Search

Estimates of physical and mechanical characteristics of materials at high strain rates play a key role in enhancing the accuracy of prediction of the stress–strain state of structures operating in extreme conditions. This article presents the results of a combined experimental–numerical study on the mechanical response of a thin-sheet rolled Ti-5Al-2.5Sn alloy to dynamic penetration. A specimen of a titanium alloy plate underwent punching with a hemispherical indenter at loading rates of 10, 5, 1, and 0.5 m/s. The evolution of the rear surface of specimens and crack configuration during deformation were observed by means of high-speed photography. Numerical simulations were performed to evaluate stress distribution in a titanium plate under specified loading conditions. To describe the constitutive behavior and fracture of the Ti-5Al-2.5Sn alloy at moderate strain rates, a physical-based viscoplastic material model and damage nucleation and growth relations were adopted in the computational model. The results of simulations confirm a biaxial stress state in the center of specimens prior to fracture initiation. The crack shapes and plate deflections obtained in the calculations are similar to those observed in experiments during dynamic punching.

The microstructural investigation, mechanical properties, and accumulation and dissipation of energies of the magnesium alloy Mg-2.9Y-1.3Nd in the recrystallized state and after severe plastic deformation (SPD) by extrusion are presented. The use of SPD provides the formation of a bimodal structure consisting of grains with an average size 15 µm and of ultrafine-grained grains with sizes less than 1 µm and volume fractions up to 50%, as well as of the fine particles of the second Mg24Y5 phases. It is established that grain refinement during extrusion is accompanied by an increase of the yield strength, increase of the tensile strength by 1.5 times, and increase of the plasticity by 1.8 times, all of which are due to substructural hardening, redistribution of the phase composition, and texture formation. Using infrared thermography, it was revealed that before the destruction of Mg-2.9Y-1.3Nd in the recrystallized state, there is a sharp jump of temperature by 10 °C, and the strain hardening coefficient becomes negative and amounts to (−6) GPa. SPD leads to a redistribution of thermal energy over the sample during deformation, does not cause a sharp increase in temperature, and reduces the strain hardening coefficient by 2.5 times.

The paper presents the experimental results of the mechanical behavior of Ti-5Al-2.5Sn alloy at high strain rates and elevated temperature. Flat smooth and notched specimens with notch radii of 10 mm, 5 mm, and 2.5 mm were used. The experimental studies were carried out using the high-velocity servo hydraulic test machine Instron VHS 40/50-20. The samples were heated with flat ceramic infrared emitters on average between 60 s and 160 s. The temperature control in the working part of specimens was carried out in real time using a chromel-alumel thermocouple. The digital image correlation (DIC) method was employed to investigate the evolution of local fields in the gauge section of the specimen. Data on the influence of stress triaxiality on the ductility of Ti-5Al-2.5Sn alloy were obtained under tension with strain rates ranging from 0.1 to 103 s−1 at a temperature of 673 K. It was found that, at 673 K, the ductility of Ti-5Al-2.5Sn alloy increases with the increasing strain rate for both smooth and notched specimens.

This article investigated the mechanical behavior of Ti-6Al-4V alloy (VT6, an analog to Ti Grade 5) in the range of strain rates from 0.1 to 103 s−1. Tensile tests with various notch geometries were performed using the Instron VHS 40/50-20 servo hydraulic testing machine. The Digital Image Correlation (DIC) analysis was employed to investigate the local strain fields in the gauge section of the specimen. The Keyence VHX-600D digital microscope was used to characterize full-scale fracture surfaces in terms of fractal dimension. At high strain rates, the analysis of the local strain fields revealed the presence of stationary localized shear bands at the initial stages of strain hardening. The magnitude of plastic strain within the localization bands was significantly higher than those averaged over the gauge section. It was found that the ultimate strain to fracture in the zone of strain localization tended to increase with the strain rate. At the same time, the Ti-6Al-4V alloy demonstrated a tendency to embrittlement at high stress triaxialities.

The present study investigates the effect of stress triaxiality on mechanical behavior and fracture of Ti-5Al-2.5Sn alloy in a practical relevant strain rate range from 0.1 to 1000 s−1. Tensile tests were carried out on flat smoothed and notched specimens using an Instron VHS 40/50-20 servo-hydraulic test machine. High-speed video registration was conducted by Phantom 711 Camera. Strain fields on the specimen gauge area were investigated by the digital image correlation method (DIC). The fracture surface relief was studied using digital microscope Keyence VHX-600D. Stress and strain fields during testing of the Ti-5Al-2.5Sn alloy were analyzed by the numerical simulation method. The evolution of strain fields at the investigated loading condition indicates that large plastic deformation occurs in localization bands. The alloy undergoes fracture governing by damage nucleation, growth, and coalescence in the localized plastic strain bands oriented along the maximum shear stresses. Results confirm that the fracture of near alpha titanium alloys has ductile behavior at strain rates from 0.1 to 1000 s−1, stress triaxiality parameter 0.33 < η < 0.6, and temperature close to 295 K.

Bioinert metals are used for medical implants and in some industrial applications. This study was performed to detect and analyze peculiarities that appear in the temperature distributions during quasi-static tensile testing of bioinert alloys. These alloys include VT1-0 titanium, Zr-1%Nb and Ti-45%Nb in both coarse-grain (CG) and ultrafine-grain (UFG) states. The crystal structure, as well as the crystal domain and grain sizes of these alloys in the UFG state, may be different from the CG versions and identifying the thermal signatures that occur during their deformation and fracture is of interest, as it may lead to an understanding of physical processes that occur during loading. By comparing the surface temperature distributions of specimens undergoing deformation under tensile loading to the distributions at maximum temperatures it was found that the observed differences depend on the alloy type, the alloy structural state and the thermal properties of structural defects in the specimen. Macro-defects were found in some specimens of VT1-0 titanium, Zr-1Nb and Ti-45Nb alloys in both the CG and UFG states. The average tensile strength of specimens containing defects was lower than that of specimens with no defects. Infrared thermography documents change in the thermal patterns of specimens as they are deformed under tensile loading and when the load stops changing or the specimen breaks.