Search

Absorption spectroscopy is widely used in sensing and astronomy to understand molecular compositions on microscopic to cosmological scales. However, typical dispersive spectroscopic techniques require multichannel detection, fundamentally limiting the ability to detect extremely weak signals when compared to direct photometric methods. We report the realization of direct spectral molecular detection using a silicon nanophotonic waveguide resonator, obviating dispersive spectral acquisition. We use a thermally tunable silicon ring resonator with a transmission spectrum matched and cross-correlated to the quasi-periodic vibronic absorption lines of hydrogen cyanide. We show that the correlation peak amplitude is proportional to the number of overlapping ring resonances and gas lines, and that molecular specificity is obtained from the phase of the correlation signal in a single detection channel. Our results demonstrate on-chip correlation spectroscopy that is less restricted by the signal-to-noise penalty of other spectroscopic approaches, enabling the detection of faint spectral signatures.

We present a comparative experimental study of three silicon photonic echelle grating demultiplexers that are integrated with a Mach-Zehnder interferometer (MZI) launch structure. By appropriate choice of the MZI configuration, the temperature induced shift of the demultiplexer channel wavelengths can be suppressed (athermal) or enhanced (super-thermal) or be controlled by an on-chip micro-heater. The latter two configurations allow the channel wavelengths to be actively tuned using lower power than possible by temperature tuning a conventional echelle demultiplexer. In the athermal configuration, the measured channel spectral shift is reduced to less than 10 pm/°C, compared to the 83 pm/°C shift for an unmodified echelle device. In super-thermal operation an enhanced channel temperature tuning rate of 170 pm/°C is achieved. Finally, by modulating the MZI phase with an on-chip heater, the demultiplexer channels can be actively tuned to correct for ambient temperature fluctuations up to 20 °C, using a drive current of less than 20 mA.

An accurate model for the silicon refractive index including its temperature and wavelength dependence is critically important for many disciplines of science and technology. Currently, such a model for temperatures above 22°C in the optical communication bands is not available. The temperature dependence in the spectral response of integrated echelle grating filters made in silicon-on-insulator is solely determined by the optical properties of the slab waveguide, making it largely immune to dimensional uncertainties. This feature renders the echelle filters a reliable tool to evaluate the thermo-optic properties of silicon. Here we investigate the temperature dependence of silicon echelle filters for the wavelength range of both O and C bands, measured between 22°C to 80°C. We show that if a constant thermo-optic coefficient of silicon is assumed for each band, as is common in the literature, the predictions show an underestimate of up to 10% in the temperature-induced channel wavelength shift. We propose and assess a model of silicon refractive index that encompasses both the wavelength and temperature dependence of its thermo-optic coefficients. We start from literature data for bulk silicon and further refine the model using the echelle filter measurement results. This model is validated through accurate predictions of device channel wavelengths and their temperature dependence, including the quadratic term, over a wide wavelength and temperature range. This work also demonstrates a new high-precision method for characterizing the optical properties of a variety of materials.

Athermal design of integrated photonic devices can reduce the need for active temperature stabilization and consequently the energy required to operate photonic integrated circuits. For silicon photonic filters such as AWGs which employ wire or ridge waveguides, temperature insensitivity can be achieved using cladding materials with negative thermo-optic coefficients. On the other hand, in echelle grating filters the inteference takes place in the slab free-propagation region, and therefore the modal overlap with the cladding is small, rendering this method ineffective. In this work we present an approach to design an athermal echelle grating filter exploiting a temperature-synchronized Mach-Zehnder interferometer as input. This reduces the spectral shift over a temperature range of 20 K to less than ±45 pm compared to the 1.6 nm shift for the same echelle grating with a conventional waveguide input. Furthermore, the proposed design relies exclusively on a standard fabrication process for silicon-on-insulator photonic devices and exhibits a good tolerance to fabrication uncertainties.

