Search

Third generation γ-titanium aluminides with nominal compositions Ti–45Al–5Nb–0.2B–0.2C and Ti–45Al–10Nb–0.2B–0.2C were investigated to identify the phase transformation and their morphological stability with temperature. Electron microscopy and differential scanning calorimetry were employed for the characterization of phases and for recording the corresponding transformations, respectively. It has been inferred that the order–disorder transformation temperatures α2 → α increased with increasing Niobium (Nb), while the α-transus temperature decreases. The stability of the microstructure for both alloys with temperature were also investigated. Mass change measured for the heating rates 20 °C s−1 and 30 °C s−1 reveals that the alloy Ti–45Al–10Nb–0.2–0.2C shows stability up to 1100 °C, and the alloy Ti–45Al–5Nb–0.2B–0.2C is stable up to 900 °C. The orientation relationship between the phases indicates that with the change in shape of the α phase from lamellar to equiaxed, it deviates from the Blackburn orientation relationship.

The evolution of microstructure and texture during selective laser melting (SLM) of silver alloy—sterling silver 925 (AM Ag925) has been investigated and analyzed vis-a-vis cast sterling silver (AC Ag925). The microstructure of AM Ag925 was characterized by a single-phase silver-rich face-centered cubic solid solution with dendritic morphology, along with some locally distributed micro-segregated copper–germanium (Cu–Ge)-rich regions. Each adjacent dendritic feature consists of Ag–Cu-rich and Ag–Ge-rich regions and appears as alternate dark and bright regions. On the other hand, the as-cast AC Ag925 microstructure comprises Ag and Cu phases. Specific heat treatment was employed, which led to an equiaxed microstructure in AM Ag925 with Cu distributing along grain boundaries while the microstructure of AC Ag925 had Cu precipitates inside the matrix. Bulk texture studies revealed that the solidified textures were very weak for AM Ag925, and a random texture is observed. On the other hand, for the AC Ag925 specimens, a typical fiber texture is observed. Both AC Ag925 and AM Ag925 showed significant deviation from $$\left\langle {100} \right\rangle$$ solidification texture and influences the mechanical properties.

Microstructure evolution and texture development during cold rolling of a Ti15333 alloy were systematically investigated in the present work. Texture was simulated using mean-field [Visco-Plastic Self-Consistent (VPSC) and Taylor] models. Evolution of crystallographic texture was also simulated using the Visco-Plastic Fast Fourier Transform (VPFFT) model. The as-received samples (in the hot-forged and hot-rolled condition) were cold rolled unidirectionally up to 20, 40, 60 and 80 pct thickness reductions. Increase in the cold-rolling reduction resulted in changes in the crystallographic texture as well as grain morphology. The initial hot-rolled sample consisted of in-grain shear bands that were aligned approximately ± 35 to 40 ° with respect to the sample rolling direction. Shear band density gradually increased with the increase in cold-rolling reduction, and these bands usually represent narrow zones of intense strain. α (RD//〈110〉) and γ (ND//〈111〉) fibers were observed in all the cold-rolled samples. The volume fraction of both these fibers was found to be highest for the 80 pct deformed sample. For mean-field simulations, the normalized difference of the texture index (normalized TIdiff) was found to be a good criterion to represent the match between the simulated and experimental texture. The affine model (VPSC) was found to give a good match with the experimental texture compared to the Taylor models. The γ-fiber and α-fiber were always overestimated in mean-field VPSC simulations. Extensive shear band formation could be the possible reason for mismatch between the simulated and experimental texture. For VPFFT simulations, the general texture evolution involved the intensification of the γ-fiber and α-fiber texture. Simulated texture was reasonably well predicted quantitatively with VPFFT, analyzed based on the volume fraction of the different texture fibers/components.

