Search

The tribological behavior of traditional oil-in-water (O/W) lubricants (1.0 wt.%) and nano-TiO2 additive lubricants (1.0–9.0 wt.%) during micro rolling of titanium foils were analyzed. In this study, the surface morphologies of titanium foils under various lubrication conditions were assessed, and the corresponding lubrication mechanisms were revealed. The tribological behavior of nano-TiO2 additive lubricants during micro rolling of titanium foils was also explored through a series of characterization methods. The utilization of nano-TiO2 additive lubricants in micro rolling reduces the surface roughness of titanium foils. Moreover, it effectively inhibits the generation of indentations and cracks during rolling processes, enhancing the surface quality of rolled specimens. Additionally, owing to the synergism of rolling, tribo-film, mending and polishing effects of the nanoparticles, both the rolling force and surface roughness were minimized by using lubricants containing 3.0 wt.% TiO2 nanoparticles. Overall, an optimal concentration (3.0 wt.%) of TiO2 nanoparticles in water-based nanolubricants was obtained with enhanced tribological properties and lubrication performance during micro rolling of titanium foils. [ABSTRACT FROM AUTHOR]

A novel design method based on a novel origami process that can create a solid structure swiftly and at a low cost is presented for rectangular waveguide-type microwave devices in this paper. A planar structure was fabricated by the lamination and laser cutting of polystyrene membranes and aluminum foils and was converted into a solid structure via origami in accordance with the selective absorption of infrared light. A rectangular waveguide, a rectangular waveguide-type coupler, and a power divider based on an origami structure with a multi-layer structure and a single-layer structure were fabricated and tested, demonstrating easy assembly and good microwave performance. The measured results of the rectangular waveguide indicated that the insertion loss was superior to −0.9 dB. Meanwhile, the results of the coupler showed that the coupling degree increased from −12.8 dB to −8.9 dB in the range of 11.0 GHz to 12.0 GHz. Correspondingly, the prepared power divider demonstrated that the return loss dwindled from −8.9 dB to −11.3 dB and that the insertion loss of one output port was approximate to that of the remaining one, varying between −3.5 dB and −5.2 dB in the range of 10.5 GHz to 11.5 GHz—verifying the effectiveness of the origami-based design method. [ABSTRACT FROM AUTHOR]

The contact state of a seamless internal threaded copper tube and an aluminium foil fin not only affects the heat transfer efficiency of a tube–fin heat exchanger but also seriously affects its service life. In this study, hydraulic expansion technology was used to connect the copper tube with an internal thread with a 7 mm diameter to the fin of the heat exchanger. The influence of the expansion pressure and pressure holding time on the contact state was analysed through experiments and finite element simulation, and the variation law of the two on the contact state was obtained. The contact state was characterised by the contact gap and contact area. In order to obtain the specific contact area value, a new method of measuring the contact area was developed to reveal the variation in contact area between the copper tube and the fin after expansion. The results show that the contact gap decreases with an increase in expansion pressure, while the pressure holding time remains the same. The contact area increases with an increase in expansion pressure, and the rate of increase slows. When the expansion pressure is 18 MPa, the average contact gap is approximately 0.018 mm. When the expansion pressure reaches 16 MPa, the contact area ratio is 91.0%. When the expansion pressure increases to 18 MPa, the contact area ratio only increases by approximately 0.6%. Compared with the influence of the expansion pressure on the increase in contact area, the influence of the pressure holding time on the contact area is lower. [ABSTRACT FROM AUTHOR]