Surface grating couplers are fundamental components in chip-based photonic devices to couple light between photonic integrated circuits and optical fibers. In this work, we report on a grating coupler with sub-decibel experimental coupling efficiency using a single etch process in a standard 220-nm silicon-on-insulator (SOI) platform. We specifically demonstrate a subwavelength metamaterial refractive index engineered nanostructure with backside metal reflector, with the measured peak fiber-chip coupling efficiency of -0.69 dB (85.3%) and 3 dB bandwidth of 60 nm. This is the highest coupling efficiency hitherto experimentally achieved for a surface grating coupler implemented in 220-nm SOI platform.

Coupling of light to and from integrated optical circuits has been recognized as a major practical challenge since the early years of photonics. The coupling is particularly difficult for high index contrast waveguides such as silicon-on-insulator, since the cross-sectional area of silicon wire waveguides is more than two orders of magnitude smaller than that of a standard single-mode fiber. Here, we experimentally demonstrate unprecedented control over the light coupling between the optical fiber and silicon chip by constructing the nanophotonic coupler with ultra-high coupling efficiency simultaneously for both transverse electric and transverse magnetic polarizations. We specifically demonstrate a subwavelength refractive index engineered nanostructure to mitigate loss and wavelength resonances by suppressing diffraction effects, enabling a coupling efficiency over 92% (0.32 dB) and polarization independent operation for a broad spectral range exceeding 100 nm.

Fiber-chip edge couplers are extensively used in integrated optics for coupling of light between planar waveguide circuits and optical fibers. In this work, we report on a new fiber-chip edge coupler concept with large mode size for silicon photonic wire waveguides. The coupler allows direct coupling with conventional cleaved optical fibers with large mode size while circumventing the need for lensed fibers. The coupler is designed for 220 nm silicon-on-insulator (SOI) platform. It exhibits an overall coupling efficiency exceeding 90%, as independently confirmed by 3D FiniteDifference Time-Domain (FDTD) and fully vectorial 3D Eigenmode Expansion (EME) calculations. We present two specific coupler designs, namely for a high numerical aperture single mode optical fiber with 6 µm mode field diameter (MFD) and a standard SMF-28 fiber with 10.4 µm MFD. An important advantage of our coupler concept is the ability to expand the mode at the chip edge without leading to high substrate leakage losses through buried oxide (BOX), which in our design is set to 3 µm. This remarkable feature is achieved by implementing in the SiO2 upper cladding thin high-index Si3N4 layers. The Si3N4 layers increase the effective refractive index of the upper cladding near the facet. The index is controlled along the taper by subwavelength refractive index engineering to facilitate adiabatic mode transformation to the silicon wire waveguide while the Siwire waveguide is inversely tapered along the coupler. The mode overlap optimization at the chip facet is carried out with a full vectorial mode solver. The mode transformation along the coupler is studied using 3DFDTD simulations and with fully-vectorial 3D-EME calculations. The couplers are optimized for operating with transverse electric (TE) polarization and the operating wavelength is centered at 1.55 µm. Web of Science 24 5 5038 5026

We report on the design, simulation and experimental demonstration of a new type of waveguide crossing based on subwavelength gratings in silicon waveguides. We used 3D finite-difference time-domain simulations to minimize loss, crosstalk and polarization dependence. Measurement of fabricated devices show that our waveguide crossings have a loss as low as −0.023 dB/crossing, polarization dependent loss of < 0.02 dB and crosstalk

A method is developed for extracting the coupling and loss coefficients of ring resonators from the peak widths, depths, and spacings of the resonances of a single resonator. Although the formulas used do not distinguish which coefficient is coupling and which is loss, it is shown how these coefficients can be disentangled based on how they vary with wavelength or device parameters.

