Search

In this study, the samples of the ZnFe2O4 (ZFO) spinel ferrites nanoparticles (SFNPs), Co0.5Ni0.5Ga0.01Gd0.01Fe1.98O4 (CNGaGdFO) SFNPs and (Co0.5Ni0.5Ga0.01Gd0.01Fe1.98O4)x/(ZnFe2O4)y (x:y = 1:1, 1:2, 1:3, 2:1, 3:1 and 4:1) (CNGaGdFO)x/(ZFO)y spinel ferrite nanocomposites (NC) have been synthesized by both sol-gel and Green pulsed laser ablation in liquid (PLAL) approaches. All products were characterized by X-ray powder diffraction (XRD), scanning and transmission electron microscopies (SEM and TEM), elemental mappings and energy dispersive X-ray spectroscopy (EDX). It was objected to tune the magnetic properties of a soft spinel ferrite material with a softer one by mixing them with different fractions. Some key findings are as follows. M-H investigations revealed the exhibition of ferrimagnetic phases for all synthesized samples (except ZnFe2O4) that were synthesized by sol-gel or PLAL methods at both 300 K and 10 K. ZnFe2O4 ferrite NPs exhibits almost paramagnetic feature at 300 K and glass-like phase at very low temperatures below 19.23 K. At RT analyses, maximum saturation magnetization (MS) of 66.53 emu/g belongs to nanocomposite samples that was synthesized by sol-gel method and x:y ratio of 1:3. At 10 K analyses, MS,max = 118.71 emu/g belongs to same nanocomposite samples with ratio of 1:3. Maximum coercivities are 625 Oe belonging to CNGaGdFO and 3564 Oe belonging to NC sample that was obtained by sol-gel route having the 3:1 ratio. Squareness ratio (SQRs = Mr/MS) of NC sample (sol-gel, 4:1 ratio) is 0.371 as maximum and other samples have much lower values until a minimum of 0.121 (laser, 3:1) assign the multi-domain wall structure for all samples at 300 K. At 10 K data, just CNGaGdFO has 0.495 SQR value assigning single domain nature. The maximum values of effective crystal anisotropy constant (Keff) are 5.92 × 104 Erg/g and 2.4 × 105 Erg/g belonging to CNGaGdFO at 300 K and 10 K, respectively. Further, this sample has an internal anisotropy field Ha of 1953 Oe as largest at 300 K. At 10 K another sample (sol-gel, 3:1 ratio) has Ha,max of 11138 Oe which can also be classified as a soft magnetic material similar to other samples. Briefly, most magnetic parameters of NCs that were synthesized by sol-gel route are stronger than magnetic parameters of the NCs that were synthesized by PLAL at both temperatures. Some NC samples were observed to have stronger magnetic data as compared to magnetic parameters of Co0.5Ni0.5Ga0.01Gd0.01Fe1.98O4 NPs at 10 K. [ABSTRACT FROM AUTHOR]

Transparent and amorphous yttrium (Y)/Sialon thin films were successfully fabricated using pulsed laser deposition (PLD). The thin films were fabricated in three steps. First, Y/Sialon target was synthesized using spark plasma sintering technique at 1500 °C in an inert atmosphere. Second, the surface of the fabricated target was cleaned by grinding and polishing to remove any contamination, such as graphite and characterized. Finally, thin films were grown using PLD in an inert atmosphere at various substrate temperatures (RT to 500 °C). While the X-ray diffractometer (XRD) analysis revealed that the Y/Sialon target has β phase, the XRD of the fabricated films showed no diffraction peaks and thus confirming the amorphous nature of fabricated thin films. XRD analysis displayed that the fabricated thin films were amorphous while the transparency, measured by UV-vis spectroscopy, of the films, decreased with increasing substrate temperature, which was attributed to a change in film thickness with deposition temperature. X-ray photoelectron spectroscopy (XPS) results suggested that the synthesized Y/Sialon thin films are nearly homogenous and contained all target's elements. A scratch test revealed that both 300 and 500 °C coatings possess the tough and robust nature of the film, which can resist much harsh loads and shocks. These results pave the way to fabricate different Sialon doped materials for numerous applications. [ABSTRACT FROM AUTHOR]