Search

The Heusler type Ni–Mn- Z (Z = Ga, ln, Sn, or Sb) alloys with magneto-structural transformations (MSTs) have received widespread research interests due to the exhibition of multifunctional characters. To further understand MSTs and improve the magnetocaloric performance of these alloys, in this work, the Ti doped Ni 48 Cu 2 Mn 36 Sn 14-x Ti x (x = 0, 1, 2, 3) ribbons have been fabricated and systematically determined with regard to the structural, magnetic, and magnetocaloric properties by means of X-ray diffraction (XRD), scanning electron microscope (SEM), differential scanning calorimetry (DSC), and magnetization measurements. All the ribbons are found to crystallize in the ordered cubic L2 1 austenite phases at room temperature and with the equiaxed austenite morphology. With the increasing Ti content, the average grain size and the MST temperature increase but the austenite Curie temperature (T A C) decrease gradually. Moreover, the thermal hysteresis and magnetic hysteresis loss are greatly reduced with the Ti doping. The value of average hysteresis loss (AHL) is reduced from 86 Jkg−1 for Ti0 to 25.5 Jkg−1 for Ti3 ribbon under 7 T. Additionally, enhanced magnetocaloric effect has been observed by Ti-doping. With the magnetic field change (ΔH) of 0–7 T, the largest value of magnetic entropy change reaches 15.4 Jkg−1K−1 (Ti2) among the Ni 48 Cu 2 Mn 36 Sn 14-x Ti x ribbons. The present work indicates that reasonable Ti doping could be a useful way to regulation the MSTs and improve the magnetocaloric performance of the Heusler type Ni–Mn–Sn-based alloys. • The Hesuler type Ni 48 Cu 2 Mn 36 Sn 14-x Ti x (x = 0, 1, 2, 3) ribbons are fabricated. • The structural, magnetic and magnetocaloric properties were investigated. • Ti doping could be a useful way to regulation the MSTs. • Enhanced magnetocaloric performances has been observed by Ti-doping. [ABSTRACT FROM AUTHOR]

In this paper, Cu-based and Ni-based filler metals were used to obtain laser-CMT hybrid welded copper/stainless steel (Cu/SS) joints. The effect of wire compositions on the microstructure and mechanical properties of T2 Cu/304 SS dissimilar metal joint was studied. The results showed that Fe–Cu liquid phase separation occurred in the fusion zone of the Cu-based weld, and Cu penetration cracks appeared in the heat-affected zone (HAZ) on the steel side. The Cu penetration cracks formation is derived from supersaturated Cu atoms penetrating, gathering and merging at the steel side fusion line along the austenite grain boundaries. The penetration cracks can be eliminated effectively by the Ni-based filler metal, because the diffusion of Cu into the fusion zone and the HAZ on the steel side is limited significantly by the increase of Ni content. The Ni-based weld consisted of dendrite grains in the fusion zone, and Fe-rich blocks and Ni-rich islands nearby the HAZ of Cu-side. • Defect-free weld was obtained by laser-CMT hybrid welding with Ni-based wire. • Cu-based weld penetration cracks mechanism was illustrated. • The microstructures of Cu-based and Ni-based welds were compared. • The mechanism of inhibition of penetration cracks in Ni-based weld was discussed. [ABSTRACT FROM AUTHOR]

The structural, magnetic, and magnetocaloric properties of Ni 44 Mn 45-x Sn 11 Fe x (x = 0, 1, 2 and 3) Heusler alloys have been studied detailly by means of X-ray diffraction, differential scanning calorimetry, and magnetization measurements. The martensitic transition temperature (T M) and austenite Curie temperature (T A C) increase gradually with increasing Fe content. Large differences in magnetization between the ferromagnetic austenite and weakly magnetic martensite phases and obvious thermal hysteresis have also been observed during the martensite transformation. With the magnetic field change up to 0–7 T, the maximum value of magnetic entropy changes reaches 26.7 and 23 J kg−1K−1 for x = 1 and 2, respectively, which are much larger than the undoped sample (9.8 J kg−1K−1). Whereas, the effective refrigerant capacity RC eff reduced due to Fe doping increased the hysteresis loss. The alloy for x = 1 has highest RC value of 172 (255) J kg−1 for a magnetic field change of 0–5 T (0–7 T), furthermore, a large magnetic entropy change and moderate RC eff has been obtained around room temperature. • Fe-doped Ni44Mn45-xSn11Fex (x = 0, 1, 2 and 3) Heusler alloys were fabricated. • Structural and magnetic properties of Ni44Mn45-xSn11Fex were investigated. • Considerable magnetocaloric performances in Ni44Mn44Sn11Fe were realized. [ABSTRACT FROM AUTHOR]