By exploiting the small bend radius achievable using high-index-contrast silicon photonic wire waveguides, we demonstrate a new low power thermo-optic switch arranged in a dense, double spiral geometry. Such a design permits the waveguide length to be extended for increased phase shift, without the need for increased heated volume. This provides an effective means to reduce the power consumption of thermo-optic switches, as well as a compact geometry desirable for the development of switch arrays. A low switching power of 6.5 mW was obtained for a spiral-path Mach-Zehnder interferometer device having a 10% - 90% rise time of 14 micros. The switching power is shown to be reduced by more than 5 times compared to a Mach-Zehnder interferometer employing a conventional straight waveguide geometry.

We report the first Bragg gratings fabricated by Focused Ion Beam milling in optical waveguides. We observe striking features in the optical transmission spectra of surface relief gratings in silicon-on-insulator waveguides and achieve good agreement with theoretical results obtained using a novel adaptation of the beam propagation method and coupled mode theory. We demonstrate that leaky Higher Order Modes (HOM), often present in large numbers (although normally not observed) even in nominally single mode rib waveguides, can dramatically affect the Bragg grating optical transmission spectra. We investigate the dependence of the grating spectrum on grating dimensions and etch depth, and show that our results have significant implications for designing narrow spectral width gratings in high index waveguides, either for minimizing HOM effects for conventional WDM filters, or potentially for designing devices to capitalize on very efficient HOM conversion.

A nonlinear Al(x)Ga(1-x)As waveguide consisting of a quasi-phase matched heterostructure embedded in a microcavity has been designed and fabricated. The microcavity resonator is formed by Al(2)O(3)/Al(0.32)Ga(0.68)As multilayer mirrors located above and below the waveguide core. The cavity resonantly enhances the surface emitting second-harmonic generation. The SH conversion efficiency has been measured for wavelengths between l = 1525 and 1575 nm. A simple waveguide loss measurement technique based on the SH autocorrelation of short optical pulses in a III-V waveguide is also demonstrated.

We propose a fabrication tolerant polarization splitter and rotator (PSR) on the silicon-on-insulator platform based on the mode-coupling mechanism. The PSR consists of a silicon wire waveguide coupled to a taper-etched waveguide. Compared to previously reported PSRs based on directional couplers which are sensitive to fabrication variations, the partially etched taper structure can compensate for fabrication inaccuracies. In addition, the taper-etched geometry breaks both the horizontal and vertical symmetries of the waveguide, introducing an additional degree of design freedom to accommodate different upper cladding layers. The proposed PSR can be readily integrated in a planar waveguide circuit using e.g. SiO(2) cladding, making it compatible with typical metal back-end-of-line processes. Our simulation results show that the PSR has a low TM-to-TE polarization conversion loss of -0.09 dB in the C-band (or a conversion efficiency of 98%). A low TE-to-TE through insertion loss (-0.07 dB) and a very low polarization crosstalk (-30 dB) over a wide wavelength range exceeding 160 nm with a large fabrication tolerance (50 nm) are numerically demonstrated.

A complete photonic wire molecular biosensor microarray chip architecture and supporting instrumentation is described. Chip layouts with 16 and 128 independent sensors have been fabricated and tested, where each sensor can provide an independent molecular binding curve. Each sensor is 50 μm in diameter, and consists of a millimeter long silicon photonic wire waveguide folded into a spiral ring resonator. An array of 128 sensors occupies a 2 × 2 mm2 area on a 6 × 9 mm2 chip. Microfluidic sample delivery channels are fabricated monolithically on the chip. The size and layout of the sensor array is fully compatible with commercial spotting tools designed to independently functionalize fluorescence based biochips. The sensor chips are interrogated using an instrument that delivers sample fluid to the chip and is capable of acquiring up to 128 optical sensor outputs simultaneously and in real time. Coupling light from the sensor chip is accomplished through arrays of sub-wavelength surface grating couplers, and the signals are collected by a fixed two-dimensional detector array. The chip and instrument are designed so that connection of the fluid delivery system and optical alignment are automated, and can be completed in a few seconds with no active user input. This microarray system is used to demonstrate a multiplexed assay for serotyping E. coli bacteria using serospecific polyclonal antibody probe molecules. © 2013 Optical Society of America.

