Search

This study considers 12 pervious concrete mixes incorporating 100% recycled coarse aggregate from old concrete demolition waste and containing various amounts of natural fine aggregate and date palm leaves fibers. First, the properties of the recycled aggregate in terms of their particle size distribution, abrasion resistance, crushing values, specific gravity and water absorption are obtained. Next, the pervious concrete density, compressive strength, tensile strength, permeability and porosity are determined by experimental testing following the relevant standards. The results are analyzed and compared to determine the influence of using recycled coarse aggregate in the mixtures and the impact of the amount of natural sand and volume fraction of the fibers on the mechanical properties, permeability and porosity of the concrete. Findings of the study showed that the use of recycled coarse aggregate in pervious concrete without fine aggregate reduced the compressive strength by 36% and tensile strength by 57%. Replacing 11.7% of the recycled coarse aggregate with natural sand and adding date palm leaves fibers in an amount equivalent to 0.64% volumetric content to such concrete helped increase the compressive strength by 16.2% and tensile strength by 3.2% above the corresponding strengths of the control mix. There is a clear relationship between permeability and porosity due to their correlation with the density of pervious concrete, and the effect of porosity on tensile strength is more influential than it is on the compressive strength. An equation that can predict the tensile strength of pervious concrete from the compressive strength is proposed, as a function of the natural fine aggregate fraction of the coarse aggregate and volumetric content of natural fibers. Results of the research confirm the feasibility of using recycled aggregate in pervious concrete mixes and the positive impact of natural fibers on the mechanical properties. [ABSTRACT FROM AUTHOR]

The research presented in this article was conducted to evaluate the suitability of recycled foam concrete (RFC) as an ingredient in newly created cement mortars. The basis for an analysis was the assumption that the waste is collected selectively after separation from other waste generated during demolition. The motivation for the research and its main problem is a comparison of the performance of RFC used in various forms. RFC was used in two forms: (1) recycled foam concrete dust (RFCD) as a 25 and 50% replacement of cement, and (2) recycled foam concrete fine aggregate (RFCA) as a 10, 20, and 30% replacement of sand. The basic properties of fresh and hardened mortars were determined: consistency, density, initial setting time, absorbability, compressive strength, thermal conductivity coefficient, and heat capacity. Research is complemented with SEM observations. The properties of fresh mortars and mechanical parameters were decreased with the usage of any dosage of RFC in any form, but the thermal properties were improved. The required superplasticizer amount for proper consistency was raised four times for replacing cement with 50% of RFCD than for 25% of such replacement. The mix density dropped by about 8% and 9% for mortars with the replacement of 50% cement by RFCD and 30% sand by RFCA in comparison to reference mortar. A 30% decrease in initial setting time was observed for cement replacement. In the case of sand replacement, it was the opposite—an increase of 100%. The dry density decreased by about 14% and 11% for mortars with the replacement of 50% cement by RFCD and 30% sand by RFCA in comparison to reference mortar. Absorbability was raised by about two times after replacement with both RFCD and RFCA. Compressive strength after 28 days dropped significantly by 75% and 60%, and the thermal conductivity coefficient decreased by 20% and 50% with 50% RFCD added instead of cement and 30% RFCA replacing sand. It indicates greater efficiency in thermomechanical means from RFCA in comparison to RFCD. This material can be used especially in the production of plaster and masonry mortar. Linear correlations of dry density and thermal conductivity coefficient and the latter and compressive strength were proven as reliable for RFCD replacement of cement and RFCA replacement of sand in mortars with greater w/c ratio. [ABSTRACT FROM AUTHOR]

