Search

There is an urgent need to develop low cost electrochemical sensors wherein the sensor can be disposed after recording data, thereby eliminating the issue of inaccuracy arising from repeated sensing measurements, which plagues most conventional electrochemical sensors. This work is the first demonstration of a NiSe

Multifunctional electronics are attracting great interest with the increasing demand and fast development of wearable electronic devices. Here, we describe an epidermal strain sensor based on an all-carbon conductive network made from multi-walled carbon nanotubes (MWCNTs) impregnated with poly(dimethyl siloxane) (PDMS) matrix through a vacuum filtration process. An ultrasonication treatment was performed to complete the penetration of PDMS resin in seconds. The entangled and overlapped MWCNT network largely enhances the electrical conductivity (1430 S m-1), uniformity (remaining stable on different layers), reliable sensing range (up to 80% strain), and cyclic stability of the strain sensor. The homogeneous dispersion of MWCNTs within the PDMS matrix leads to a strong interaction between the two phases and greatly improves the mechanical stability (ca. 160% strain at fracture). The flexible, reversible and ultrathin (

There are many possible biomedical applications for titania nanoparticles (NPs) doped with rare earth elements (REEs), from dose enhancement and diagnostic imaging in radiotherapy, to biosensing. However, there are concerns that the NPs could disintegrate in the body thus releasing toxic REE ions to undesired locations. As a first step, we investigate how accurately the Ti/REE ratio from the NPs can be measured inside human cells. A quantitative analysis of whole, unsectioned, individual human cells was performed using proton microprobe elemental microscopy. This method is unique in being able to quantitatively analyse all the elements in an unsectioned individual cell with micron resolution, while also scanning large fields of view. We compared the Ti/REE signal inside cells to NPs that were outside the cells, non-specifically absorbed onto the polypropylene substrate. We show that the REE signal in individual cells co-localises with the titanium signal, indicating that the NPs have remained intact. Within the uncertainty of the measurement, there is no difference between the Ti/REE ratio inside and outside the cells. Interestingly, we also show that there is considerable variation in the uptake of the NPs from cell-to-cell, by a factor of more than 10. We conclude that the NPs enter the cells and remain intact. The large heterogeneity in NP concentrations from cell-to-cell should be considered if they are to be used therapeutically.

A colorimetric platform for influenza A virus detection was developed by using the high efficiency of enzymatic catalysis and the reduction of gold ions with hydrogen peroxide. Aptamer-functionalized magnetic microparticles were synthesized to capture the influenza A virus. This was followed by the binding of ConA-GOx-AuNPs to the H3N2 virus through the ConA-glycan interaction. The sandwich complex was subsequently dispersed in glucose solution to trigger an enzymatic reaction to produce hydrogen peroxide, which controlled the growth of gold nanoparticles and produced colored solutions. The determination of H3N2 concentration was realized by comparing the two differently colored gold nanoparticles. This method could detect the target virus as low as 11.16 μg ml−1. Furthermore, it opens new opportunities for sensitive and colorimetric detection of viruses and proteins.

Flexible and highly conductive single-walled carbon nanotube/polycellulose papers (SWCNT/PPs) were developed as current collectors for lithium-ion batteries by a simple and scalable process. The flexible electrodes based on SWCNT/PP conductors consisted of a unique three-dimensional interwoven structure of electrode materials and cellulose fibers with CNTs and exhibited flexibility, good electrochemical performance and excellent cyclic stability. Full cells using Li(4)Ti(5)O(12) and LiFePO(4) electrodes based on SWCNT/PPs showed a first discharge capacity of 153.5 mA h g(-1) with Coulombic efficiencies of 90.6% at 0.1 C and discharge capacity of 102.6 mA h g(-1) at high rate (10 C). Full cells based SWCNT/PP conductors showed higher capacities and lower electrochemical interfacial resistance compared to metallic current collectors. Half cells using anatase TiO(2) hierarchical spheres based on SWCNT/PP conductors also exhibited outstanding electrochemical performance, verifying the stability of SWCNT/PP conductors to various electrode materials. Our results demonstrated the potential versatility of composite electrodes and conductive SWCNT/PPs for flexible and portable micropower devices.

