Search

With rapid infrastructure development worldwide, the generation of industrial solid waste (ISW) has substantially increased, causing resource wastage and environmental pollution. Meanwhile, tunnel engineering requires large quantities of grouting material for ground treatment and consolidation. Using ISW as a component in tunnel grouts provides a sustainable solution to both issues. This paper presented a comprehensive review of the recent advancements in tunnel grouting materials using ISW, focusing on their feasibility, mechanical characteristics, and future development directions. Initially, the concept and classification of ISW were introduced, examining its feasibility and advantages as grouting materials in tunnels. Subsequently, various performances of ISW in tunnel grouting materials were summarized to explore the factors influencing mechanical strength, fluidity, durability, and microstructure characteristics. Simultaneously, this review analyzed current research trends and outlines future development directions. Major challenges, including quality assurance, environmental risks, and lack of standardized specifications, are discussed. Future research directions, including multifunctional grouts, integrated waste utilization, and advanced characterization techniques, are suggested to further advance this field. These findings provided useful insights for the continued development of high-performance and environmentally friendly ISW-based grouting materials. [ABSTRACT FROM AUTHOR]

The effect of hot working parameters on the microstructure and texture evolution of the hot-deformed Zr-45Ti-5Al-3V alloy was studied by the electron backscatter diffraction (EBSD) technique. It was found that a high density of dislocations were generated when the alloy was deformed at 700 °C/0.001 s−1 and 800 °C/1 s−1. With the increment in hot-deformation temperature and the decrease in strain rate, the dislocation density decreased due to the increase in dynamic recrystallization (DRX) degree. The discontinuous dynamic recrystallization (DDRX) and continuous dynamic recrystallization (CDRX) mechanisms co-existed during the hot working of the Zr-45Ti-5Al-3V alloy at a true strain of 0.7. The texture evolution of the alloy during hot working was characterized and the texture component mainly consisted of {001}<100>, {011}<100>, {110}<112>, and {112}<110> textures. The volume fractions of {001}<100> and {011}<100> textures obviously rose with the reduction in strain rate, whereas those of {110}<112> and {112}<110> textures gradually decreased. At a given strain rate, an increase trend in the volume fraction of the {001}<100> texture was observed with rising hot-deformation temperature, while the volume fraction of the {011}<100> texture first increased and then decreased. An opposite trend was visible in the {112}<110> and {110}<112> texture compared with {011}<100> textures. [ABSTRACT FROM AUTHOR]

Luffa is a lightweight porous material with excellent biocompatibility and abundant resources. In this paper, three kinds of softening treatment methods, alkali-hydrogen peroxide (Method 1), alkali-acetic acid (Method 2), and alkali-urea (Method 3), were used to soften high-density (HD) cylindrical luffa (CL) mattress-filling materials (MFM). Microscopic observation, mechanical performance testing and other analyses were performed to evaluate the effects of the three kinds of softening methods on the wettability, compression resilience and support performance of CL MFM. The results showed that: (1) After the treatment by Method 1, Method 2 and Method 3, the peak stress of CL decreased by 73%, 10% and 27%, respectively. In addition, after three kinds of softening treatments, the uniformity of CL increased. (2) When the CL MFM of high density rank treated by Method 1 was compressed by 40%, the firmness values of the surface, core and bottom reduced by 53.49% 40.72%, and 46.17%, respectively, compared to that of untreated CL. In addition, for the CL MFM of high density rank treated by Method 3 and then compressed to 60%, the firmness of the surface layer, core layer and bottom layer reduced by 41.2%, 33.7%, and 36.9%, respectively. (3) The contact angle of luffa treated by Method 3 was the smallest, next came Method 1 and Method 2, and untreated was the largest. (4) After the treatment by Method 3, the fiber bundle of luffa was intact, and the compression resilience of the CL was obviously increased. Therefore, this method can effectively reduce the firmness of MFM and also improve the uniformity and wettability of CL. [ABSTRACT FROM AUTHOR]

DNA nanostructures, owing to their controllable and adaptable nature, have been considered as highly attractive nanoplatforms for biomedical applications in recent years. However, their use in the biological environment has been restricted by low cellular transfection efficiency in mammalian cells, weak stability under physiological conditions, and endonuclease degradation. Herein, we demonstrate an effective approach to facilitate fast transfection of DNA nanostructures and enhance their stability by encapsulating DNA origami with a biocompatible cationic protein (cHSA) via electrostatic interaction. The coated DNA origami is found to be stable under physiological conditions. Moreover, the cHSA coating could significantly improve the cellular transfection efficiency of DNA origami, which is essential for biological applications. [ABSTRACT FROM AUTHOR]

Luffa sponge (LS) is a resourceful material with fibro-vascular reticulated structure and extremely high porosity, which make it a potential candidate for manufacturing light mattress. In this study, two types of LS columns, namely high-density (HD) and low-density (LD) columns, were investigated as materials for filling the mattress. The results showed that the compressive strength of HD LS columns was significantly greater than that of LD LS columns. However, the densification strains of the two types of LS column were both in the range of 0.6 to 0.7. Besides, HD LS columns separately pressed to the smooth plateau region and the initial densification region exhibited a partial recovery of instant height when they were unloaded, and then both of them showed no more than 4.2% of height recovery after being allowed to rest at a constant temperature and humidity for 24 h. In contrast, when LD LS columns were compressed to the smooth plateau region, the height recovery was less than 1.62% compared to when they were pressed to the initial densification region, and that was more than 15.62%. Similar to other plant fibers used as mattress fillers, the two types of LS columns also showed good water absorption capacity—both of them could absorb water from as much as 2.07 to 3.45 times their own weight. At the same time, the two types of LS columns also showed good water desorption. The water desorption ratio of HD and LD LS columns separately reached 76.86 and 91.44%, respectively, after being let rest at a constant temperature and humidity for 13 h. [ABSTRACT FROM AUTHOR]