A novel annealing process of controlled heating rate is used to produce severe cold-formed aluminum plates, which are processed into aluminum foil and mainly used for high-voltage electrolytic capacitor anodes. The experiment in this study focused on various aspects such as microstructure, recrystallization behavior, grain size, and grain boundary characteristics. The results revealed a comprehensive influence of cold-rolled reduction rate, annealing temperature, and heating rate on recrystallization behavior and grain boundary characteristics during the annealing process. The heating rate applied plays a crucial role in controlling the recrystallization process and the subsequent grain growth, which ultimately determines whether or not the grains will become larger. In addition, as the annealing temperature rises, the recrystallized fraction increases and the grains size decreases; conversely, the recrystallized fraction decreases as the heating rate increases. When the annealing temperature remains constant, the recrystallization fraction increases with a greater deformation degree. Once complete recrystallization occurs, the grain will undergo secondary growth and may even subsequently become coarser. If the deformation degree and annealing temperature remain constant, the increased heating rate will result in a lower recrystallization fraction. This is due to the inhibition of recrystallization, and most of the aluminum sheet even remains in a deformed state before recrystallization. This kind of microstructure evolution, grain characteristic revelation, and recrystallization behavior regulation can provide effective help for enterprise engineers and technicians to guide the production of capacitor aluminum foil to a certain extent, so as to improve the quality of aluminum foil and increase the electric storage performance. [ABSTRACT FROM AUTHOR]

The aim of this study was to investigate the real-world electrical parameters that strongly affected the performance of a triboelectric energy-harvesting floor tile design: triboelectric material thickness, cover plate displacement distance or gap width, and cover plate pressing frequency, so that real-world specifications of the harvesting floor tile can be accurately specified. The structure of the designed triboelectric energy harvester, with readily available polytetrafluoroethylene (PTFE) film and aluminum foil, was simple and hence easy to fabricate, and the material cost was low. A square wave was used to simulate the pressing frequency on the test bench's cover plate. The results showed that the voltage and current were proportional to the gap width, and the thinner the triboelectric layer thickness, the higher the output voltage and current. A test bench with a 0.2 mm thick PTFE triboelectric layer generated the highest energy output. In a later experiment, a triboelectric energy-harvesting floor tile (TEHFT) prototype was constructed with 0.1 and 0.2 mm thick PTFE layers. We found that at 2 Hz stepping frequency and 0.1 mm PTFE thickness, the optimal load and cumulative energy of the TEHFT were 0.8 MΩ and 3.81 mJ, respectively, while with 0.2 mm PTFE thickness, these two parameters were 1.1 MΩ and 7.69 mJ, respectively. The TEHFT with 0.2 mm thick PTFE layer was able to illuminate a series of 100 to 150 LEDs, sufficient power to drive small electronics and sensor nodes. This discovery provides important data on the structure, material, and contact surface area of a TEHFT that can be adjusted to suit specific requirements of a special function triboelectric energy harvester. [ABSTRACT FROM AUTHOR]

An alternative solution to the problem of aluminum–plastic multilayer waste utilization was suggested. The process can be used for hydrogen generation and layer separation. Three different sorts of aluminum–plastic sandwich materials were treated with an alkali solution. In the temperature range of 50–70 °C, for tablet blisters of polyvinylchloride and aluminum (14.8 wt.%), the latter thoroughly reacted in 15–30 min. For sheets of paper, polyethylene, and aluminum (20 wt.%), full hydrogen 'recovery' from reacted aluminum component took 3–8 min. From the lids of polyethylene terephthalate, aluminum (60 wt.%), and painted polyethylene with perforations, the aluminum was consumed after 45–105 min. The effect of perforations was the reduction of the process duration from nearly 90 min for the lids with no perforations to nearly 45 min for the perforated ones (at 70 °C). Perforations provided better contact between the aluminum foil, isolated between the plastic layers, and the alkali solution. Hydrogen bubbles originating near those perforations provided foil separation from the upper painted plastic layer by creating gas gaps between them. The remaining components of the composite multilayer materials were separated and ready for further recycling. [ABSTRACT FROM AUTHOR]

To clarify the microstructure, grain size, and recrystallization behavior during different annealing processes with controlled heating rates, the aim of this study was to investigate the effect of residual deformation energy after cold rolling and critical heating rate on cubic texture components, and grain growth behavior of aluminum plate, which was subjected to severe deformation. The experimental results revealed that the stored energy can be inferred from a calculation that fast annealing (FA) for 30 s was 2.2 times as large as slow annealing (SA) at 320 °C, which provided the driving force for grain growth during subsequent heating and resulted in a significant coarsening of grains in the FA process. In contrast, the intensity of cubic texture in SA was significantly higher than that in the FA process. A critical heating rate of 50 °C/min had been obtained to produce a homogeneous microstructure and strong cubic texture during the annealing processes with controlled heating rates and was verified by experiment. The relationship of Δηsur > 0.02ηb was as a criterion used to determine whether abnormal grain growth happened in aluminum foil, while the grain size exceeded the thickness of aluminum foil by examined calculation. [ABSTRACT FROM AUTHOR]

