their chemical, physical, thermal, thermomechanical, and mechanical properties. The conducted research revealed that reprocessing led to changes in the phase separation between the hard and soft segments, thereby affecting the bio-TPUs' properties. Both series of materials showed similar chemical structures regardless of reprocessing (slight changes were observed in the range of carbonyl peak). The thermal properties of TPUs exhibited slight differences after each reprocessing cycle, but generally, the non-processed and reprocessed bio-TPUs were thermally stable up to about 300 °C. However, significant differences were observed in their mechanical properties. The tensile strength increased to 34% for the twice-reprocessed bio-TPUs, while the elongation at break increased by ca. 200%. On the other hand, the processing cycles resulted in a decrease in the hardness of both bio-TPU series (ca. 3–4 °ShA). As a result, the prepared bio-TPUs exhibited characteristics that were closer to those of the sustainable materials model, promoting the circular economy of plastics, with environmental benefits arising from their recyclability and their high content of bio-based monomers (78.4–78.8 wt.%). [ABSTRACT FROM AUTHOR]

The technological, social and economic development observed in recent decades brought an exponential increase in consumption and inherent new challenges. Recycling is one of the best solutions to minimize the environmental impact of raw materials. However, multi-material components are difficult or even impossible to recycle. The present work focuses on the reduction in the number of different materials used in multifunctional components. In particular, it intends to assess the potential of injecting molding grades of polypropylene (PP) to produce parts with transparency (haze) gradients. Firstly, several polypropylene grades of different types were identified and injected under various thermal processing conditions, i.e., injection temperature and mold temperature, in order to vary the cooling rate, influencing the growth rate of the spherulites and eventually the presence/absence of α and β crystalline zones. The injected parts' optical properties were then characterized, and the most promising PP grades were identified and selected for subsequent work, namely grade DR 7037.01, showing the widest range of haze (from 29.2 to 68.7%). and PP070G2M, presenting the highest haze value (75.3%). Finally, in an attempt to understand the origin of the haze variations observed, the parts injected with the selected PP grades were further characterized through differential scanning calorimetry (DSC) and polarized light microscopy. It was concluded that the main factor causing the observed haze difference was, apart from the size of the spherulites, the presence of internal layers with different birefringence and, therefore, different refractive indices. [ABSTRACT FROM AUTHOR]

Increasing year-by-year vehicle production is related to the expanding volume of used tires; therefore, exploring waste management strategies is strongly recommended. The global tire market reached 2.27 billion units in 2021 and is expected to reach 2.67 billion units by 2027. Dumping tires in landfills can cause significant environmental impacts, so waste tire utilisation plays an important role. Predominantly, the following three directions are employed for waste tire disposal: retreading, energy recovery and material recovery. The review shows that used tires can remove environmental pollution from both aqueous solutions containing heavy metal ions, dyes, pharmaceutical compounds, and benzene, toluene, ethylbenzene and xylene (BTEX). Particularly high efficiency was achieved in the removal of dyes (72%), taking into account the high initial concentration of impurities. The adsorption process depends on multiple factors, including, in particular, the following: pH, initial concentration of pollution, contact time and the properties of the sorbent used. The optimal pH range was identified to be between 6 and 7. Considering the principles of circular economy as well as based on the current state of knowledge, it can be concluded that the solid fraction obtained from the combustion of waste tires can be practically utilised for various environmental purposes. [ABSTRACT FROM AUTHOR]

The shredding of end-of-life refrigerators produces every year in Italy 15,000 tons of waste polyurethane foam (PUF), usually destined for energy recovery. This work presents the results of the investigation of the oil sorption potential of waste PUF according to ASTM F726–17 standard. Three oils (diesel fuel and two commercial motor oils) having different densities (respectively, 0.83, 0.87, and 0.88 kg/dm3) and viscosities (respectively, 3, 95, and 140 mm2/s at 40 °C) were considered. The waste PUF was sampled in an Italian e-waste treatment plant, and its characterization showed 16.5 wt% particles below 0.71 mm and 13 wt% impurities (paper, plastic, aluminum foil), mostly having dimensions (d) above 5 mm. Sieving at 0.071 mm was applied to the waste PUF to obtain a "coarse" (d > 0.71 mm) and a "fine" fraction (d < 0.71 mm). Second sieving at 5 mm allowed an "intermediate" fraction to be obtained, with dimensions between 0.71 and 5 mm. The oil sorption tests involved the three fractions of waste PUF, and their performances were compared with two commercial oil sorbents (sepiolite and OKO-PUR). The results of the tests showed that the "fine" PUF was able to retain 7.1–10.3 g oil/g, the "intermediate" PUF, 4.2–7.4 g oil/g, and the "coarse" PUF, 4.5–7.0 g oil/g, while sepiolite and OKO-PUR performed worse (respectively, 1.3–1.6 and 3.3–5.3 g oil/g). In conclusion, compared with the actual management of waste PUF (100 wt% sent to energy recovery), the amount destined directly to energy recovery could be limited to 13 wt% (i.e., the impurities). The remaining 87 wt% could be diverted to reuse for oil sorption, and afterward directed to energy recovery, considered as a secondary option. [ABSTRACT FROM AUTHOR]

