Search

Nanostructured core–shell Si–Ta3N5 photoanodes were designed and synthesized to overcome charge transport limitations of Ta3N5 for photoelectrochemical water splitting. The core–shell devices were fabricated by atomic layer deposition of amorphous Ta2O5 onto nanostructured Si and subsequent nitridation to crystalline Ta3N5. Nanostructuring with a thin shell of Ta3N5 results in a 10-fold improvement in photocurrent compared to a planar device of the same thickness. In examining thickness dependence of the Ta3N5 shell from 10 to 70 nm, superior photocurrent and absorbed-photon-to-current efficiencies are obtained from the thinner Ta3N5 shells, indicating minority carrier diffusion lengths on the order of tens of nanometers. The fabrication of a heterostructure based on a semiconducting, n-type Si core produced a tandem photoanode with a photocurrent onset shifted to lower potentials by 200 mV. CoTiOx and NiOx water oxidation cocatalysts were deposited onto the Si–Ta3N5 to yield active photoanodes that with ...

Nanostructured core-shell Si-Ta

We report a hierarchically branched TiO2 nanorod structure that serves as a model architecture for efficient photoelectrochemical devices as it simultaneously offers a large contact area with the electrolyte, excellent light-trapping characteristics, and a highly conductive pathway for charge carrier collection. Under Xenon lamp illumination (UV spectrum matched to AM 1.5G, 88 mW/cm2 total power density), the branched TiO2 nanorod array produces a photocurrent density of 0.83 mA/cm2 at 0.8 V versus reversible hydrogen electrode (RHE). The incident photon-to-current conversion efficiency reaches 67% at 380 nm with an applied bias of 0.6 V versus RHE, nearly two times higher than the bare nanorods without branches. The branches improve efficiency by means of (i) improved charge separation and transport within the branches due to their small diameters, and (ii) a 4-fold increase in surface area which facilitates the hole transfer at the TiO2/electrolyte interface.

We synthesize vertically oriented core-shell nanowires with substoichiometric MoO(3) cores of ∼20-50 nm and conformal MoS(2) shells of ∼2-5 nm. The core-shell architecture, produced by low-temperature sulfidization, is designed to utilize the best properties of each component material while mitigating their deficiencies. The substoichiometric MoO(3) core provides a high aspect ratio foundation and enables facile charge transport, while the conformal MoS(2) shell provides excellent catalytic activity and protection against corrosion in strong acids.

Nanoparticulate tungsten oxide films were synthesized by pulsed electrodeposition. Particle sizes between 45 and ∼330 nm were achieved by varying pulse duration from 5 to 500 ms. Shorter pulses increased the rate of new particle nucleation above the rate of existing particle growth, allowing for the observed variations in size. Cathodic deposition voltage (−1 ∼ −3 V) had little effect on particle size. Compared to films prepared by continuous electrodeposition, nanoparticulate tungsten oxide films showed a higher photoactivity and greater current density for the hydrogen intercalation reaction. Functional improvements are explained by the smaller particle size and larger surface area of nanocrystalline tungsten oxide.

The formation of Pt nanowires (NWs) by atomic layer deposition on highly ordered pyrolytic graphite (HOPG) is investigated. Pt is deposited only at the step edges of HOPG and not on the basal planes, leading to the formation of laterally aligned Pt NWs. A growth model involving a morphological transition from 0-D to 1-D structures via coalescence is presented. The width of the NWs grows at a rate greater than twice the vertical growth rate. This asymmetry is ascribed to the wetting properties of Pt on HOPG as influenced by the formation of graphene oxide. A difference in Pt growth kinetics based on crystallographic orientation may also contribute.

We report a hierarchically branched TiO(2) nanorod structure that serves as a model architecture for efficient photoelectrochemical devices as it simultaneously offers a large contact area with the electrolyte, excellent light-trapping characteristics, and a highly conductive pathway for charge carrier collection. Under Xenon lamp illumination (UV spectrum matched to AM 1.5G, 88 mW/cm(2) total power density), the branched TiO(2) nanorod array produces a photocurrent density of 0.83 mA/cm(2) at 0.8 V versus reversible hydrogen electrode (RHE). The incident photon-to-current conversion efficiency reaches 67% at 380 nm with an applied bias of 0.6 V versus RHE, nearly two times higher than the bare nanorods without branches. The branches improve efficiency by means of (i) improved charge separation and transport within the branches due to their small diameters, and (ii) a 4-fold increase in surface area which facilitates the hole transfer at the TiO(2)/electrolyte interface.

Future generations of photoelectrodes for solar fuel generation must employ inexpensive, earth-abundant absorber materials in order to provide a large-scale source of clean energy. These materials tend to have poor electrical transport properties and exhibit carrier diffusion lengths which are significantly shorter than the absorption depth of light. As a result, many photoexcited carriers are generated too far from a reactive surface and recombine instead of participating in solar-to-fuel conversion. We demonstrate that plasmonic resonances in metallic nanostructures and multilayer interference effects can be engineered to strongly concentrate sunlight close to the electrode/liquid interface, precisely where the relevant reactions take place. On comparison of spectral features in the enhanced photocurrent spectra to full-field electromagnetic simulations, the contribution of surface plasmon excitations is verified. These results open the door to the optimization of a wide variety of photochemical processes by leveraging the rapid advances in the field of plasmonics.