In the present investigation, the evolution of texture and microstructure during incremental sheet forming was investigated. Hot-rolled sheets of commercially pure titanium were subjected to single-point incremental forming to obtain truncated pyramid geometries. It was observed from texture measurements that there was splitting of basal poles along the transverse direction. Moreover, a significant number of twins was observed in the deformed microstructure with the fraction of extension twins being highest compared to other variants. The crossing of deformation twins, formation of twin lamellar structure and formation of secondary extension twins within primary contraction twins were additionally observed. The state of deformation in the pyramid walls was analyzed via finite element method which in turn was used as input for carrying out crystallographic texture simulations via visco-plastic self-consistent simulations. It was observed that the state of deformation in the wall regions is plain strain compression plus through-thickness shear.

Ti-Nb-based low modulus metastable β-titanium alloys are popular choice for orthopedic implant materials. The performance of these materials could be affected by variation in crystallographic texture developed during processing. In the present study, texture evolution during unidirectional rolling and multi-step cross-rolling of the alloys Ti-34Nb-2Ta-3Zr-0.5O (TNTZO) and Ti-34Nb-2Ta-0.5O (TNTO) (in wt pct) has been studied. In both the alloys, the rolling texture is characterized by the absence of RD∥〈110〉 fiber, and cross-rolling leads to a stronger texture than unidirectional rolling. However, the prominent texture components in the cross-rolled condition are different for the two alloys. The TNTZO alloy shows the formation of a strong γ-fiber (ND∥〈111〉) along with {001}〈110〉 components while in TNTO, the texture is dominated by strong {001}〈110〉 component. These experimental results have been analyzed by simulations using viscoplastic self-consistent model and further validated by microstructural analysis using electron back scattered diffraction (EBSD). The deformation texture evolution has been attributed to a predominantly $$ \left\{ {11\overline{2} } \right\}\left\langle {111} \right\rangle $$ slip. The simulated texture of Ti-34Nb-2Ta-0.5O alloy shows a minor deviation from the experimental texture, which can be related to the reduced stability of this alloy due to the absence of Zr.

In this study, the effect of aluminum (Al) addition to a manganese (Mn) steel Fe-12Mn-0.5C in regard to the change in stacking fault energy (SFE) and the consequent evolution of deformation microstructure and texture were investigated during cold rolling. An analysis of the texture and microstructure was performed to understand the deformation micro-mechanisms. Deformation micro-mechanisms were substantiated by the estimation of dislocation density and the arrangement of dislocations in the deformed microstructure by X-ray line profile analysis, which revealed significant changes in the dislocation structure with the addition of Al. Three stages of deformation mechanism were observed in all Al-added compositions. In the early stages of deformation, slip as well as twinning prevailed. In the intermediate stage, twinning took over completely and at large strains, macroscopic shear bands became the dominant deformation mode. An increase in the propensity of nanometer-sized deformation twins was observed with rolling strain. However, the addition of Al decreased the overall twin fraction in the deformed microstructure. The theoretical twinning stress was calculated to explain the crucial role of SFE on the occurrence of deformation twins in these steels. The deformation texture was predominantly of the brass type for all the Al-added compositions; however, appreciable differences were seen with Al content. The 〈111〉//ND γ-fiber, which develops in Al-free Fe-12Mn-0.5C, completely disappeared in 3 wt pct Al-containing material.

Microstructure and crystallographic texture evolution during single- and multiple-pass friction stir processing (FSP) of an age-hardenable aluminum alloy 2024 (Al-Cu-Mg) was investigated. Multiple-pass experiments were carried out using two different processing strategies, multi-pass FSP, and multi-track FSP. Effect of a post-FSP heat treatment above and below the solutionizing temperature of the alloy was also studied. FSP experiments were carried out using an optimal set of parameters. Characterization tools used in the study include scanning electron microscopy (SEM), electron back-scattered diffraction (EBSD), electron probe micro-analyser (EPMA), and X-ray diffraction (XRD). Microstructural features indicate the occurrence of particle stimulated nucleation (PSN) assisted dynamic recrystallization (DRX) as the dominant microstructural evolution mechanism in the nugget zone. Geometrical coalescence occurred, leading to the formation of some larger grains in the nugget zone. Heterogenous micro-texture distribution was observed in the nugget zone with the bulk textures consisting of FCC shear texture components dominated by A (1)*/A (2)* and C. Microstructure and texture in the nugget zone remained stable after both routes of multiple-pass processing, demonstrating the possibility of FSP to produce bulk volume of fine-grained materials. Post-FSP heat treatment indicated the stability of microstructure and texture up to 723 K (450 A degrees C) owing to relatively lower strain energies retained after FSP.