The proper reutilization of the phosphogypsum (PG) by-product derived from the production of phosphoric acid and recycled concrete aggregate (RCA) from waste concrete in roadbase materials is of great necessity and importance. This investigation tried seeking a new approach to reuse them to high quality, including turning PG into calcinated PG (CPG) via washing and calcination, as well as adopting sodium metasilicate nonahydrate (SMN) to strengthen the roadbase materials of cement-stabilized CPG and RCA. Upon the mix design, with a series of experiments including unconfined compressive strength, the wet–dry cycle, freeze–thaw cycle, and scanning electron microscopy, the comprehensive effects of PG treatment, the CPG to RCA mix ratio, SMN dosage, wet–dry cycle and freeze–thaw cycle on the road performance of roadbase materials were well evaluated, and the traffic bearing capacity and microstructure characteristics were also analyzed. The results demonstrate that the 7 d unconfined compressive strength of CPG/RCA roadbase materials can reach 5.34 MPa as the CPG and SMN dosage are 20% and 11%, respectively, which meets the requirements of an extremely and very heavy traffic grade. After five wet–dry cycles and freeze–thaw cycles, the resistance of the CPG/RCA roadbase materials to moisture and frost was significantly improved as 11% SMN was added. Meanwhile, SMN contributes to the reduction in crack width and densifies the microstructure of CPG/RCA roadbase materials. The research results can be used to provide new guidance for building more durable roadbase materials. [ABSTRACT FROM AUTHOR]

The literature confirms that fine recycled concrete aggregate (fRCA) can be used as a replacement for natural soil in new concrete, offering many advantages. Despite these advantages, there are also critical barriers to the development of fRCA in new mixes. Among these, the first challenge is the variability of fRCA properties, in both physical, chemical, and mechanical terms. Many individual studies have been carried out on different RCA or fRCA properties, but little investigative work has been performed to analyze their dynamic properties. Therefore, the influence of the non-cohesive fine fraction content of RCA on the dynamic properties of this waste material, when used as a specific anthropogenic soil, has been studied in laboratory conditions, employing a standard resonant column apparatus, as well as piezoelectric elements. In the present research, special emphasis has been placed on the dynamic shear modulus, dynamic damping ratio, small-strain shear modulus, and small-strain damping ratio, as well as shear modulus degradation G(γ)/Gmax, the damping ratio increase D(γ)/Dmin, and the threshold shear strain amplitudes γtl and γtv. Artificially prepared fRCAs with varying fine fraction contents (0% ≤ FF ≤ 30%, within increments of 5%) have been tested at different pressures (p′ = 90, 180, and 270 kPa) and relative densities of Dr > 65%. This study also examined the effect of two tamping-based sample preparation methods, i.e., dry and wet tamping. The results presented herein indicate that the analyzed anthropogenic material, although derived from concrete and produced by human activities, behaves very similarly to natural aggregate when subjected to dynamic loading. The introduction of a fine fraction content to fRCA leads to changes in the dynamic properties of the tested mixture. Concrete material with lower stiffness but, at the same time, with stronger damping properties can be obtained. A fine fraction content of at least 30% is sufficient to cause a significant loss of stiffness and, at the same time, a significant increase in the damping properties of the mixture. This study can serve as a reference for designing fRCA mixtures in engineering applications. [ABSTRACT FROM AUTHOR]

The paper presents the results of tests on concrete with recycled aggregate impregnated with the use of citric acid. Impregnation was carried out in two stages, with a suspension of calcium hydroxide in water (so-called milk of lime) or diluted water glass used as the second impregnant. The mechanical properties of the concrete were carried out: compressive strength, tensile strength and resistance to cyclic freezing. In addition, concrete durability parameters such as water absorption, sorptivity and torrent air permeability were investigated. The tests showed that this type of impregnation did not improve most of the parameters of concrete with impregnated recycled aggregate. The mechanical parameters after 28 days were significantly lower compared to the reference concrete, although after a longer curing period, these differences decreased significantly for some series. The durability parameters of the concrete with impregnated recycled aggregate also deteriorated compared to the reference concrete with the exception of air permeability. The results of the tests carried out indicate that impregnation using water glass in combination with citric acid gives the best results in most cases and that the order in which the impregnation solutions are applied is very important. Tests also showed that the effectiveness of impregnation is very much influenced by the value of the w/c ratio. [ABSTRACT FROM AUTHOR]

The decrease in the quality of recycled aggregate due to an increase in the number of recycling is a primary factor that limits the multi-recycling of concrete. This degradation adversely affects concrete performance; thus, the characteristics of recycled aggregate should be considered during the mix design stage, but little research has taken that into account. This study investigates the effect of the equivalent mortar volume (EMV) mix design on some physical, mechanical and durability properties of concrete made of multiple recycled coarse aggregates at 50% and 100% replacement ratios compared to concrete made by the conventional mix design (CMD). The results showed that the performances of concrete by the CMD decreased with an increasing number of recycling cycles. The properties of EMV-based concrete deteriorated with an increase in the number of recycling cycles at 100% replacement ratio due to poor workability caused by a shortage of fresh mortar. However, at 50% replacement, the EMV-based concrete exhibited similar performance across the three cycles of recycling, as well as improved properties over natural aggregate concrete. This study demonstrated that an appropriate mix design and optimal aggregate replacement ratio can offset the property loss of multiple recycled aggregate concrete. [ABSTRACT FROM AUTHOR]

