Search

A Ti3C2 MXene/Ti composite powder was developed through surface modification and powder coating for producing a high-performance titanium matrix composites (TMCs) by laser power bed fusion. Introducing MXene rarely changed the original sphericity and flowability of Ti powder while it slightly enhanced the laser absorption capacity of Ti powder. The printing conditions in turn affected the morphology and distribution of MXene in as-printed composites. At optimised printing parameters, majority of MXene with high structural integrity and uniform distribution remained along the grain boundaries of as-printed composites, and a combination of high surface quality, geometrical accuracy and densification was obtained. The remaining MXene played the synergy of pulling-out effect and load transfer role, which increased the yield strength from 530 to 710 MPa, while retaining good ductility (elongation of 19.8%). Compared with ASTM standard cast Ti64 alloy, our MXene/Ti composites also exhibited superior comprehensive tensile properties and excellent strength-ductility synergy. [ABSTRACT FROM AUTHOR]

High entropy alloys (HEAs), consisting of five or more elements with nearly equal atomic composition with one another (5–35%), are new-generation alloys that have attracted signifi)cant interest since their advent in 2004 because of their unique structural and mechanical properties and thermodynamic and chemical stability. Some characteristics, including high mechanical strength at elevated temperatures, high ductility and fracture toughness at cryo)genic temperatures and high corrosion, erosion and wear resistance, have been demonstrated for HEAs that outperform traditional alloys and superalloys. Laser-cladding (LC) is an additive manufacturing technique that has good feasibility in designing and processing HEAs for advanced structural components and protective coatings. This overview provides a glimpse of recent advances in LC of HEAs in terms of design fundamentals, metallurgical phase and microstructure, specific properties for advanced coating applications and the effect of ceramic particles reinforcement in LC deposition of HEA coatings. [ABSTRACT FROM AUTHOR]

Polycrystalline nanoparticles of Al-doped and Ce-co-doped ZnO were processed through sol)gel co-precipitation. Crystallite sizes determined from XRD were in the range of 10.90 to 48.77 nm. FTIR spectra indicated a stretching mode of Zn-O bond. The insertion of Al and Ce at Zn-O site created Al-O and Ce-O bonds. UV-vis spectra favoured the formation of impurity levels by doping and co-doping. Their overlapping with the conduction band edge led to the reduction of band-gap. Blue-green emission which arises from radiative recombination of a photogenerated hole with an electron occupying oxygen vacancy was observed in photo)luminescence spectra. FESEM suggested granular growth in undoped ZnO which changed to diverse structures such as nano-bar and cluster of elongated grains. Significant improvement in room temperature ferromagnetism (RTFM) was noticed by co-doping of Ce in Al-doped ZnO. Formation of bound magnetic polarons (Ce3+-Vo-Ce3+) was the primary mechanism responsible for the improvement in RTFM. [ABSTRACT FROM AUTHOR]

Laser-induced periodic surface structures (LIPSS) on biomedical stainless steel in air and water were systematically studied. The LIPSS exhibit in-plane curves near the ripple centres in the individual tracks of laser scan and the curving was opposite to the laser scan direction. The collective in-plane curving of LIPSS, a hitherto unknown feature for single train pulsed laser processing, is attributed to the accumulative effect of laser ablation and redeposition, which modifies the interference between the surface scattered wave and the incident laser beam. Combinations of media, scan-speed, and laser fluence, showed that the roughness can be increased by slowing the scan-speed. Ripples fabricated in the flowing water with slow scan-speed and high laser power are helpful for the hydrophilicity of biomaterials. A contact angle as low as 47.00 ± 9.35° is obtained towards high surface hydrophilicity. The results provide new insights on LIPSS about their formation and biomedical applications. [ABSTRACT FROM AUTHOR]

Anodisation with electrochemical cathodic deposition method was employed to modify the surface of Ti implants with a bilayer coating made of Sr- doped titania (Sr-TiO2) and hydroxyapatite doped with magnesium (Mg-HAp). The Mg-HAp/Sr-TiO2 bilayer coating was compared with pure TiO2 and Sr-TiO2 single-layer coating. The Sr incorporation into TiO2 and Mg substitution into HAp strengthened their bioactive properties. The tensile test indicated increase in the mechanical strength of the bilayer coated substrate compared to pure TiO2 substrate. Moreover, the study indicated that the Sr and Mg ions were uniformly incorporated into the Mg-HAp/Sr-TiO2 bilayer coating with significantly higher roughness and hydrophilicity compared to the control. In vitro studies with osteoblasts cells had a superior response to the Mg-HAp/Sr-TiO2 bilayer surface. It was found that a bilayer Mg-HAp/Sr-TiO2 coating on Ti implants promotes bioactivity and has superior adhesion strength necessary for osseointegration and bone healing. [ABSTRACT FROM AUTHOR]