Search

In the present work, advanced aluminium metal matrix composite reinforced by nanomaterials is reported. The materials used for the experiments are AA6061 aluminium alloy, compounded with inorganic nanotubes (INT) and fullerene-like (IF) nanoparticles of WS 2 . Aluminium metal matrix composite with different weight percentage (0.1–0.5 wt%) of the INT and IF were prepared. Both the AA6061 aluminium and the aluminium metal matrix nanocomposites (MMCs) were re-melted by the stirring-casting method. Mechanical properties and microstructure analysis of the nano-MMCs were conducted. The measurements have shown that the hardness, yielding strength, ultimate tensile strength, and ductility were improved by up to 68% compared to the neat alloy for nanoparticles concentrations the range of 0.2 wt%. Metallography microstructure analysis showed that increasing the WS 2 INT or IF nanoparticles weight percentage in aluminium metal matrix composite, resulted in a more refined grains. The grain size of the composite matrix was reduced by up to 48.4% compared with that of neat AA6061 alloy ingot. Scanning electron microscope (SEM) analysis showed that addition of 0.5 wt% of WS 2 nanotubes into the Al matrix resulted in INT agglomeration which had deleterious effect on the tensile strength. The composite materials reinforcement mechanism was studied. This analysis showed that the improved mechanical properties of the metal nanocomposites can be predominantly attributed to the differences in thermal expansion coefficients of the WS 2 INT (or WS 2 IF nanoparticle) and the AA6061 alloy. [ABSTRACT FROM AUTHOR]

AZ91 reinforced with four different concentrations (0,0.3,0.6,1)wt% of WS 2 micro particles were fabricated using stir casting method. The samples were deformed by equal channel angular pressing (ECAP) after homogenization. The scanning electron microscopy and X-ray diffraction were used to investigate the microstructure and phase composition respectively. The results reveal that rod-like precipitates produced during the homogenization process are refined and bounded in the grain boundaries by the combined effect of WS 2 enrichment and increasing number of passes of ECAP. The needle precipitates are eminent in 1pass 0.3 wt%WS 2 /AZ91. The β-Mg 17 Al 12 and extracted Al particles are dissolved and secondary phases are produced by dynamic recrystallization after 2pass 1 wt%WS 2 /AZ91. The maximum crystallite size and microstrain distribution have been observed for 1pass 0.6 wt%WS 2 /AZ91. The mechanical properties investigation represents that 2pass 0.6 wt%WS 2 /AZ91 has optimal yield strength and ultimate tensile strength. The (22.143)%, (44.735)% and (92) % increment in yield strength, ultimate tensile strength and elongation have been observed in 2pass 1 wt%WS 2 /AZ91 compared with homogenized monolithic AZ91 alloy respectively. The maximum young's modulus (6696.218MPa) has been found for 1pass homogenized WS2/AZ91 and minimum (4108.165MPa) for homogenized 0.6 wt%WS 2 /AZ91. The ECAP deformed 1pass 0.3 wt%WS 2 /AZ91 exhibits the maximum strain hardening rate. The YTS, UTS, and elongation are (30.41) %, (47.6) % and (51.9)% increased after 2pass-0.6 wt%WS 2 /AZ91. [ABSTRACT FROM AUTHOR]

Abstract: This study investigates the effects of heat treatment on the morphology of long-period stacking ordered phase (LPSO) and the corresponding mechanical properties of Mg–9Gd–xEr–1.6Zn–0.6Zr (1–4wt%) using optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectrometry, X-ray diffraction, transmission electron microscopy, and tensile tests. The microstructure analysis of the as cast alloys showed that the volume fraction of the (Mg, Zn)3(Gd, Er) phase increased with increasing Er content. The (Mg, Zn)3(Gd, Er) phase in grain boundaries transformed into the 14H-LPSO phase Mg12Zn(Gd, Er) after heat treatment between 400°C and 515°C. The bulk shaped LPSO phases distributed along the grain boundaries produced isometric crystal grains in and enhanced the ductility of the as-extruded alloys. However, the lamellar LPSO phases precipitating in the grain interior induced strip-shaped grains in and improved the strength of the as-extruded alloys. [Copyright &y& Elsevier]

The ageing behavior of as-extruded Mg-1.5Gd-1.3Y-0.6Zn-0.6Mn (at%) alloy was investigated. The strength and ductility are simultaneously improved during ageing at the peak hardness platform. The alloy aged for 100 h exhibits ultrahigh ultimate tensile strength (UTS) of 538 MPa and good elongation to failure (EL) of 13.1%. [ABSTRACT FROM AUTHOR]