In the case of concrete sustainability, two main ways are generally discussed: (1) the reduction of natural raw materials and (2) the reduction of emissions related to concrete production. Following the second point, there have not yet been reported clear results. This problem is not given enough attention in present publications. This study brings a general view of this issue and a basic comparison with common concrete and traditional reinforcement. This case study deals with the life cycle analysis of a concrete slab made of recycled aggregate concrete with a fine recycled aggregate. The concrete slab was designed according to the limit states of load-bearing capacity and serviceability, which is based on the experimental verification of recycled aggregate concrete properties. Two different reinforcements are compared: (1) ordinary reinforcement by steel bars and (2) glass fibers. Furthermore, scenarios vary due to the slab thickness and reinforcement percentage. The results show the positive environmental impact of replacing natural sand with a fine recycled aggregate. The reduction of climate change potential can be almost 40% in some cases. [ABSTRACT FROM AUTHOR]

The effect of fine and ultrafine recycled concrete aggregate (RCA) on road construction still lacks investigation. This study investigates the properties of fine and ultrafine RCA, further, the influence of the different proportions of ultrafine RCA on the long-term performance of the designed matrix. The fine and ultrafine RCA are thoroughly characterized. Simultaneously, the mechanical properties, shrinkage properties, and water penetration of the designed matrix are evaluated. The results indicate that RCA shows low density, high porosity, and high water absorption. Furthermore, elevated ultrafine RCA contents result in higher compressive strength of up to 43.14% at 90 days and higher resistance of water penetration of up to 50% at 28 days due to the refined microstructure. However, higher drying shrinkage is observed with higher ultrafine RCA, which is associated with the high water absorption of the ultrafine RCA. The understanding of the utilization of ultrafine RCA in the construction of road base courses has been explored. [ABSTRACT FROM AUTHOR]

The main goal and novelty of this study is to show the transferability of practices and experiences with the use of reclaimed sand worldwide in the case in two different regions, the Czech Republic and India, which is necessary for both regions due to the sand availability (Czech Republic) and illegal sand mining including criminal offences (India). Due to the deteriorating environmental impacts associated with sand mining, finding substitution possibilities for natural sand is becoming more important worldwide. It is realized that the reuse of construction demolition waste concrete is inevitable in the pursuit of circular concrete and cleaner production, envisioned by the United Nations (UN) as the attainment of ensuring sustainable consumption and production patterns (Sustainable Development Goal 12-SDG 12) with an inclusive approach of partnerships to achieve the goal (Sustainable Development Goal 17-SDG 17) for the validation of results. The basic material properties of reclaimed sand were examined, and its impact on the physical, mechanical, and durability properties of concrete with complete replacement of sand was evaluated. Generally, a slight decline in properties of concrete with fine recycled aggregate was found. No significant decrease was found from usage possibility in the point of view of its utilization in specific structures and conditions. The research shows the slight differences of results between the Czech and Indian investigations, which are not essential for the transferability of the results. [ABSTRACT FROM AUTHOR]

This study investigates the effects of two waste materials from construction and industry, namely recycled concrete aggregate (RCA) and Type C fly ash, on the overall performance of a special type of pavement surface mixture, porous asphalt mixture. Mixtures of different combinations of RCA (for partial aggregate replacement) and fly ash (for filler replacement) were prepared in the laboratory and tested for a variety of pavement surface performance parameters, including air-void content, permeability, Marshall stability, indirect tensile strength, moisture susceptibility, Cantabro loss, macrotexture, and sound absorption. The analysis of the results showed that incorporating RCA or fly ash in a porous asphalt mixture slightly reduced the air-void content, permeability, and surface macrotexture of the mixture. A 10% replacement of granite aggregates with RCA in the porous asphalt mixtures led to a reduction in mixture stability, indirect tensile strength, resistance to raveling, and sound absorption. The further substitution of mineral filler with fly ash in the mixture, however, helped to offset the negative impact of RCA and brought the mechanical properties of the mixture with 10% RCA to levels comparable to those of the control mixture. [ABSTRACT FROM AUTHOR]