The influence of tin foil and Ni coatings on microstructures, mechanical properties, and the interfacial reaction mechanism was investigated during laser welding/brazing of Al/Cu lap joints. In the presence of a Zn-based filler, tin foil as well as Ni coating strengthened the Al/Cu joints. The tin foil only slightly influenced the joint strength. It considerably improved the spreading/wetting ability of the weld filler; however, it weakened the bonding between the seam and the Al base metal. The Ni coating considerably strengthened the Al/Cu lap joints; the highest tensile strength was 171 MPa, which was higher by 15.5% than that of a joint without any interlayer. Microstructure analysis revealed that composite layers of Ni3Zn14–(τ2 Zn–Ni–Al ternary phase)–(α-Zn solid solution)–Al3Ni formed at the fusion zone (FZ)/Cu interface. Based on the inferences about the microstructures at the interfaces, thermodynamic results were calculated to analyze the interfacial reaction mechanism. The diffusion of Cu was limited by the Ni coating and the mutual attraction between the Al and Ni atoms. The microstructure comprised Zn, Ni, and Al, and they replaced the brittle Cu–Zn intermetallic compounds, successfully strengthening the bonding of the FZ/Cu interface. [ABSTRACT FROM AUTHOR]

An original technique of chemical deposition (CVD) by catalytic pyrolysis of ethanol vapor was used to directly grow multiwall carbon nanotubes (MWCNTs) layers on aluminum foil. The grown nanotubes had excellent adhesion and direct electrical contact to the aluminum substrate. This material was perfect for use in electrochemical supercapacitors. In this work, the possibility of a significant increase in the specific capacity of MWCNTs by simple electrochemical oxidation was investigated. The optimal conditions for improving the characteristics of the MWCNT/Al electrodes were found. Electrochemical treatment of MWCNT/Al electrodes in a 0.005 M Na2SO4 solution at a potential of 4–5 V for 20–30 min increased the specific capacity of MWCNTs from 30 F/g to 140 F/g. The properties of modified nanotubes were investigated by X-ray photoelectron spectroscopy, cyclic voltammetry (CV), and impedance spectroscopy. A significant increase in the concentration of oxygen-containing functional groups on the surface of MWCNTs was found as a result of electrochemical oxidation. The modified MWCNT/Al electrodes maintained excellent stability to multiple charge–discharge cycles. After 20,000 CVs, the capacity loss was less than 5%. Thus, the results obtained significantly expanded the possibilities of using MWCNT/Al composite materials obtained by the method of direct deposition of carbon nanotubes on aluminum foil as electrodes for supercapacitors. [ABSTRACT FROM AUTHOR]

The shredding of end-of-life refrigerators produces every year in Italy 15,000 tons of waste polyurethane foam (PUF), usually destined for energy recovery. This work presents the results of the investigation of the oil sorption potential of waste PUF according to ASTM F726–17 standard. Three oils (diesel fuel and two commercial motor oils) having different densities (respectively, 0.83, 0.87, and 0.88 kg/dm3) and viscosities (respectively, 3, 95, and 140 mm2/s at 40 °C) were considered. The waste PUF was sampled in an Italian e-waste treatment plant, and its characterization showed 16.5 wt% particles below 0.71 mm and 13 wt% impurities (paper, plastic, aluminum foil), mostly having dimensions (d) above 5 mm. Sieving at 0.071 mm was applied to the waste PUF to obtain a "coarse" (d > 0.71 mm) and a "fine" fraction (d < 0.71 mm). Second sieving at 5 mm allowed an "intermediate" fraction to be obtained, with dimensions between 0.71 and 5 mm. The oil sorption tests involved the three fractions of waste PUF, and their performances were compared with two commercial oil sorbents (sepiolite and OKO-PUR). The results of the tests showed that the "fine" PUF was able to retain 7.1–10.3 g oil/g, the "intermediate" PUF, 4.2–7.4 g oil/g, and the "coarse" PUF, 4.5–7.0 g oil/g, while sepiolite and OKO-PUR performed worse (respectively, 1.3–1.6 and 3.3–5.3 g oil/g). In conclusion, compared with the actual management of waste PUF (100 wt% sent to energy recovery), the amount destined directly to energy recovery could be limited to 13 wt% (i.e., the impurities). The remaining 87 wt% could be diverted to reuse for oil sorption, and afterward directed to energy recovery, considered as a secondary option. [ABSTRACT FROM AUTHOR]