For silicon wire based ring resonator biosensors, we investigate the simultaneous retrieval of changes in the fluidic refractive index ∆n(c) and surface adsorbed molecular film thickness ∆d(F). This can be achieved by monitoring the resonance shifts of the sensors operating in the TE and TM polarizations at the same time. Although this procedure is straightforward in principle, significant retrieval errors can be introduced due to deviations in the sensor waveguide cross-sections from their nominal values in the range commonly encountered for silicon photonic wire devices. We propose a method of determining the fabricated waveguide size using the group indices derived from measured free spectral range (FSR) of the resonators. We further demonstrate that using experimentally measured group index values, the waveguide size can be determined to accuracies of ± 2 nm in width and ± 1 nm in height. By using this procedure, ∆n(c) and ∆d(F) can be obtained to a precision of within 10% of the true values using optically measurable parameters, improving the retrieval accuracy by more than 3 times.

In this paper, athermal silicon waveguides using bridged subwavelength grating (BSWG) structures are proposed and investigated. The realization of temperature-independent BSWG waveguides for both polarizations is demonstrated numerically and experimentally. SU-8 polymer is used as the cladding material to compensate for the positive thermo-optic (TO) coefficient (dn/dT) of silicon. We investigate the dependence of the effective TO coefficient of BSWG waveguides on both the bridge width and grating duty cycle. The BSWG waveguides have a width of 490 nm, a height of 260 nm, and a grating pitch of 250 nm. Athermal behavior is achieved for both the transverse-magnetic (TM) and the transverse-electric (TE) polarized light for a variety of bridge width and duty cycle combinations. Furthermore, the BSWGs can be designed to be athermal for both TE and TM polarization simultaneously. © 2012 Optical Society of America.

Directional couplers are extensively used devices in integrated optics, but suffer from limited operational wavelength range. Here we use, for the first time, the dispersive properties of sub-wavelength gratings to achieve a fivefold enhancement in the operation bandwidth of a silicon-oninsulator directional coupler. This approach does not compromise the size or the phase response of the device. The sub-wavelength grating based directional coupler we propose covers a 100nm bandwidth with an imbalance of =0.6dB between its outputs, as supported by full 3D FDTD simulations. © 2012 Optical Society of America.

We demonstrate all-optical wavelength conversion at 10 Gb/s for differential phase-shift keyed (DPSK) data signals in the C-band, based on four-wave mixing (FWM) in a silicon ring resonator. Error-free operation with a system penalty of ~ 4.1 dB at 10-9 BER is achieved.

A comprehensive investigation of real-time temperature-induced resonance shift cancellation for silicon wire based biosensor arrays is reported for the first time. A reference resonator, protected by either a SU8 or SiO(2) cladding layer, is used to track temperature changes. The temperature dependence of resonators in aqueous solutions, pertinent to biosensing applications, is measured under steady-state conditions and the operating parameters influencing these properties are discussed. Real-time measurements show that the reference resonator resonances reflect the temperature changes without noticeable time delay, enabling effective cancellation of temperature-induced shifts. Binding between complementary IgG protein pairs is monitored over 4 orders of magnitude dynamic range down to a concentration of 20 pM, demonstrating a resolvable mass of 40 attograms. Reactions are measured over time periods as long as 3 hours with high stability, showing a scatter corresponding to a fluid refractive index fluctuation of ± 4 × 10(-6) in the baseline data. Sensor arrays with a SU8 protective cladding are easy to fabricate, while oxide cladding is found to provide superior stability for measurements involving long time scales.

We demonstrate a terahertz bandwidth silicon nanowire based radio-frequency spectrum analyzer using cross-phase modulation. We show that the device provides accurate characterization of 640Gbaud on-off-keyed data stream and demonstrate its potential for optical time-division multiplexing optimization and optical performance monitoring of ultrahigh speed signals on a silicon chip. We analyze the impact of free carrier effects on our device, and find that the efficiency of the device is not reduced by two-photon or free-carrier absorption, nor its accuracy compromised by free-carrier cross-chirp.

