Search

Our research group prepared a new filling paste consisting of steel slag–oil shale residue and no admixtures. It was used as the research object to explore the combined effect of chloride and dry–wet cycling-driven erosion on the long-term stability of a cemented filling paste made of total solid wastes. Macroscopic experiments and microscopic analyses methods were employed. The influence of solutions with different mass fractions of chloride salts and different cycling periods on the uniaxial compressive strength and toxicity of the steel slag–oil shale residue-based filling paste was studied, and the deterioration mechanisms of the steel slag–oil shale residue-based filling paste under combined erosion from chloride and dry–wet cycling were investigated. The test results showed that in the same cycling conditions, the strength of the steel slag-oil shale residue-based filling paste increased first with the increase in the mass fraction of the chloride solution and then decreased with the increase in the mass fraction of the chloride solution after reaching the peak value; the leached concentrations of heavy metal ions decreased with increasing chloride salt mass fraction. With an increase in the number of dry–wet cycles, the compressive strength of the specimens in the chloride salt solution with a mass fraction of 0 (pure water) first increases and then tends to be stable. The strength of samples in 5% and 10% chloride salt solutions increased first and then decreased with an increase in the number of dry–wet cycles. The leached concentrations of heavy metal ions from the samples in all three solutions first decreased and then stabilized. The prehydration products of the steel slag–oil shale residue-based filling paste were C-S-H gels, AFt and Friedel's salt, and these increased with increasing chloride salt mass fraction and the number of dry–wet cycles. However, the hydration reactions of the samples in the 0% chloride solution nearly stopped in the later stages of cycling, and the samples in 5% and 10% chloride salt solutions developed local cracks due to the accumulation of hydration products. The results showed that the number of dry–wet cycles and the chloride salt mass fraction affected the strength and leaching characteristics of the steel slag–oil shale residue-based filling paste by changing the type and amount of erosion products. The test results provide a scientific basis for the promotion and application of backfilling pastes made from total solid wastes. [ABSTRACT FROM AUTHOR]

Previous studies have shown that the effectiveness of superfine tailings cemented paste backfill (SCPB) is influenced by multiple factors. To optimize the filling effect of superfine tailings, the effects of different factors on the fluidity, mechanical properties, and microstructure of SCPB were investigated. Before configuring the SCPB, the effect of cyclone operating parameters on the concentration and yield of superfine tailings was first investigated and the optimal cyclone operating parameters were obtained. The settling characteristics of superfine tailings under the optimum cyclone parameters were further analyzed, and the effect of the flocculant on its settling characteristics was shown in the block selection. Then the SCPB was prepared using cement and superfine tailings, and a series of experiments were carried out to investigate its working characteristics. The flow test results showed that the slump and slump flow of SCPB slurry decreased with increasing mass concentration, which was mainly because the higher the mass concentration, the higher the viscosity and yield stress of the slurry, and thus the worse its fluidity. The strength test results showed that the strength of SCPB was mainly affected by the curing temperature, curing time, mass concentration, and cement-sand ratio, among which the curing temperature had the most significant effect on the strength. The microscopic analysis of the block selection showed the mechanism of the effect of the curing temperature on the strength of SCPB, i.e., the curing temperature mainly affected the strength of SCPB by affecting the hydration reaction rate of SCPB. The slow hydration process of SCPB in a low temperature environment leads to fewer hydration products and a loose structure, which is the fundamental reason for the strength reduction of SCPB. The results of the study have some guiding significance for the efficient application of SCPB in alpine mines. [ABSTRACT FROM AUTHOR]

Unconfined compressive strength (UCS) is the most significant mechanical index for cemented backfill, and it is mainly determined by traditional mechanical tests. This study optimized the extreme gradient boosting (XGBoost) model by utilizing the whale optimization algorithm (WOA) to construct a hybrid model for the UCS prediction of cemented backfill. The PT proportion, the OPC proportion, the FA proportion, the solid concentration, and the curing age were selected as input variables, and the UCS of the cemented PT backfill was selected as the output variable. The original XGBoost model, the XGBoost model optimized by particle swarm optimization (PSO-XGBoost), and the decision tree (DT) model were also constructed for comparison with the WOA-XGBoost model. The results showed that the values of the root mean square error (RMSE), coefficient of determination (R2), and mean absolute error (MAE) obtained from the WOA-XGBoost model, XGBoost model, PSO-XGBoost model, and DT model were equal to (0.241, 0.967, 0.184), (0.426, 0.917, 0.336), (0.316, 0.943, 0.258), and (0.464, 0.852, 0.357), respectively. The results show that the proposed WOA-XGBoost has better prediction accuracy than the other machine learning models, confirming the ability of the WOA to enhance XGBoost in cemented PT backfill strength prediction. The WOA-XGBoost model could be a fast and accurate method for the UCS prediction of cemented PT backfill. [ABSTRACT FROM AUTHOR]

