Search

A provisionalization sequence is essential for obtaining a predictable final prosthetic outcome. An assessment of the mechanical behavior of interim prosthetic materials could orient clinicians towards selecting an appropriate material for each clinical case. The aim of this study was to comparatively evaluate the mechanical behavior-with compressive and three-point flexural tests-of certain 3D-printed and conventional resins used to obtain interim fixed dental prostheses. Four interim resin materials were investigated: two 3D-printed resins and two conventional resins (an auto-polymerized resin and a pressure/heat-cured acrylic resin). Cylindrically shaped samples (25 × 25 mm/diameter × height) were obtained for the compression tests and bar-shaped samples (80 × 20 × 5 mm/length × width × thickness) were produced for the flexural tests, observing the producers' recommendations. The resulting 40 resin samples were subjected to mechanical tests using a universal testing machine. Additionally, a fractographic analysis of failed samples in bending was performed. The results showed that the additive manufactured samples exhibited higher elastic moduli (2.4 ± 0.02 GPa and 2.6 ± 0.18 GPa) than the conventional samples (1.3 ± 0.19 GPa and 1.3 ± 0.38 GPa), as well as a higher average bending strength (141 ± 17 MPa and 143 ± 15 MPa) when compared to the conventional samples (88 ± 10 MPa and 76 ± 7 MPa); the results also suggested that the materials were more homogenous when produced via additive manufacturing.

The purpose of this study was to analyze the oxidative stress level and inflammatory status of saliva in the presence of certain materials used for obtaining interim prosthetic restorations. Four types of interim resin materials were investigated: a pressure/heat-cured acrylic resin (Superpont C+B, SpofaDental a.s Czech Republic, /KaVo Kerr Group), a milled resin (Telio CAD polymethyl methacrylate, Ivoclar Vivadent AG, Liechtenstein), a 3D printed resin (NextDent C&B MFH, NextDent by 3D Systems, the Netherlands), and a pressure/heat-cured micro-filled indirect composite resin (SR Chromasit, Ivoclar Vivadent AG, Liechtenstein). The disk-shaped resin samples (30 mm diameter, 2 mm high) were obtained in line with the producers' recommendations. The resulting resin specimens were incubated with saliva samples collected from twenty healthy volunteers. In order to analyze the antioxidant activity of the tested materials, certain salivary parameters were evaluated before and after incubation: uric acid, gamma glutamyl transferase (GGT), oxidative stress responsive kinase-1 (OXSR-1), and total antioxidant capacity (TAC); the salivary levels of tumor necrosis factor (TNFα) and interleukin-6 (IL-6) (inflammatory markers) were measured as well. The obtained results are overall favorable, showing that the tested materials did not cause significant changes in the salivary oxidative stress level and did not influence the inflammatory salivary status.

Carotenoids loaded in nanoparticles should be regarded as a promising way to increase the availability in healthy cells and to induce apoptosis in cancer. Lutein is a carotenoid that, in contrast to beta-carotene, has no known toxicities. Oral cancer represents one of the most frequent types of cancer world-wide with an incidence rate of about 9% of all types of cancer. Almost 95% of all oral cancers are represented by squamous cell carcinomas (OSCC). The aim of this study was to review and analyse the effects of lutein and Poly(d,l-lactide-co-glycolide) (PLGA) Nps containing lutein (Lut Nps) on oxidative stress biomarkers (OXSR-1, FOXO-3, TAC) and collagen degradation biomarker-MMP-9, in human cells BICR10 of buccal mucosa squamous carcinoma. Lut Nps were prepared by the emulsion-solvent evaporation method. MMP, OXSR-1, TAC, FOXO-3 and MMP-9 were measured in tumour cell lysates by the ELISA technique. Our results have shown that in Lut 100 cells and Lut Nps the OXSR1 ( p < 0.001, p < 0.001) and TAC ( p < 0.001, p < 0.001) values were significantly higher than in control cells. The Lut 100 and Lut Nps FOXO-3 levels revealed no significant differences versus the control. MMP-9 levels were significantly reduced ( p < 0.001) in the Lut Nps cells versus control cells. In our study conditions, lutein and lutein Nps did not trigger an oxidative stress by ROS induction. However, lutein Nps treatment seemed to have a positive effect, by downregulating the MMP-9 levels. Loaded in Nps, lutein could be regarded as a protective factor against local invasiveness, in whose molecular landscape MMPs, and especially MMP-9 are the main actors.

This paper's primary aim is to outline relevant aspects regarding the biocompatibility of PMMA (poly(methyl methacrylate))-based materials used for obtaining interim prosthetic restorations, such as the interaction with oral epithelial cells, fibroblasts or dental pulp cells, the salivary oxidative stress response, and monomer release. Additionally, the oral environment's biochemical response to modern interim dental materials containing PMMA (obtained via subtractive or additive methods) is highlighted in this review. The studies included in this paper confirmed that PMMA-based materials interact in a complex way with the oral environment, and therefore, different concerns about the possible adverse oral effects caused by these materials were analyzed. Adjacent to these aspects, the present work describes several advantages of PMMA-based dental materials. Moreover, the paper underlines that recent scientific studies ascertain that the modern techniques used for obtaining interim prosthetic materials, milled PMMA, and 3D (three-dimensional) printed resins, have distinctive advantages compared to the conventional ones. However, considering the limited number of studies focusing on the chemical composition and biocompatibility of these modern interim prosthetic materials, especially for the 3D printed ones, more aspects regarding their interaction with the oral environment need to be further investigated., Competing Interests: The authors declare no conflict of interest.