In the current study, correlation of microstructure evolution with bulk crystallographic texture formation during friction stir processing (FSP) of commercial aluminum alloys has been attempted. Electron back-scattered diffraction and X-ray diffraction techniques were employed for characterizing the nugget zone of optimum friction stir processed samples. Volume fraction of measured texture components revealed that the texture formation in aluminum alloys is similar irrespective of the alloy composition. Recrystallization behavior during FSP was more of a composition dependent phenomenon.

The effect of strain path change during rolling on the evolution of deformation texture has been studied for nanocrystalline (nc) nickel. An orthogonal change in strain path, as imparted by alternating rolling and transverse directions, leads to a texture with a strong Bs {110}aOE (c) 112 > component. The microstructural features, after large deformation, show distinct grain morphology for the cross-rolled material. Crystal plasticity simulations, based on viscoplastic self-consistent model, indicate that slip involving partial dislocation plays a vital role in accommodating plastic deformation during the initial stages of rolling. The brass-type texture evolved after cross rolling to large strains is attributed to change in strain path.

A Cu-Cu multilayer processed by accumulative roll bonding was deformed to large strains and further annealed. The texture of the deformed Cu-Cu multilayer differs from the conventional fcc rolling textures in terms of higher fractions of Bs and RD-rotated cube components, compared with the volume fraction of Cu component. The elongated grain shape significantly affects the deformation characteristics. Characteristic microstructural features of both continuous dynamic recrystallization and discontinuous dynamic recrystallization were observed in the microtexture measurements. X-ray texture measurements of annealing of heavily deformed multilayer demonstrate constrained recrystallization and resulted in a bimodal grain size distribution in the annealed material at higher strains. The presence of cube- and BR-oriented grains in the deformed material confirms the oriented nucleation as the major influence on texture change during recrystallization. Persistence of cube component throughout the deformation is attributed to dynamic recrystallization. Evolution of RD-rotated cube is attributed to the deformation of cube components that evolve from dynamic recrystallization. The relaxation of strain components leads to Bs at larger strains. Further, the Bs component is found to recover rather than recrystallize during deformation. The presence of predominantly Cu and Bs orientations surrounding the interface layer suggests constrained annealing behavior.

The first part of this study describes the evolution of microstructure and texture in Ti-6Al-4V-0.1B alloy during sub-transus rolling vis-a-vis the control alloy Ti-6Al-4V. In the second part, the static annealing response of the two alloys at self-same conditions is compared and the principal micromechanisms are analyzed. Faster globularization kinetics has been observed in the Ti-6Al-4V-0.1B alloy for equivalent annealing conditions. This is primarily attributed to the α colonies, which leads to easy boundary splitting via multiple slip activation in this alloy. The other mechanisms facilitating lamellar to equiaxed morphological transformations, e.g., termination migration and cylinderization, also start early in the boron-modified alloy due to small α colony size, small aspect ratio of the α lamellae, and the presence of TiB particles in the microstructure. Both the alloys exhibit weakening of basal fiber (ND||〈0001〉) and strengthening of prism fiber (RD||〈 $$ 10\bar{1}0 $$ 〉) upon annealing. A close proximity between the orientations of fully globularized primary α and secondary α phases during α → β → α transformation has accounted for such a texture modification.