This study investigated the one-pot hydrothermal synthesis of mixed-phase ion-exchangers from waste amber container glass and three different aluminium sources (Si/Al = 2) in 4.5 M NaOH(aq) at 100 °C. Reaction products were characterised by X-ray diffraction analysis, Fourier transform infrared spectroscopy, 27Al and 29Si magic angle spinning nuclear magnetic resonance spectroscopy and scanning electron microscopy at 24, 48 and 150 h. Nitrated forms of cancrinite and sodalite were the predominant products obtained with reagent grade aluminium nitrate (Al(NO3)3∙9H2O). Waste aluminium foil gave rise to sodalite, tobermorite and zeolite Na-P1 as major phases; and the principal products arising from amorphous aluminium hydroxide waste were sodalite, tobermorite and zeolite A. Minor proportions of the hydrogarnet, katoite, and calcite were also present in each sample. In each case, crystallisation was incomplete and products of 52, 65 and 49% crystallinity were obtained at 150 h for the samples prepared with aluminium nitrate (AN-150), aluminium foil (AF-150) and amorphous aluminium hydroxide waste (AH-150), respectively. Batch Pb2+-uptake (~100 mg g−1) was similar for all 150-h samples irrespective of the nature of the aluminium reagent and composition of the product. Batch Cd2+-uptakes of AF-150 (54 mg g−1) and AH-150 (48 mg g−1) were greater than that of AN-150 (36 mg g−1) indicating that the sodalite- and tobermorite-rich products exhibited a superior affinity for Cd2+ ions. The observed Pb2+- and Cd2+-uptake capacities of the mixed-product ion-exchangers compared favourably with those of other inorganic waste-derived sorbents reported in the literature. [ABSTRACT FROM AUTHOR]

Graphite/Al composites have attracted much attrition due to their excellent thermal properties. However, the improvement of thermal conductivity (TC) is limited by the difficulty in controlling the orientation of graphite and the poor wettability between graphite and aluminum. In this study, a novel process for fabricating the Graphite/Al composites is proposed, which involves fabricating graphite film and aluminum foil into laminate material. Then, taking a rolling method, the fractured and well oriented graphite film can help the composite achieve high TC while maintaining a certain strength. The result reveals that both single and total reduction have a significant influence on the diameter and orientation of the graphite, and by adjusting the process parameters, composites with high TC can be acquired at a relatively low reinforcement volume. This near-net-forming process can directly meet the thickness requirements for electronic packaging and avoids the exposure of graphite to the surface during secondary processing, which is promising to promote the application for high TC Graphite/Al composites in thermal management. [ABSTRACT FROM AUTHOR]

Delamination is one of the most common types of defects for carbon fiber reinforced plastic (CFRP) composites. The application of laser techniques to detect delamination faces difficulties with ultrasonic wave excitation because of its low thermal conductivity. Much of the research that can be found in the literature has only focused on the detection of a single delamination. In this study, aluminum foil was pasted onto the surface of the composite so that it was vulnerable to ablation and could acquire a usable signal. Using a fully noncontact system with laser excitation at a fixed point and a scanning laser sensor, the effects of different aluminum foil sizes and shapes on the wavefield were studied for the composites; we decided to use a rectangle with 3 mm length and 5 mm width for laser excitation experiments. Wavefield characteristics of the composite plates were analyzed with single- and multi-layered Teflon inserts. Taking the time window for standard ultrasonic testing as a reference, the algorithms for localized wave energy with appropriate time windows are presented for the detection of single and multiple defects. The appropriate time window is meaningful for identifying each delamination defect. The algorithm performs well in delamination detection of the composites with one or multiple Teflon inserts. [ABSTRACT FROM AUTHOR]