We demonstrate all-optical time division demultiplexing from 160Gb/s to 10Gb/s in the C-band, based on four-wave mixing (FWM) in a silicon nanowire. We achieve error-free operation with a system penalty of approximately 3.9dB at 10(-9) BER.

We present an ultra-compact comb filter using an add-drop ring resonator with an Archimedean spiral cavity. The cavity consists of two interleaved spiral branches which are connected in the center using arcs of circle of a radius that causes minimum bend loss. We describe the design procedure and examine the physical parameters governing the resonator performance. As an example, we demonstrate experimentally a comb filter with a 25 GHz channel spacing made of silicon photonic wires and only occupies an area of 80 × 90 µm2, approximately a 70 fold size reduction compared to a racetrack resonator. The filter transmission is free of spurious reflections, attesting to the smooth transition between different sections of the resonator cavity. Over a 40 channel wavelength span, the filter exhibits a quality factor Q > 35,000, extinction ratios > 10 dB, and an excellent power uniformity with variations < 0.5 dB for both the through and drop ports.

We report on several new types of sub-wavelength grating (SWG) gradient index structures for efficient mode coupling in high index contrast slab waveguides. Using a SWG, an adiabatic transition is achieved at the interface between silicon-on-insulator waveguides of different geometries. The SWG transition region minimizes both fundamental mode mismatch loss and coupling to higher order modes. By creating the gradient effective index region in the direction of propagation, we demonstrate that efficient vertical mode transformation can be achieved between slab waveguides of different core thickness. The structures which we propose can be fabricated by a single etch step. Using 3D finite-difference time-domain simulations we study the loss, polarization dependence and the higher order mode excitation for two types (triangular and triangular-transverse) of SWG transition regions between silicon-on-insulator slab waveguides of different core thicknesses. We demonstrate two solutions to reduce the polarization dependent loss of these structures. Finally, we propose an implementation of SWG structures to reduce loss and higher order mode excitation between a slab waveguide and a phase array of an array waveguide grating (AWG). Compared to a conventional AWG, the loss is reduced from -1.4 dB to < -0.2 dB at the slab-array interface.

We present experimental and theoretical results of label-free molecular sensing using the transverse magnetic mode of a 0.22 mum thick silicon slab waveguide with a surface grating implemented in a guided mode resonance configuration. Due to the strong overlap of the evanescent field of the waveguide mode with a molecular layer attached to the surface, these sensors exhibit high sensitivity, while their fabrication and packaging requirements are modest. Experimentally, we demonstrate a resonance wavelength shift of approximately 1 nm when a monolayer of the protein streptavidin is attached to the surface, in good agreement with calculations based on rigorous coupled wave analysis. In our current optical setup this shift corresponds to an estimated limit of detection of 0.2% of a monolayer of streptavidin.

We present the design and numerical simulation results for a silicon waveguide modulator based on carrier depletion in a linear array of periodically interleaved PN junctions that are oriented perpendicular to the light propagation direction. In this geometry the overlap of the optical waveguide mode with the depletion region is much larger than in designs using a single PN junction aligned parallel to the waveguide propagation direction. Simulations predict that an optimized modulator will have a high modulation efficiency of 0.56 V.cm for a 3V bias, with a 3 dB frequency bandwidth of over 40 GHz. This device has a length of 1.86 mm with a maximum intrinsic loss of 4.3 dB at 0V bias, due to free carrier absorption. (C) 2009 Optical Society of America

We demonstrate efficient, low power, continuous-wave four-wave mixing in the C-band, using a high index doped silica glass micro ring resonator having a Q-factor of 1.2 million. A record high conversion efficiency for this kind of device is achieved over a bandwidth of 20nm. We show theoretically that the characteristic low dispersion enables phase-matching over a tuning range > 160nm.