Numerous tests are used to determine the performance of concrete, but compressive strength (CS) is usually regarded as the most important. The recycled aggregate concrete (RAC) exhibits lower CS compared to natural aggregate concrete. Several variables, such as the water-cement ratio, the strength of the parent concrete, recycled aggregate replacement ratio, density, and water absorption of recycled aggregate, all impact the RAC's CS. Many studies have been carried out to ascertain the influence of each of these elements separately. However, it is difficult to investigate their combined effect on the CS of RAC experimentally. Experimental investigations entail casting, curing, and testing samples, which require considerable work, expense, and time. It is vital to adopt novel methods to the stated aim in order to conduct research quickly and efficiently. The CS of RAC was predicted in this research utilizing machine learning techniques like decision tree, gradient boosting, and bagging regressor. The data set included eight input variables, and their effect on the CS of RAC was evaluated. Coefficient correlation (R2), the variance between predicted and experimental outcomes, statistical checks, and k-fold evaluations, were carried out to validate and compare the models. With an R2 of 0.92, the bagging regressor technique surpassed the decision tree and gradient boosting in predicting the strength of RAC. The statistical assessments also validated the superior accuracy of the bagging regressor model, yielding lower error values like mean absolute error (MAE) and root mean square error (RMSE). MAE and RMSE values for the bagging model were 4.258 and 5.693, respectively, which were lower than the other techniques employed, i.e., gradient boosting (MAE = 4.956 and RMSE = 7.046) and decision tree (MAE = 6.389 and RMSE = 8.952). Hence, the bagging regressor is the best suitable technique to predict the CS of RAC. [ABSTRACT FROM AUTHOR]

The main factor that alters the quality of recycled concrete aggregate (RCA) is the paste adhered to the natural aggregate (NA). Since it causes weakening of the interfacial transition zone (ITZ) between the aggregate and the cementitious paste, it becomes a determining factor for the mechanical behavior of concrete. It turns out that it is critical to enhance this interface by improving the surface of the aggregate or by removing the paste adhered to the NA. Considering the variety of methods for removing paste adhered to RCA—namely using acids such as hydrochloric acid (HCl), sulfuric acid (H2SO4), and phosphoric acid (H3PO4), among others—this paper presents a review of treatments for the removal of adhered paste using acidic solutions on the RCA, and their influence on the mechanical properties and durability of concrete produced with RCA. Pearson's correlation was used in the statistical analysis to determine the linear relationship of the main factors—for instance, immersion time, acidic solution, and aggregate size—involved in the removal of the paste in the RCA. [ABSTRACT FROM AUTHOR]

The practical use of recycled concrete aggregate produced by crushing concrete waste reduces the consumption of natural aggregate and the amount of concrete waste that ends up in landfills. This study investigated two methods used in the production of fine recycled concrete aggregate: (1) a method that produces fine as well as coarse aggregate, and (2) a method that produces only fine aggregate. Mortar specimens were tested using a variety of mix proportions to determine how the characteristics of fine recycled concrete aggregate affect the physical and mechanical properties of the resulting mortars. Our results demonstrate the superiority of mortar produced using aggregate produced using the second of the two methods. Nonetheless, far more energy is required to render concrete into fine aggregate than is required to produce coarse as well as fine aggregate simultaneously. Thus, the performance benefits of using only fine recycled concrete aggregate must be balanced against the increased impact on the environment. [ABSTRACT FROM AUTHOR]

Concrete is the most widely used building material, but it is also a recognized pollutant, causing significant issues for sustainability in terms of resource depletion, energy use, and greenhouse gas emissions. As a result, efforts should be concentrated on reducing concrete's environmental consequences in order to increase its long-term viability. In order to design environmentally friendly concrete mixtures, this research intended to create a prediction model for the compressive strength of those mixtures. The concrete mixtures that were used in this study to build our proposed prediction model are concrete mixtures that contain both recycled aggregate concrete (RAC) and ground granulated blast-furnace slag (GGBFS). A white-box machine learning model known as multivariate polynomial regression (MPR) was developed to predict the compressive strength of eco-friendly concrete. The model was compared with the other two machine learning models, where one is also a white-box machine learning model, namely linear regression (LR), and the other is the black-box machine learning model, which is a support vector machine (SVM). The newly suggested model shows robust estimation capabilities and outperforms the other two models in terms of R2 (coefficient of determination) and RMSE (root mean absolute error) measurements. [ABSTRACT FROM AUTHOR]

