Search

Gas sensors have played a critical role in healthcare, atmospheric environmental monitoring, military applications and so on. In particular, flexible sensing devices are of great interest, benefitting from flexibility and wearability. However, developing flexible gas sensors with a high sensitivity, great stability and workability is still challenging. In this work, multi-walled carbon nanotubes (MWCNTs) were grown on polydimethylsiloxane (PDMS) films, which were further modified with polyaniline (PANI) using a simple chemical oxidation synthesis. The superior flexibility of the PANI-MWCNTs/PDMS film enabled a stable initial resistance value, even under bending conditions. The flexible sensor showed excellent NH3 sensing performances, including a high response (11.8 ± 0.2 for 40 ppm of NH3) and a low limit of detection (10 ppb) at room temperature. Moreover, the effect of a humid environment on the NH3 sensing performances was investigated. The results show that the response of the sensor is enhanced under high humidity conditions because water molecules can promote the adsorption of NH3 on the PANI-MWCNTs/PDMS films. In addition, the PANI-MWCNTs/PDMS film sensor had the abilities of detecting NH3 in the simulated breath of patients with kidney disease and the freshness of shrimp. These above results reveal the potential application of the PANI-MWCNTs/PDMS sensor for monitoring NH3 in human breath and food. [ABSTRACT FROM AUTHOR]

As ordered porous materials, metal–organic frameworks (MOFs) have attracted tremendous attention in the field of energy conversion and storage due to their high specific surface area, permanent porosity, and tunable pore sizes. Here, MOF-derived MnO/C nanocomposites with regular octahedral shape were synthesized using a Mn-based analogue of the MIL-100 framework (Mn-MIL-100, MIL: Matérial Institut Lavoisier) as the precursor. Using aberration-corrected environmental transmission electron microscopy (ETEM), MnO nanocages with a diameter of approximately 20 nm were recognized in the MnO/C nanocomposites fabricated, dispersed in a microporous carbon matrix homogeneously. The nanocages are composed of MnO nanoparticles with a diameter of approximately 2 nm and with a single crystal structure. The specific surface area of the as-prepared MnO/C octahedra decreases to 256 m2 g−1 from 507 m2 g−1 of the Mn-MIL-100 precursor, whereas the total pore volume increases to 0.245 cm3 g−1, which is approximately 29% higher than that of the precursor (0.190 cm3 g−1). Additionally, when utilized as an electrode for supercapacitors, the MOF-derived MnO/C nanocomposite demonstrates a towering specific capacitance of 421 F g−1 at 0.5 A g−1 and good cycle stability (94%) after 5000 cycles. Our work reveals that the MnO nanoparticles in MOF-derived MnO/C nanocomposites exhibit nanocage structure characteristics, which might be inherited from the Mn-MIL-100 precursor with analogous supertetrahedron units. [ABSTRACT FROM AUTHOR]

Humidity sensors are important in industrial fields and human activities. Metal−organic frameworks (MOFs) and their derivatives are a class of promising humidity−sensing materials with the characteristics of a large specific surface area, high porosity, modifiable frameworks, and high stability. The drawbacks of MOFs, such as poor film formation, low electrical conductivity, and limited hydrophilicity, have been gradually overcome with the development of material science. Currently, it is moving towards a critical development stage of MOF−based humidity sensors from usability to ease of use, of which great challenges remain unsolved. In order to better understand the related challenges and point out the direction for the future development of MOF−based humidity sensors, we reviewed the development of such sensors based on related published work, focusing on six primary types (impedance, capacitive, resistive, fluorescent, quartz crystal microbalance (QCM), and others) and analyzed the sensing mechanism, material design, and sensing performance involved, and presented our thoughts on the possible future research directions. [ABSTRACT FROM AUTHOR]

The increasing threat of chloride ions (Cl−) has led researchers to explore efficient removal technologies. Sewage treatment with a double-layer hydroxide/oxide (LDH/LDO) is receiving increasing attention. In this work, Mg-Al LDO adsorbents were produced by the calcination of the Mg-Al LDH precursor, which was constituted by improved coprecipitation. The influence of calcination temperature, calcination time, adsorbent dosage, Cl− initial concentration, contact time, and adsorption temperature on Cl− elimination was investigated systematically. The experimental results showed that a better porous structure endowed the Mg-Al LDO with outstanding adsorption properties for Cl−. The adsorption process was well matched to the pseudo-second-order kinetics model and the Freundlich model. Under optimal conditions, more than 97% of the Cl− could be eliminated. Moreover, the removal efficiency was greater than 90% even after 11 adsorption–desorption cycles. It was found that the electrostatic interaction between Cl− and the positively charged Mg-Al LDO laminate, coupled with the reconstruction of the layer structure, was what dominated the Cl− removal process. [ABSTRACT FROM AUTHOR]

Thermally conductive and electrically insulating materials have attracted much attention due to their applications in the field of microelectronics, but through-plane thermal conductivity of materials is still low at present. In this paper, a simple and environmentally friendly strategy is proposed to improve the through-plane thermal conductivity of epoxy composites using a 3D boron nitride (3D-BN) framework. In addition, the effect of filler sizes in 3D-BN skeletons on thermal conductivity was investigated. The epoxy composite with larger BN in lateral size showed a higher through-plane thermal conductivity of 2.01 W/m·K and maintained a low dielectric constant of 3.7 and a dielectric loss of 0.006 at 50 Hz, making it desirable for the application in microelectronic devices. [ABSTRACT FROM AUTHOR]

Nanomaterials and nanostructures provide new opportunities to achieve high-performance optical and optoelectronic devices. Three-dimensional (3D) surfaces commonly exist in those devices (such as light-trapping structures or intrinsic grains), and here, we propose requests for nanoscale control over nanostructures on 3D substrates. In this paper, a simple self-assembly strategy of nanospheres for 3D substrates is demonstrated, featuring controllable density (from sparse to close-packed) and controllable layer (from a monolayer to multi-layers). Taking the assembly of wavelength-scale SiO2 nanospheres as an example, it has been found that textured 3D substrate promotes close-packed SiO2 spheres compared to the planar substrate. Distribution density and layers of SiO2 coating can be well controlled by tuning the assembly time and repeating the assembly process. With such a versatile strategy, the enhancement effects of SiO2 coating on textured silicon solar cells were systematically examined by varying assembly conditions. It was found that the close-packed SiO2 monolayer yielded a maximum relative efficiency enhancement of 9.35%. Combining simulation and macro/micro optical measurements, we attributed the enhancement to the nanosphere-induced concentration and anti-reflection of incident light. The proposed self-assembly strategy provides a facile and cost-effective approach for engineering nanomaterials at 3D interfaces. [ABSTRACT FROM AUTHOR]

Polymer-based composites with high thermal conductivity and dielectric breakdown strength have gained increasing attention due to their significant application potential in both power electronic devices and power equipment. In this study, we successfully prepared novel sandwich AlN/epoxy composites with various layer thicknesses, showing simultaneously and remarkably enhanced dielectric breakdown strength and thermal conductivity. The most optimized sandwich composite, with an outer layer thickness of 120 μm and an inner layer thickness of 60 μm (abbreviated as 120-60) exhibits a high through-plane thermal conductivity of 0.754 W/(m·K) (4.1 times of epoxy) and has a dielectric breakdown strength of 69.7 kV/mm, 8.1% higher compared to that of epoxy. The sandwich composites also have higher in-plane thermal conductivity (1.88 W/(m·K) for 120-60) based on the novel parallel models. The sandwich composites with desirable thermal and electrical properties are very promising for application in power electronic devices and power equipment. [ABSTRACT FROM AUTHOR]