Search

Purpose – The purpose of this paper is to focus on the technology and performance of the miniature microfluidic module for urea determination. The presented module was made using low-temperature co-fired ceramics (LTCC). It shows the possibility for the integration of the bioreceptor layers with structures that have been fabricated using modern microelectronic technology. Design/methodology/approach – The presented microfluidic module was fabricated using LTCC technology. The possibility for the fabrication of an enzymatic microreactor in a multilayer ceramic substrate, made of CeramTec glass ceramic (GC) material systems with an integrated thick-film heater, is studied. Different configurations of the LTCC/heater materials (gold, silvers and palladium-silver) are taken into account. The performance of the LTCC-based microfluidic module with the integrated heater and immobilized enzyme was examined experimentally. Findings – A compatible material for the heater embedded in the CeramTec GC-based structures was found. The preliminary measurements made for the test solution containing various concentrations of urea have shown stability (for seven days of operation) and a relatively high signal-to-noise ratio (above 3 pH units) for the microreactor’s output signal. Research limitations/implications – The presented research is a preliminary work which is focused on the fabrication of the LTCC-based microfluidic module, with an integrated heater and immobilized enzyme for urea determination. The device was positively tested using a model reaction of the hydrolysis of urea. However, urea concentration in real (biological) fluid should also be measured. Practical implications – The development of the LTCC-based microfluidic module for urea determination provides opportunity for the construction of a lab-on-chip, or μTAS-type system, for fast medical diagnoses and the continuous monitoring of various biochemical parameters, e.g. for estimating the effectiveness of hemodialysis. Originality/value – This paper shows the design, fabrication and performance of the novel microfluidic module for urea determination, made with LTCC technology. [ABSTRACT FROM AUTHOR]

Purpose – This paper aims to present a prototype of the diagnostic system for the examination of the distribution of the force applied by foot to substrate during usual human moving. Presented system is competitive to other currently available devices, thanks to sensors reliability, user-friendly operation manner and design based on cheap parts. The results of examinations are transmitted by radiomodem. Its recording and visualization are possible on either personal or mobile computers. Design/methodology/approach – During selection of the sensors substrate, many polymeric electrets were examined. Polyvinylidene fluoride films were selected, because they have good charge uniformity across the surface, wide range of acceptable temperatures, linear relation between mechanical stress and output signal and high resistance for squeezing. The system measures the charge generated in film. Findings – The pressures are recorded in relation to maximum value; therefore, measuring system does not require calibration. The simultaneous recording of data from all eight sensors allows tracking the signal without distortion. Originality/value – An array of sensors is installed in the shoe insole. The measuring device is fixed to the outer surface of the shoe. Its weight is 75 g. The range of transmission is suitable for examination in the natural environment, outside traditional consulting room. Software is dedicated for analysis of the pressure distribution in every moment of the foot movement. The system is suitable for examination of flat feet, diabetic foot and recovery progress after injures. [ABSTRACT FROM AUTHOR]

Purpose – This paper aims to investigate different properties of synthesized perovskite Sm0.9Sr0.1CoO3-δ and its potential for application in potentiometric oxygen sensors. Design/methodology/approach – The powder was obtained through solid-state reaction method and characterized by thermogravimetric/differential thermal analyzer and X-ray diffraction. It was used for both making a paste and pressing into rods for sintering. The prepared paste was deposited on alumina and yttria-stabilized zirconia substrates, by screen printing. Thick film conductivity, bulk conductivity and Seebeck coefficient of sintered rods were measured as a function of temperature. An oxygen concentration cell was fabricated with the screen-printed perovskite material as electrodes. Findings – Electrical conductivity of the bulk sample and thick film increases with the increase in temperature, showing semiconductor-like behavior, which is also indicated by relatively high values of the measured Seebeck coefficient. Estimated values of the activation energy for conduction are found to be of the same magnitude as those reported in the literature for similar composition. An investigation of Nernstian behavior of the fabricated cell confirmed that Sm0.9Sr0.1CoO3-δ is a promising material for application in oxygen potentiometric sensors. Originality/value – Gas sensor research is focused on the development of new sensitive materials. Although there is scarce information on SmCoO3-δ in the literature, it is mostly investigated for fuel cell applications. Results of this study imply that Sr-doped SmCoO3-δ is a good candidate material for oxygen potentiometric sensor. [ABSTRACT FROM AUTHOR]