The paper focuses on investigating the effect of impregnation of recycled concrete aggregate on the mechanical and durability properties of concrete using this aggregate. Cement paste, limewater and diluted water glass were used to impregnate the aggregate. Both a single impregnation and a double impregnation using two different solutions were carried out. A total of four groups of concrete series, with two values of w/c ratio (0.45 and 0.60), were made. Concrete made using the impregnated aggregate was tested and the results were compared with those of concrete made using untreated recycled aggregate of the same kind. The results indicate that impregnation of aggregate improves the mechanical properties of concrete in many cases but reduces its resistance to cyclic freezing and thawing. Furthermore, in the case of impregnation with two solutions, the order in which the impregnants are applied influences the effect obtained. Using the results received, the impregnation methods were ranked in order from best to worst. The best impregnation method proved to be with cement paste, followed by diluted water glass, while the worst results were obtained with limewater, followed by diluted water glass. [ABSTRACT FROM AUTHOR]

This work aims to investigate different predictive models for estimating the unconfined compressive strength and the maximum peak strain of non-structural recycled concretes made up by ceramic and concrete wastes. The extensive experimental campaign carried out during this research includes granulometric analysis, physical and chemical analysis, and compression tests along with the use of the 3D digital image correlation as a method to estimate the maximum peak strain. The results obtained show that it is possible to accurately estimate the unconfined compressive strength for both types of concretes, as well as the maximum peak strain of concretes made up by ceramic waste. The peak strain for mixtures with concrete waste shows lower correlation values. [ABSTRACT FROM AUTHOR]

In the present study, a recycled concrete aggregate (RCA) coating treatment using a cement paste dissociation agent (CPDA) with different mixing methods was newly incorporated in RCA concrete mixtures. First, a preliminary test program was conducted to determine the proper dosage of the CPDA solution throughout its RCA concrete test results from compressive strength, flexural strength, and elastic modulus. Then, a series of experimental tests were carried out to investigate the effect of RCA coating treatment, different mixing method such as the equivalent mortar volume (EMV) method and conventional method, and different RCA replacement ratios on durability test results of RCA concrete such as drying shrinkage values and rapid chloride penetration test (RCPT) values. The test results showed that all RCA concretes mixed with the coated RCAs were found to be workable regardless of different mix methods, with the slump and air contents of all the mixes being almost identical. All the concrete specimens, which were mixed with the coated RCAs with CPDA solution, represented lower drying shrinkage and RCPT values than those mixed without RCA coating treatment, regardless of different mix proportioning methods or RCA replacement ratios. This holds for the concrete specimens proportioned with the EMV method, regardless of different RCA replacement ratios. [ABSTRACT FROM AUTHOR]

This article deals with the possibility of utilization of secondary-raw materials as a natural sand replacement in concrete. Four types of waste construction materials were examined—recycled aggregate from four different sources. The natural aggregate was examined as well as used as the reference sample. All the samples were tested to evaluate the water absorption, particle size distribution, and particle density. The basic chemical reactions in the view of ecotoxicology are investigated and measured based on Czech standards. Chemical analysis, Lemna growth inhibition test, freshwater algae, daphnia acute, and mustard germination toxicity test were made and discussed in this paper. Based on the physical and geometrical properties and ecotoxicology of examined waste materials, this work evaluated them as suitable for utilization in concrete as a sand replacement. [ABSTRACT FROM AUTHOR]