Cemented paste backfill (CPB), a technology placing the solid waste into mined-out stopes in the mine through pipeline transportation, has been widespread all over the world. The resistance loss is an important parameter for pipeline transport, which is significantly affected by the slurry characteristics. However, the coupling effect of inlet velocity (IV), particle mass concentration (PMC), and particle size (PS) has not been well evaluated and diagnosed. Hence, the CFD-based three-dimensional network simulation of CPB slurry flow in an L-shaped pipe at different combinations of the three parameters was developed using COMSOL Multiphysics software, and the findings were validated through a loop experiment. The results show that increasing IV and reducing PS will contribute to the homogeneity of the slurry in the pipeline, while the PMC presents little effect. The pipe resistance loss is positively correlated with IV and PMC and negatively correlated with PS. The sensitivity to the three parameters is IV > PS > PMC. In particular, the resistance loss is minimal at IV of 1.5 m/s, PMC of 72%, and PS of 1000 um. The calculation model of resistance loss regressed from simulation presented a high accuracy with an error of 8.1% compared with the test results. The findings would be important for the design of the CPB pipeline transportation and provide guidance in the selection of transfer slurry pumps, prepreparation of backfill slurry, and pipe blockage, which will improve the safety and economic level of a mine. [ABSTRACT FROM AUTHOR]

Cemented paste backfill (CPB) has become a significant structural material in most mines across the world. In this study, the effects of chemical rheological additives including viscosity modifying agent (i.e., polyacrylamide) and polycarboxylate superplasticizer (PCE) on fresh and hardened properties of CPB with different water-to-solid (W/S) ratios and water-to-cement (W/C) ratios were investigated. The microstructure of CPB specimens was also characterized by X-ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and backscattered electron image (SEM-BSE). The obtained results indicate that PAM (polyacrylamide) dosage and W/S are the most significant parameters influencing the workability of fresh CPB mixtures. For the hardened CPB specimens, the decreasing W/S ratio leads to higher flexural and compressive strength values and lower dry shrinkage strains. The interfacial transition zone (ITZ) between the cement matrix and the tailings sand was also observed to be narrower, with fewer micro cracks and capillary pores. Meanwhile, the existence of PAM decreased the number of hydration products and retarded the hydration reaction. Overall, the CPBs with high W/C ratios (i.e., 1.0 and 1.2), low W/S ratios (i.e., 0.3), and moderate amounts of rheological additives (i.e., 0.05% PAM and 1.0% PCE) have excellent fresh and hardened properties. The findings of this study contribute to better optimization of CPB mixtures in backfill construction, bringing benefits of low costs and low environmental impacts. [ABSTRACT FROM AUTHOR]

A new type of cemented paste backfill (CPB) was prepared using sodium hydroxide (NaOH) as the activator, slag and silica fume (SF) as the binder, and tailings as the aggregate. The effects of proportion of replacement of 0%, 5%, 10%, 15%, and 20% silica fume on the properties of CPB were studied. The strength formation mechanism of CPB was explored through a combination of scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), and Fourier transform infrared (FTIR) spectroscopy. The SEM images were analyzed by IMAGE J software, and the porosity of CPB with different silica fume contents was obtained. The results show that as the amount of silica fume increases, the unconfined compressive strength (UCS) increases first and then decreases. When the amount of silica fume was approximately 5%, CPB with a larger UCS can be obtained. When the silica fume content increased from 0% to 5%, because silica fume has good activity and small particles, more calcium silicate hydrate (C–S–H) gels and Mg-Al type layered double hydrotalcites (LDHs) were generated in CPB, which made it denser and improved its strength compared with the non-silica fume group. C–S–H gels were the main source of CPB strength. With a further increase in the amount of silica fume, thaumasite produced inside of CPB, reducing the content of C–S–H gels. Moreover, due to the expansion of thaumasite, it is easy to generate a large number of micro cracks in CPB, which weakens the strength of CPB. [ABSTRACT FROM AUTHOR]

This study examines the combined performance of Portland cement (PC), the binder, and fly ash (FA), the additive, towards improving the mechanical performance of the South Australian copper-gold underground mine cemented paste backfill (CPB) system. A series of unconfined compressive strength (UCS) tests were carried out on various mix designs to evaluate the effects of binder and/or additive contents, as well as curing time, on the CPB's strength, stiffness and toughness. Moreover, the failure patterns of the tested samples were investigated by means of the three-dimensional digital image correlation (DIC) technique. Making use of several virtual extensometers, the state of axial and lateral strain localization was also investigated in the pre- and post-peak regimes. The greater the PC content and/or the longer the curing period, the higher the developed strength, stiffness and toughness. The use of FA alongside PC led to further strength and stiffness improvements by way of inducing secondary pozzolanic reactions. Common strength criteria for CPBs were considered to assess the applicability of the tested mix designs; with regards to stope stability, 4% PC + 3% FA was found to satisfy the minimum 700 kPa threshold, and thus was deemed as the optimum choice. As opposed to external measurement devices, the DIC technique was found to provide strain measurements free from bedding errors. The developed field of axial and lateral strains indicated that strain localization initiates in the pre-peak regime at around 80% of the UCS. The greater the PC (or PC + FA) content, and more importantly the longer the curing period, the closer the axial stress level required to initiate localization to the UCS, thus emulating the failure mechanism of quasi-brittle materials such as rock and concrete. Finally, with an increase in curing time, the difference between strain values at the localized and non-localized zones became less significant in the pre-peak regime and more pronounced in the post-peak regime. [ABSTRACT FROM AUTHOR]