Concrete, as one of the essential construction materials, is responsible for a vast amount of emissions. Using recycled materials and gray water can considerably contribute to the sustainability aspect of concrete production. Thus, finding a proper replacement for fresh water in the production of concrete is significant. The usage of industrial wastewater instead of water in concrete is considered in this paper. In this study, 450 concrete samples are produced with different amounts of wastewater. The mechanical parameters, such as slump, compressive strength, water absorption, tensile strength, electrical resistivity, rapid freezing, half-cell potential and appearance, are investigated, and a specific concentration and impurities of wastewater that cause a 10% compressive strength reduction were found. The results showed that the usage of industrial wastewater does not significantly change the main characteristics of concrete. Although increasing the concentration of wastewater can decrease the durability and strength features of concrete nonlinearly, the negative effects on durability tests are more conspicuous, as utilizing concentrated wastewaters disrupt the formation of appropriate air voids, pore connectivity and pore-size distribution in the concrete. [ABSTRACT FROM AUTHOR]

This research investigates the feasibility of developing clay composites using natural materials and incorporating waste by-products suitable for plastering diverse support structures. The study identified a versatile composition suitable for a wide range of support materials and explored the potential of revaluing industrial waste and by-products by reintegrating them into the Circular Economy. The experimental investigation outlines the process of evaluating the influence of different raw materials on the performance of the clay composite. The findings confirm that using limestone sludge and fly ash as additives to clay contributes to reducing axial shrinkage and increasing mechanical strengths, respectively. The optimal percentage of additives for the clay used are identified and provided. Using hydraulic lime as a partial substitute for clay reduces the apparent density of dried clay composites, axial shrinkage, and fissures formation while improving adhesion to the substrate. Introducing dextrin into this mix increases the apparent density of the hardened plaster while keeping axial shrinkage below the maximum threshold indicated by the literature. Mechanical strengths improved, and better compatibility in terms of adhesion to the support was achieved, with composition S3 presenting the best results and a smooth, fissure-free plastered surface after drying. [ABSTRACT FROM AUTHOR]

The demand for geopolymer materials is constantly growing. This, in turn, translates into an increasing number of studies aimed at developing new approaches to the methodology of geopolymer synthesis. The range of potential applications of geopolymers can be increased by improving the properties of the components. Future directions of studies on geopolymer materials aim at developing geopolymers showing excellent mechanical properties but also demonstrating significant improvement in thermal, magnetic, or sorption characteristics. Additionally, the current efforts focus not only on the materials' properties but also on obtaining them as a result of environment-friendly approaches performed in line with circular economy assumptions. Scientists look for smart and economical solutions such that a small amount of the modifier will translate into a significant improvement in functional properties. Thus, special attention is paid to the application of nanomaterials. This article presents selected nanoparticles incorporated into geopolymer matrices, including carbon nanotubes, graphene, nanosilica, and titanium dioxide. The review was prepared employing scientific databases, with particular attention given to studies on geopolymer nanocomposites. The purpose of this review article is to discuss geopolymer nanocomposites in the context of a sustainable development approach. Importantly, the main focus is on the influence of these nanomaterials on the physicochemical properties of geopolymer nanocomposites. Such a combination of geopolymer technology and nanotechnology seems to be promising in terms of preparation of nanocomposites with a variety of potential uses. [ABSTRACT FROM AUTHOR]

Blast Oxygen Furnace (BOF) slag represents one of the largest waste fractions from steelmaking. Therefore, slag valorisation technologies are of high importance regarding the use of slag as a secondary resource, both in the steel sector and in other sectors, such as the construction or cement industries. The main issue regarding the use of BOF slag is its volumetric instability in the presence of water; this hampers its use in sectors and requires a stabilisation pre-treatment. These treatments are also cost-inefficient and cause other environmental issues. This paper analyses the use of untreated BOF slag from a technical and environmental point of view, suggesting it as an alternative to natural aggregates in road surface layers and asphalt pavements. A comprehensive analysis of the requirements to be met by raw materials used in asphalt mixes was performed, and a pilot test was carried out with two different mixtures: one mix with limestone as coarse aggregate and another with 15% BOF slag. Furthermore, the global warming impacts derived from each mix with different aggregates were measured by Life Cycle Analysis (LCA), and a transport sensitivity analysis was also performed. The results show how the utilization of BOF slag as coarse aggregate in road construction improves the technical performance of asphalt mixtures (Marshall Quotient 4.9 vs. 6.6). Moreover, the introduction of BOF slag into the asphalt mix as a coarse aggregate, instead of limestone, causes a carbon emissions reduction rate of more than 14%. [ABSTRACT FROM AUTHOR]