The volumetric growth, composition, and morphology of porous alumina films fabricated by reduced temperature 280 K galvanostatic anodizing of aluminum foil in 0.4, 1.0, and 2.0 M aqueous sulfuric acid with 0.5–10 mA·cm−2 current densities were investigated. It appeared that an increase in the solution concentration from 0.4 to 2 M has no significant effect on the anodizing rate, but leads to an increase in the porous alumina film growth. The volumetric growth coefficient increases from 1.26 to 1.67 with increasing current density from 0.5 to 10 mA·cm−2 and decreases with increasing solution concentration from 0.4 to 2.0 M. In addition, in the anodized samples, metallic aluminum phases are identified, and a tendency towards a decrease in the aluminum content with an increase in solution concentration is observed. Anodizing at 0.5 mA·cm−2 in 2.0 M sulfuric acid leads to formation of a non-typical nanostructured porous alumina film, consisting of ordered hemispheres containing radially diverging pores. [ABSTRACT FROM AUTHOR]

The Al–Li alloy is becoming popular for aerospace application owing to their low density, high specific strength, good corrosion resistance, etc. The diffusion bonding/superplastic forming (DB/SPF) structure of titanium alloy has been widely used in the aerospace industry. In order to broaden the application of Al–Li alloy, it is necessary to develop its diffusion bonding and superplastic forming (DB/SPF) technology. In the present study, diffusion bonding of 1420 Al–Li alloy assisted by pure aluminum foil was conducted on Gleeble-3500 thermal simulation system under different bonding parameters, the results show that the bonding temperatures have direct influence on the interface microstructure and bond strength of joints. Meanwhile, when the pure aluminum interlayer was introduced into the diffusion bonding process, the alloying element diffusion across the bond can improve the interface integrity and the mechanical properties. The joint formation mechanism with interlayer was investigated in detail, the development and application of this method was explored. [ABSTRACT FROM AUTHOR]

Higher efficiency and output power of a photovoltaic (PV) module can be achieved by minimizing cell-to-module (CTM) power losses. CTM losses are mainly dependent on electrical and optical losses. In this work, reflection losses from interspacing of cells with respect to different encapsulant materials and backsheets are evaluated. Two novel encapsulant materials thermoplastic polyolefin (TPO) and polybutadiene ionomer are used, in addition to conventionally used ethylene vinyl acetate (EVA). Moreover, the effect of using these encapsulant materials separately with Tedlar and Aluminum foil as backsheets is realized. It has been observed that TPO in combination with Tedlar presents minimum reflection losses compared to other encapsulant materials. The reflection losses calculated experimentally with polybutadiene ionomer were 5.4% less than the conventionally used EVA, whereas, the reflection losses calculated experimentally with TPO were 5.9% less than the conventionally used EVA. The experimental results obtained are also validated through simulations. [ABSTRACT FROM AUTHOR]

This work proposes a micro-shear clinching process by laser shock for joining similar and dissimilar metal foils. The joint appearance and cross-section were investigated to determine basic process parameters. The soft punch thickness was 100 μm. The numbers of laser pulses on the upper and lower foil sides were set as two and one, respectively. Joint deformation was divided into three stages and we investigated the deformation law of the joints. The process windows of the Al foil combinations were acquired to determine a reasonable range of process parameters for obtaining qualified joints. The mechanical properties and failure modes of different joints were analyzed to identify the process characteristics. Mechanical properties were related to shear test directions and were influenced by upper and lower foil thicknesses. One failure mode was observed in the parallel shear test, and four failure modes were observed in the perpendicular shear test. These modes were determined by the differences between upper and lower foil thicknesses. Results showed that the proposed process can be used to join Al and Cu foils successfully. The laws governing the mechanical properties and failure modes of dissimilar materials were similar to those governing the mechanical properties and failure modes of similar materials. [ABSTRACT FROM AUTHOR]