Recently, concerns have been rising about the impact of increasing the depletion of natural resources and the relevant generation of construction and demolition waste, on the environment and economy. Therefore, several efforts have been made to promote sustainable efficiency in the construction industry and the use of recycled aggregates derived from concrete debris for new concrete mixtures (leading to so-called recycled aggregate concrete, RAC) is one of the most promising solutions. Unfortunately, there are still gaps in knowledge regarding the durability performances of RAC. In this study, we investigate durability of structural RAC subjected to wet-dry cycles. We analyze the results of an experimental campaign aimed at evaluating the degradation process induced by wetting and drying cycles on the key physical and mechanical properties of normal- and high-strength concrete, produced with coarse recycled concrete aggregates (RCAs) of different sizes and origins. On the basis of the results we propose a degradation law for wetting and drying cycles, which explicitly makes a possible correlation between the initial concrete porosity, directly related to the specific properties of the RCAs and the resulting level of damage obtained in RAC samples. [ABSTRACT FROM AUTHOR]

Sand has been considered to be something of an immeasurable quantity. There are many indications that this view is no longer valid and that the limiting of natural aggregates usage is doubly justified. Firstly, the extraction of natural aggregates is expensive and has a huge impact on the environment. The main issues in sand and gravel mining are the large areas that are affected, ground water level changes, illegal mining, unsuitability of desert and marine sand, and costs of transport. Secondly, metallurgical waste can be used as a substitute for natural aggregates. This is doubly beneficial—the waste is recycled and the use of natural aggregates is reduced. Waste is stored in landfills that take up large areas and there is also the possibility of ground and groundwater pollution by hazardous compounds. The research presented in this article focuses on the technological conditions of using metallurgical waste in its original form and as a component of recycled concrete aggregate (RCA). The use of metallurgical sludge waste or crushed or round RCA to produce concrete deteriorates the consistency and does not significantly affect the air content and density of the concrete mix. RCA lowers the density of hardened concrete. Metallurgical sludge waste or RCA usage adversely affect the absorbability and permeability of concrete. Concrete containing metallurgical sludge waste is of higher compressive strength after 7 and 28 days, with up to 60% of waste as a sand replacement. RCA concrete achieved higher compressive strength also. [ABSTRACT FROM AUTHOR]

Creating models based on empirical data and their statistical measurements have been used for a long time in the economic sciences. Increasingly, these methods are used in the technical sciences, such as construction and geotechnical engineering. This allows for reducing the costs of geotechnical research at the design stage. This article presents the research carried out on Recycled Concrete Aggregate (RCA) material with is reclaimed crushed concrete rubble. Permeability tests were carried out using the constant head method. Tests were conducted on blends of RCA with the following particle size ranges: 0.02–16 mm, 0.05–16 mm, 0.1–16 mm, and 0.2–16 mm. The gradients used during the tests were between 0.2 to 0.83, which corresponds to gradients encountered in earth construction and are below the critical gradient. Directly from the tests, the flux velocity for the range of tested gradients were calculated based on filtered water volume measurements. The values of the permeability coefficient (k) were then recalculated. Finally, statistical methods were used to determine which physical parameters of the tested material affect the permeability coefficient. The physical parameters selected from the statistical analysis were used to create a model describing the phenomenon. The model can be used to determine the permeability coefficient for a mixed RCA material. The article ends with conclusions and proposals concerning the use of models and the limits of their applicability. [ABSTRACT FROM AUTHOR]

Concrete is a building material commonly used for ages. Therefore, in the result of repairs or demolition of building structures, large amounts of concrete rubble are created, which requires appropriate management. The aim of the realized research was to determine the influence of heat and mechanical treatment of concrete rubble on the properties of recycled aggregate concrete. The research experiment included 12 series, with three variables: X1—roasting temperature (300, 600, 900 °C), X2—time of mechanical treatment (5, 10, 15 min), X3—content of coarse recycled aggregates (20, 40, 60% by volume). Two additional series containing recycled aggregate without treatment and natural aggregate were also prepared. Established properties of individual aggregates have confirmed a positive effect of thermo-mechanical treatment. Then, based on the results of compressive strength, flexural strength, Young's modulus, volumetric density, water absorption, water permeability and capillarity, the most favourable parameters of heat and mechanical treatment of concrete were determined. The test results showed that appropriate treatment of concrete rubble allows to obtain high-quality coarse aggregate and valuable fine fraction. This was also confirmed by the macro- and microscopic observations of the aggregate and separated cement paste. Works realized on the concrete recycling method resulted in obtaining a patent PAT.229887. [ABSTRACT FROM AUTHOR]