Search

Dual-material lattices with tailorable coefficients of thermal expansion have been applied to a wide range of modern engineering systems. As supporting techniques for fabricating dual-material lattices with given coefficients of thermal expansion, the current existing methods for measuring the coefficient of thermal expansion have limited anti-interference ability. They ignore the measuring error caused by micro-displacement between the measurement sensor and the test sample. In this paper, we report a robust interferometric test method which can eliminate the measurement error caused by micro-displacement between the measurement sensor and the test sample. In the presented method, two parallel plane lenses are utilized to avoid the measurement error caused by translation, and the right lens is utilized as an angle detector to eliminate the measurement error caused by rotation. A robust interferometric testing setup was established using a distance measuring set and two plane lenses. The experiment results indicated that the method can avoid the measurement error induced by translation and has the potential to eliminate the measurement error induced by rotation using the rotational angle. This method can improve the anti-interference ability and accuracy by eliminating the measurement error. It is especially useful for high-precision thermal expansion measurement of dual-material lattices. [ABSTRACT FROM AUTHOR]

Negative thermal expansion (NTE) lattices are widely used in aerospace engineering where the structures experience large temperature variation. However, the available range of NTE of the current lattices is quite narrow, which severely limits their engineering application. In this paper, we report an inverted trapezoid lattice (ITL) with large NTE. The NTE of the ITL is 2.6 times that of a typical triangular lattice with the same height and hypotenuse angle. Theoretically, with a pin-jointed assumption, the ITL can improve the NTE by order of magnitude if the length ratio of the composite rod is changed. In the presented ITL, a composite rod is utilized as the base of the ITL. The composite rod has large inner NTE. The inverted trapezoid structure converts the inner NTE to the vertical direction contraction and obtains an extra NTE. Finite element simulations and experimental verification by interferometric measurement were conducted to verify the large thermal expansion of the ITL. [ABSTRACT FROM AUTHOR]

An accurate equivalent method of metal joint interface is of great significance to optimize the dynamic performance of the whole machine. Therefore, it is necessary to establish an accurate equivalent method of joint interface. The virtual material method is a precise equivalent method of joint interface. The traditional virtual material method is based on the M–B fractal contact theory. By modeling the contact mechanics of the joint interface, the physical properties of the virtual material are obtained separately, such as elastic modulus, Poisson's ratio and density. In this paper, Persson contact theory is used to establish the interface contact mechanics model to find the physical properties of virtual materials. The virtual material methods constructed by two theories are respectively applied to the modal simulation to obtain the natural frequencies of the joint interface. By comparing the natural frequencies obtained by modal experiment and modal simulation, it is found that the natural frequencies obtained by the virtual material method based on Persson contact theory are closer to the results obtained by the modal experiment, and the error is within 5%. The error of the natural frequencies obtained by the virtual material method based on the M–B fractal contact theory is within 10%. Therefore, the Persson contact theory can establish a more accurate equivalent method of metal's joint interface. [ABSTRACT FROM AUTHOR]

Modal performance of a bolted structure is important when considering a precise mechanical product. Joint interface is a critical aspect of a bolted structure, which is difficult to analyze because of its rough profiles. Equivalent material (EM) is used to simplify the joint interface, which reduces the computational cost and modeling difficulty. Using a modified fractal model based on an oblique asperity contact, we calculated the elastic modulus, the shear modulus, the Poisson's ratio, and the density of EM. The finite element method was applied to discriminate between the resonant frequencies of bolted structures with EM and without EM. The simulation results are compared with the classical frequency response experiment. The errors between experiments and the bolted structures with EM are less than 10%, which are much less than those without EM. It can be concluded that bolted structures with EM are more reliable and reasonable. Furthermore, the effect of EM is more obvious when the joint interface has a small size, roughness, and tightening torque. [ABSTRACT FROM AUTHOR]

In order to effectively improve the dynamic characteristics of the fixed metal joint interface, it is important to establish a correct equivalent model of the metal joint interface. In this paper, three equivalent methods for simulating the metal joint interface are analyzed, including the virtual material method, spring damping method, finite element method, and verification by modal experiment. First, according to the contact mechanics model of the constructed metal joint interface, the physical properties of the three-dimensional models of the fixed joint interface are assigned in the ANSYS software. Then, three methods are used for the modal analysis and compared with a modal experiment. The results show that the modal shapes of the three theoretical methods are consistent with those of the experimental modes. The first five natural frequencies obtained by the virtual material method are closest to the experimental natural frequencies, and the errors are within 10%. The errors of the other two methods are between 9% and 39%. Therefore, the virtual material method is a better equivalent method of the metal joint interface. [ABSTRACT FROM AUTHOR]

In this paper, we present a periodic hollowed-out pyramid microstructure with excellent superhydrophobicity. In our approach, T-topping pillars and capillary-induced self-assembly methods were combined with the photolithography process to fabricate a hollowed-out pyramid structure. First, a wideband ultraviolet source without a filter was used to fabricate the T-topping pillars during the exposure process; then, the evaporation-induced assembly collapsed the pillars and formed the hollowed-out pyramid structure. Scanning electron microscopy images showed the microstructures of the prepared surface. The contact angle of the surface was 154°. The surface showed excellent high temperature and ultraviolet irradiation tolerance, and the contact angle of the surface barely changed when the temperature dropped. This excellent environmental durability of our superhydrophobic surface has potential applications for self-cleaning and friction drag reduction under water. [ABSTRACT FROM AUTHOR]