We demonstrate folded waveguide ring resonators for biomolecular sensing. We show that extending the ring cavity length increases the resonator quality factor, and thereby enhances the sensor resolution and minimum level of detection, while at the same time relaxing the tolerance on the coupling conditions to provide stable and large resonance contrast. The folded spiral path geometry allows a 1.2 mm long ring waveguide to be enclosed in a 150 microm diameter sensor area. The spiral cavity resonator is used to monitor the streptavidin protein binding with a detection limit of approximately 3 pg/mm(2), or a total mass of approximately 5 fg. The real time measurements are used to analyze the kinetics of biotin-streptavidin binding.

A ring resonator in SOI photonic wire waveguides is demonstrated using a compact MMI coupler with 3mum x 9 mum footprint as the coupling element. We achieved high bandwidth of 0.25 nm, and a quality factor Q of ~ 6000 for rings with a radius of 50 mum. Unlike directional coupler based rings, these resonators have a wavelength independent Q and extinction ratio over more than 30 nm wavelength range, and there is no loss penalty for increasing the bandwidth. Compared to their directional coupler based counterparts, these resonators also have less demanding fabrication requirements and are compatible with high speed signal processing and optical delay lines.

We propose a new waveguide resonator device with a mirror cavity and a multimode interference (MMI) coupler. We present simulation results for the silicon wire MMI coupler with suppressed reflections and its use as a coupling element in the resonator cavity, built on the silicon-on-insulator waveguide platform. Tapering structures used in the reflection suppression were optimized, and the wavelength dependency of a conventional MMI was compared to that of the MMI with reflection suppression. Equations relating the power transfer of the two-mirror MMI-coupled resonator and quality factor were derived. The device was also studied using finite difference time domain simulation by both pulse and continuous wave excitation. The resonator does not require bend waveguides, it has the advantages of having no bend loss and a compact layout. The resonator device has a very small footprint of 3 mum x 30 mum, and a quality factor of 516.

We demonstrate a 50-channel high-resolution arrayed waveguide grating microspectrometer with a 0.2 nm channel spacing on a silicon-on-insulator (SOI) platform. The chip size is 8 mm x 8 mm. High channel density and spectral resolution are achieved using high aspect ratio 0.6 mum x 1.5 mum waveguide apertures to inject the light into the input combiner and to intercept different spectral channels at the output combiner focal region. The measured crosstalk is

We present an analysis of Fourier-transform arrayed waveguide gratings in the Fresnel diffraction regime. We report a distinct spatial modulation of the interference pattern referred to as the Moiré-Talbot effect. The effect and its influence in a FT AWG device is explained by deriving an original analytical expression for the modulated field, and is also confirmed by numerical simulations using the angular spectrum method to solve the Fresnel diffraction integral. We illustrate the retrieval of spectral information in a waveguide Fourier-transform spectrometer in the presence of the Moiré-Talbot effect. The simulated device comprises two interleaved waveguide arrays each with 180 waveguides and the interference order of 40. It is designed with a Rayleigh spectral resolution of 0.1 nm and 8 nm bandwidth at wavelength lambda approximately 1.5 mum. We also demonstrate by numerical simulations that the spectrometer crosstalk is reduced from -20 dB to -40 dB by Gaussian apodization.

Concept, theory and simulations of a new type of waveguide device, a multiaperture Fourier-transform planar waveguide spectrometer, are presented. The spectrometer is formed by an array of Mach-Zehnder interferometers generating a wavelength dependent spatial fringe pattern at the array output. The input light spectrum is calculated using a discrete Fourier transformation of the output spatial fringes. The multiaperture input significantly increases the optical throughput (étendue) compared to conventional single input spectrometers. Design rules for the arrayed spectrometer are deduced from performance specifications such as wavelength range and spectral resolution. A design example with spectral resolution 0.025 nm and range 2.5 nm is presented, where the optical throughput is increased by a factor of 200 compared to a single input device.