Search

The direct wave between the transceiver antenna negatively affects the dynamic range and imaging quality of ground penetrating radar (GPR). Suppressing this direct wave is a vital problem in enhancing the performance of the whole GPR system. In this paper, a Minkowski-fractal metamaterial absorber (MMA) with the resistive film is proposed in the GPR transceiver antenna to reduce the mutual coupling. The simulated and measured results indicate that this MMA has an effective wideband absorption in 1.0-8.0 GHz. And the thickness of MMA is only 0.007 λ 0 (with respect to 2.0 GHz). This wideband MMA can reduce the mutual coupling of the proposed GPR transceiver antenna by an average of 10 dB. And it also mitigates the time-domain ringing problem of the transmit antenna. Real-world experiments demonstrate that the direct wave from the transmitting antenna can be reduced and the target echo arriving at the receiving antenna can be increased if this MMA is placed in the proposed transceiver antenna. This resistive film-based MMA offers great promise in realizing low-cost, compact, and lightweight GPR antennas, which can also be extended to high-frequency microwave imaging. [ABSTRACT FROM AUTHOR]

Hot compression tests were performed with strain rates (0.01–10 s−1) and temperatures (850–1150 °C). The power law relationship between the critical stress and critical strain and Zener–Hollomon parameters was determined by θ-σ curves. Microstructure was investigated by electron backscattered diffraction. The results showed that the flow behavior and microstructure of 35CrMo steel was affected by ultrasonic-assisted casting. The activation energy of non-ultrasonic and ultrasonic-assisted 35CrMo steel were 410 ± 9.9 and 386 ± 9.4 kJ/mol, respectively, and the activation energy of ultrasonic-assisted specimens was reduced by 6%. In addition, the ultrasonic-assisted treatment refines the grains to some extent and makes the softening process of ultrasonic-assisted samples progress faster, which promoted the development of dynamic recrystallization and the production of Σ3 boundaries. The discontinuous dynamic recrystallization was the main DRX nucleation mechanism of the 35CrMo steel. [ABSTRACT FROM AUTHOR]

The effects of ultrasonic introduced by L-shaped sonotrodes made of high-temperature-resistant ceramic on the microstructure and macro-segregation of solidifying 15t AA2219 aluminum alloy ingots have been examined in the present study. The macroscopic morphology of the corrosion of the sonotrode has been observed. Grain refinement has been observed, the shape and size of the precipitated phase of the ingot were counted, and the degree of segregation along the transverse direction at 500 mm from the head of the ingot has been evaluated. The results reveal that the L-shaped ceramic ultrasonic introduction device can effectively avoid the erosion of high-temperature melt on the sonotrode and the heat radiation of the high-temperature heat flow to the transducer. Furthermore, the scanning electron microscope (SEM) and chemical composition detection results also indicate that the inter-dendritic micro-segregation of the equiaxed grains can be reduced, and the macro-segregation of the chemical composition of the ingot can be suppressed, and more homogeneous microstructures can be obtained when ultrasonic has been applied during solidification. [ABSTRACT FROM AUTHOR]

The effect of deep cryogenic treatment on microstructure and wear resistance of LC3530 Fe-based powder laser cladding coating was investigated in this paper. The cladding coating was subjected to deep cryogenic treatment for the different holding times of 3, 6, 9, 12, and 24 h, followed by tempering at room temperature. Microstructure of the cladding coating was observed by optical microscope (OM) and the microhardness was measured by the Vickers-hardness tester. The wear was tested by ball and flat surface grinding testing conducted on the material surface comprehensive performance tester. The wear scars were analyzed using a non-contact optical surface profiler and scanning electron microscope (SEM). The results showed the grain size of cladding coating after 12 h of deep cryogenic treatment was significantly reduced by 36.50% compared to the non-cryogenically treated cladding coating, and the microhardness value increased by approximately 34%. According to the wear coefficient calculated by the Archard model, the wear resistance improved about five times and the wear mechanism was micro-ploughing. The deep cryogenic treatment could enhance the wear resistance of the cladding coating by forming a wear resistant alloy compound and higher surface microhardness. [ABSTRACT FROM AUTHOR]