There has been increasing interest in green and recyclable materials to promote the circular economy. Moreover, the climate change of the last decades has led to an increase in the range of temperatures and energy consumption, which entails more energy expenditure for heating and cooling buildings. In this review, the properties of hemp stalk as an insulating material are analyzed to obtain recyclable materials with green solutions to reduce energy consumption and reduce noise to increase the comfort of buildings. Hemp stalks are a low-value by-product of hemp crops; however, they are a lightweight material with a high insulating property. This study aims to summarize the research progress in materials based on hemp stalks and to study the properties and characteristics of the different vegetable binders that could be used to produce a bio-insulating material. The material itself and its microstructural and physical aspects that affect the insulating properties are discussed, as is their influence on durability, moisture resistance, and fungi growth. Research suggests using lignin-based or recyclable cardboard fiber to develop a bio-composite material from hemp stalk, but long-term stability requires further investigation. [ABSTRACT FROM AUTHOR]

The widespread use of geopolymer cement (GPC) has been hindered by a lack of scientific knowledge that still exists regarding its synthesis process. Key points, such as the release of aluminosilicate species from the raw materials and its link to the properties of GPC, have still not been completely studied. As a result, most of the GPC formulations covered in the literature are based on precursors' elemental analysis using XRF (X-ray Fluorescence), or other equivalent analysis methods, and consider that the total aluminosilicate content of the precursors is available for participating in the geopolymerization process, which seems very unlikely. In this study, the amounts of aluminate and silicate species released from metakaolin (MK), electric arc furnace slag (EAFS), and biomass fly ash (BFA) in alkaline dissolution tests were determined by simple spectrophotometric methods. It was found that MK yields the highest aluminosilicate dissolution amount, about 2.1 mmol of silicate + aluminate per gram of MK, while EAFS and BFA yield about 0.53 and 0.32 mmol/g precursor, respectively. These results were used to estimate the total amounts of dissolved aluminosilicates in a series of GPC mortars prepared from these raw materials, which were thereafter subjected to mechanical tests. It was shown that the mortars' compressive strength (which ranged from 1 to 63 MPa) is linearly correlated with their estimated total amount of dissolved aluminosilicates, with the best linear fit yielding a coefficient of determination above 0.99. It was concluded that by using the results of the dissolution tests, the estimation of compressive strength is greatly improved when compared to using the elemental analysis obtained by XRF, which yields a coefficient of determination of 0.88 and a larger dispersion of data points. The results reveal the usefulness of this simple method for evaluating the potential of inorganic industrial waste streams as precursors for GPC. [ABSTRACT FROM AUTHOR]

Selective laser sintering (SLS) is currently in transition to the production of functional components. However, the ability to apply it is confronted with new requirements for reliability and reproducibility. Therefore, an in-depth understanding of aging processes in polymers is essential. Regarding material traceability as well as defective component identification with subsequent cause tracing, the application of a material-inherent marking technology represents a solution. SLS in combination with modified polymers as a marking technology proves to be an efficient opportunity to produce reproducible and high-quality components due to an increased understanding of the process. Based on a selection of modified polymers for use in SLS, which were characterized in part I of the study, this work focuses on the experimental validation of the result. The influence of modified polymers on materials and component properties and the SLS process's influence on the traceability of modified polymers are examined. Intrinsic and extrinsic material properties as well as mechanical properties, surface quality and sinter density are analyzed. No discernible influences of the modified polymers on the investigated properties could be observed and the traceability of the modified polymers could also be confirmed in the aged powder and component using mass spectroscopy. [ABSTRACT FROM AUTHOR]

Waste fly ash, with both low (with the addition of vermiculite) and high contents of unburned coal, were subjected to hydrothermal syntheses aiming to obtain zeolite composite materials—zeolite + vermiculite (NaX–Ver) and zeolite + unburned carbon (NaX–C). The composites were compared with parent zeolite obtained from waste fly ash with a low content of unburned carbon (NaX–FA). In this study, the physicochemical characteristics of the obtained materials were evaluated. The potential application of the investigated zeolites for the adsorption of ammonium ions from aqueous solutions was determined. Composite NaX–Ver and parent zeolite NaX–FA were characterized by comparable adsorption capacities toward ammonium ions of 38.46 and 40.00 mg (NH4+) g−1, respectively. The nearly 2-fold lower adsorption capacity of composite NaX–C (21.05 mg (NH4+) g−1) was probably a result of the lower availability of ion exchange sites within the material. Adsorbents were also regenerated using 1 M NaCl solution at a pH of 10 and subjected to 3 cycles of adsorption–desorption experiments, which proved only a small reduction in adsorption properties. This study follows the current trend of waste utilization (fly ash) and the removal of pollutants from aqueous solutions with respect to their reuse, which remains in line with the goals of the circular economy. [ABSTRACT FROM AUTHOR]