Composite nanocoating of poly(3,4-ethylenedioxythiophene)‐poly(styrenesulfonate) (PEDOT‐PSS) and aqueous dispersion of carbon nanotubes (CNT‐PSS) on lignocellulose wood microfibers has been developed to make conductive microfibers and paper sheets. To construct the multilayers on wood microfibers, cationic poly(ethyleneimine) (PEI) has been used in alternate deposition with anionic conductive PEDOT‐PSS and solubilized CNT‐PSS. Using a Keithley microprobe measurement system, current‐voltage measurements have been carried out on single composite microfibers after deposition of each layer to optimize the electrical properties of the coated microfibers. The conductivity of the resultant wood microfibers was in the range of 10 −2 ‐2 S cm −1 depending on the architecture of the coated layer. Further, the conductivity of the coated wood microfibers increased up to 20 S cm −1 by sandwiching multilayers of conductive co-polymer PEDOT‐PSS with CNT‐PSS through a polycation (PEI) interlayer. Moreover, paper hand sheets were manufactured from these coated wood microfibers with conductivity ranging from 1 to 20 S cm −1 . A paper composite structure consisting of conductive/dielectric/conductive layers that acts as a capacitor has also been fabricated and is reported. (Some figures in this article are in colour only in the electronic version)

Disposable analytical devices for developing sensitive and label-free monitoring of cancerous cells would be attractive for cancer research. Here, paper-based electroanalytical devices based on impedance spectrometry were applied for the study of K562 cells and the toxic effect of anticancer drugs. The proposed device integrating gold nanorods modified ITO electrodes could provide a biocompatible surface for immobilization of living cells maintaining their bioactivity. The impedance results exhibited good correlation to the logarithmic value of cell numbers ranging from 7.5 × 10(2) to 3.9 × 10(6) cells mL(-1) with a detection limit of 500 cells mL(-1). Furthermore, this strategy was used to evaluate the cytotoxic effects of arsenic trioxide and cyclophosphamide. Results obtained by the impedimetric method correlate well with the conventional cell viability assay. Cells exposed to drugs exhibited a prominent reduction of impedance data, showing an inverse dose-dependent relationship. This simple, cost-effective and portable paper-based electrochemical analytical device could provide a new impedance platform for applications in monitoring cell behavior, pharmacological studies and toxicological analyses.

In this study, two different supramolecular recognition architectures for impedimetric detection of DNA hybridization have been formed on disposable paper-supported inkjet-printed gold electrodes. The gold electrodes were fabricated using a gold nanoparticle based ink. The first recognition architecture consists of subsequent layers of biotinylated self-assembly monolayer (SAM), streptavidin and biotinylated DNA probe. The other recognition architecture is constructed by immobilization of thiol-functionalized DNA probe (HS-DNA) and subsequent backfill with 11-mercapto-1-undecanol (MUOH) SAM. The binding capacity and selectivity of the recognition architectures were examined by surface plasmon resonance (SPR) measurements. SPR results showed that the HS-DNA/MUOH system had a higher binding capacity for the complementary DNA target. Electrochemical impedance spectroscopy (EIS) measurements showed that the hybridization can be detected with impedimetric spectroscopy in picomol range for both systems. EIS signal indicated a good selectivity for both recognition architectures, whereas SPR showed very high unspecific binding for the HS-DNA/MUOH system. The factors affecting the impedance signal were interpreted in terms of the complexity of the supramolecular architecture. The more complex architecture acts as a less ideal capacitive sensor and the impedance signal is dominated by the resistive elements.

International audience; This paper shows that we can print on paper simple high frequency electronic devices such as resistances, capacitances or inductances, with values that can be changed in a controllable manner by an applied dc voltage. This tunability is achieved with the help of an ink containing functionalized carbon nanotubes and water. After the water is evaporated from the paper, the nanotubes remain steadily imprinted on paper, showing a semiconducting behavior and tunable electrical properties.