CoCrCuFeMnNix (x = 0, 0.5, 1.0, 1.5, 2.0 mol, named as Ni0, Ni0.5, Ni1.0, Ni1.5, and Ni2.0, respectively) high-entropy alloy powders (HEAPs) were prepared via mechanical alloying (MA), and XRD, SEM, EDS, and vacuum annealing were used to study the alloying behavior, phase transition, and thermal stability. The results indicated that the Ni0, Ni0.5, and Ni1.0 HEAPs were alloyed at the initial stage (5–15 h), the metastable BCC + FCC two-phase solid solution structure was formed, and the BCC phase disappeared gradually with the prolonging of ball milling time. Finally, a single FCC structure was formed. Both Ni1.5 and Ni2.0 alloys with high nickel content formed a single FCC structure during the whole mechanical alloying process. The five kinds of HEAPs showed equiaxed particles in dry milling, and the particle size increased with an increase in milling time. After wet milling, they changed into lamellar morphology with thickness less than 1 μm and maximum size less than 20 μm. The composition of each component was close to its nominal composition, and the alloying sequence during ball milling was Cu→Mn→Co→Ni→Fe→Cr. After vacuum annealing at 700~900 °C, the FCC phase in the HEAPs with low Ni content transformed into FCC2 secondary phase, FCC1 primary phase, and a minor σ phase. The thermal stability of HEAPs can be improved by increasing Ni content. [ABSTRACT FROM AUTHOR]

Self-assembled submicron nickel particles were successfully synthesized via the one-step surfactant-assisted solvothermal method. The impact of surfactant and reducing agent stoichiometry is investigated in this manuscript. Different morphologies and structures of Ni particles, including flower-like nanoflakes, hydrangea-like structures, chain structures, sphere-like structures, and hollow structures were prepared through different processing conditions with two parameters such as temperature and time. Based on scanning electron microscopy (SEM), X-ray diffraction (XRD), thermal gravimetric analysis (TGA) and vibrating sample magnetometry (VSM), the submicron nickel particles show good saturation magnetization and excellent thermal stabilities with a possible growth mechanism for the variety of the structure-tuned formation. Importantly, the microwave absorption properties of the submicron nickel particles were studied. The lowest reflection loss of Ni-P9/T200/H15 with a thin layer thickness of 1.7 mm can reach -42.6 dB at 17.3 GHz. [ABSTRACT FROM AUTHOR]

Hot deformation experiments of as-cast 35CrMoV steel, with strain rates of 0.01 s−1 and 10 s−1, deformation temperatures of 850, 950, and 1050 °C, and an extreme deformation reaching 50%, were carried out using a Gleeble-3810 thermal simulator. Electrochemical corrosion experiments were conducted on the deformed specimens. The microstructure was observed by optical microscope (OM), and the corrosion morphology and corrosion products of the specimens were investigated by scanning electron microscopy (SEM), energy disperse spectroscopy (EDS), confocal laser scanning microscopy (CLSM), and X-ray diffraction (XRD) techniques. The results show that the grain size increased gradually with an increase in the deformation temperature at the same strain rate, whereas the corrosion resistance deteriorated. At the same deformation temperature, the grain size becomes smaller as the strain rate increases, which enhances the corrosion resistance. This is mainly attributed to the fine grains, which can form more grain boundaries, increase the grain boundary area, and accelerate the formation of the inner rust layer at the beginning of corrosion. Moreover, fine grains can also refine the rust particles and enhance the bonding strength between the inner rust layer and the matrix. The denseness and stability of the inner rust layer increases as the corrosion process progresses, thereby improving corrosion resistance. [ABSTRACT FROM AUTHOR]