In the current study, the evolution of microstructure and texture has been studied for Ti-6Al-4V-0.1B alloy during sub-transus thermomechanical processing. This part of the work deals with the deformation response of the alloy by rolling in the (α + β) phase field. The (α + β) annealing behavior of the rolled specimen is communicated in part II. Rolled microstructures of the alloys exhibit either kinked or straight α colonies depending on their orientations with respect to the principal rolling directions. The Ti-6Al-4V-0.1B alloy shows an improved rolling response compared with the alloy Ti-6Al-4V because of smaller α lamellae size, coherency of α/β interfaces, and multiple slip due to orientation factors. Accelerated dynamic globularization for this alloy is similarly caused by the intralamellar transverse boundary formation via multiple slip and strain accumulation at TiB particles. The (0002)α pole figures of rolled Ti-6Al-4V alloy shows “TD splitting” at lower rolling temperatures because of strong initial texture. Substantial β phase mitigates the effect of starting texture at higher temperature so that “RD splitting” characterizes the basal pole figure. Weak starting texture and easy slip transfer for Ti-6Al-4V-0.1B alloy produce simultaneous TD and RD splittings in basal pole figures at all rolling temperatures.

A systematic investigation of the evolution of deformation microstructure and texture of twinning-induced plasticity (TWIP) steel during cold rolling has been carried out using electron backscatter diffraction and X-ray diffraction, as well as viscoplastic self-consistent simulations. It is found that extensive twinning leads to the formation of the strong Brass {110}〈112〉 and Goss {110}〈001〉 components in TWIP steel even at low strains. At higher reduction, heterogeneous deformation contributes to further strengthening of Brass (Bs) component. The origin and stability of Bs component as well as the impact of the evolution of texture and microstructure on mechanical anisotropy is further explored using viscoplastic self-consistent simulations.

This article presents the deformation behavior of high-strength pearlitic steel deformed by triaxial compression to achieve ultra-fine ferrite grain size with fragmented cementite. The consequent evolution of microstructure and texture has been studied using scanning electron microscopy, electron back-scatter diffraction, and X-ray diffraction. The synergistic effect of diffusion and deformation leads to the uniform dissolution of cementite at higher temperature. At lower temperature, significant grain refinement of ferrite phase occurs by deformation and exhibits a characteristic deformation texture. In contrast, the high-temperature deformed sample shows a weaker texture with cube component for the ferrite phase, indicating the occurrence of recrystallization. The different mechanisms responsible for the refinement of ferrite as well as the fragmentation of cementite and their interaction with each other have been analyzed. Viscoplastic self-consistent simulation was employed to understand deformation texture in the ferrite phase during triaxial compression.

In the present study, the β transus of boron-modified Ti-6Al-4V alloy was found to be almost equivalent to that of the normal alloy, although there is a difference in interstitial element content large enough to produce significant change. Compositional analysis confirms the scavenging ability of the boride particles that are present in the microstructure toward the interstitial elements. This factor can successfully retard the α → β phase transformation locally and increase the overall β transus of boron-added material.

The evolution of crystallographic texture during equal channel angular extrusion (ECAE) using route A has been investigated experimentally as well as by simulations for three types of materials: pure, commercially pure, and impure (cast) copper. The ECAE texture of copper can be compared with simple shear textures. However, there are deviations in terms of location of the respective components. These differences can be nearly reproduced using a recent flow line approach for ECAE deformation (L.S. Toth, R. Arruffat-Massion, L. Germain, S.C. Baik, and S. Suwas: Acta Mater., 2004, Vol. 52, pp. 1885-98) with the help of the viscoplastic self-consistent polycrystal model. The main texture components common to all three materials are $A_1_E$ and $B_E/\overline{B}_E$; the latter ones are significantly stronger in the cast material. The effect of further deformation on texture modification depends on material variables, such as purity, initial microstructure, and texture.

Evolution of texture in the high temperature β(B2) phase of the intermetallic alloy Ti-24Al-11Nb during thermomechanical processing has been studied. The temperature of rolling, amount of rolling deformation imparted, and the volume fraction of α 2 phase are found to influence the texture of the β phase. Textures observed generally do not correspond exactly to the commonly observed texture of bcc metals, alloys, or similar aluminide intermetallics.