Search

The addition of superelastic shape memory alloy fibers (SMAF) into engineering cementitious composites (ECC) can create a new type of SMAF-ECC composite material with good self-recovery and energy dissipation performance, which is very suitable for seismic structures. In this study, 10 groups of beam specimens with different volume contents of SMAF were fabricated, and the bending performance, deflection recovery and energy dissipation ability of these beams were studied through three-point bending cyclic loading tests. The failure mode, peak load, load–deflection curve, crack width and other indicators of the specimens were analyzed, and the relationship expression between fiber content and bending strength was established by fitting analysis. The results show that adding SMA fibers can significantly improve the peak load of ECC beams, with a maximum increase of 48.31%. The knotted SMA fibers can fully exert their superelasticity, providing the beam specimens with crack self-closing and deflection recovery ability. When the volume content of SMA fibers is 0–0.6%, the bending strength, energy dissipation ability and deflection recovery ability of the composite material beams increase with the increase in fiber content. When the volume content of SMA fibers is 0.6–1.0%, the above indicators decrease with the increase in fiber content. The suggested equations can well reflect the relationship between fiber content and beam bending strength. The research results of this paper provide theoretical support for the engineering application of SMAF-ECC composite materials. [ABSTRACT FROM AUTHOR]

Combining Engineered Cementitious Composites (ECC) with shape memory alloy (SMA) fibers can form SMA fiber reinforced ECC (SMAF-ECC) that has excellent deformation recovery and energy dissipation capabilities. Substituting some of the tensioned concrete with this new composite material, along with steel bars, is expected to significantly improve the seismic energy dissipation and self-recovery capabilities of traditional reinforced concrete components. However, a reliable bond between steel bars and SMAF-ECC is critical to ensure their synergistic performance. In this paper, the failure mode and bond strength of steel bars and SMAF-ECC were studied through direct tensile tests, and the influence factors such as steel bar diameter, bond length, and SMAF volume fraction were analyzed. A bond-slip constitutive model for steel bars and SMAF-ECC was proposed. The results show that the failure mode of the tensile test specimens is mainly steel bar pull-out failure; the incorporation of SMAF significantly enhances the bond strength between the steel bar and matrix; increasing the steel bar diameter and bond length both lead to a decrease in bond strength while increasing the SMAF volume fraction can significantly increase the bond strength. Among them, the specimen with a steel bar diameter of 12 mm, bond length of 70 mm, and SMAF volume fraction of 0.5% has the largest increase in bond strength, reaching 52.96%. The proposed improved bond-slip constitutive model is in good agreement with the bond-slip curve obtained in the experiments, with a determination coefficient of 0.99. The research results of this paper provide an important theoretical basis for promoting the engineering application of SMAF-ECC materials. [ABSTRACT FROM AUTHOR]

SMAF-ECC material composed of shape memory alloy fiber (SMAF) and engineered cementitious composite (ECC) has good bending and tensile properties, as well as good crack self-healing ability, energy consumption, and self-centering ability. The bond behavior between fiber and matrix is crucial to the effective utilization of the superelasticity of SMAF. The experimental study considered three variables: SMA fiber diameter, fiber end shape, and bond length. The pullout stress–strain curve of SMAF was obtained, and the maximum pullout stress, maximum bond stress, and fiber utilization rate were analyzed. Compared with the straight end and the hook end, the maximum pullout stress of the specimen using the knotted end SMAF is above 900 MPa, the fiber undergoes martensitic transformation, and the fiber utilization rate is above 80%, indicating that the setting of the knotted end can give full play to the superelasticity of the SMAF. Within the effective bond length range, increasing the bond length can increase the maximum anchorage force of the knotted end SMAF. Increasing the fiber diameter can increase the maximum pullout stress and maximum anchoring force of the knotted end SMAF but reduce the utilization rate of SMA fiber. This study provides a reliable theoretical basis for the bonding properties between SMAF and ECC. [ABSTRACT FROM AUTHOR]

The incorporation of superelastic shape memory alloy (SMA) fibers into engineered cementitious composite (ECC) materials can provide high seismic energy dissipation and deformation self-centering capabilities for ECC materials. Whether the SMA fibers can be sufficiently bonded or anchored in the ECC matrix and whether the mechanical properties of the SMA fibers in the ECC matrix can be effectively utilized are the key scientific issues that urgently need to be studied. In order to study the mechanical behavior of SMA fiber embedded in ECC matrix, four groups of semi-dog-bone pullout specimens were fabricated, and the cyclic pullout tests were conducted in this paper. The pullout stress, displacement, and self-centering capability were analyzed, and different influencing factors were discussed. The results show that the knotted ends can provide sufficient anchorage force for SMA fibers, and the maximum pullout stress of SMA fiber can reach 1100 MPa, thus the superelasticity can be effectively stimulated. The SMA fibers show excellent self-centering capability in the test. The minimum residual deformation in the test is only 0.29 mm, and the maximum self-centering ratio can reach 0.93. Increasing bond length can increase the ultimate strain of SMA fibers with knotted ends, but reduce the maximum pullout stress. Increasing fiber diameter can increase both the ultimate strain and the maximum stress of knotted end SMA fibers. While neither bond length nor fiber diameter has significant effect on the self-centering ratio. This paper provides a theoretical basis for further study of the combination of SMA fibers and ECC materials. [ABSTRACT FROM AUTHOR]