Search

Objective. This work investigates the use of passive luminescence detectors to determine different types of averaged linear energy transfer (LET-) for the energies relevant to proton therapy. The experimental results are compared to reference values obtained from Monte Carlo simulations. Approach. Optically stimulated luminescence detectors (OSLDs), fluorescent nuclear track detectors (FNTDs), and two different groups of thermoluminescence detectors (TLDs) were irradiated at four different radiation qualities. For each irradiation, the fluence- (LET-f) and dose-averaged LET (LET-d) were determined. For both quantities, two sub-types of averages were calculated, either considering the contributions from primary and secondary protons or from all protons and heavier, charged particles. Both simulated and experimental data were used in combination with a phenomenological model to estimate the relative biological effectiveness (RBE). Main results. All types ofLET-could be assessed with the luminescence detectors. The experimental determination ofLET-fis in agreement with reference data obtained from simulations across all measurement techniques and types of averaging. On the other hand,LET-dcan present challenges as a radiation quality metric to describe the detector response in mixed particle fields. However, excluding secondaries heavier than protons from theLET-dcalculation, as their contribution to the luminescence is suppressed by ionization quenching, leads to equal accuracy betweenLET-fandLET-d. Assessment of RBE through the experimentally determinedLET-dvalues agrees with independently acquired reference values, indicating that the investigated detectors can determineLET-with sufficient accuracy for proton therapy. Significance. OSLDs, TLDs, and FNTDs can be used to determineLET-and RBE in proton therapy. With the capability to determine dose through ionization quenching corrections derived fromLET-, OSLDs and TLDs can simultaneously ascertain dose,LET-, and RBE. This makes passive detectors appealing for measurements in phantoms to facilitate validation of clinical treatment plans or experiments related to proton therapy., (Creative Commons Attribution license.)

Objective. This work investigates the use of Al 2 O 3 :C and Al 2 O 3 :C,Mg optically stimulated luminescence (OSL) detectors to determine both the dose and the radiation quality in light ion beams. The radiation quality is here expressed through either the linear energy transfer (LET) or the closely related metric Q eff , which depends on the particle's speed and effective charge. The derived LET and Q eff values are applied to improve the dosimetry in light ion beams. Approach. OSL detectors were irradiated in mono-energetic 1 H-, 4 He-, 12 C-, and 16 O-ion beams. The OSL signal is associated with two emission bands that were separated using a pulsed stimulation technique and subjected to automatic corrections based on reference irradiations. Each emission band was investigated independently for dosimetry, and the ratio of the two emission intensities was parameterized as a function of fluence- and dose-averaged LET, as well as Q eff . The determined radiation quality was subsequently applied to correct the dose for ionization quenching. Main results. For both materials, the Q eff determinations in 1 H- and 4 He-ion beams are within 5 % of the Monte Carlo simulated values. Using the determined radiation quality metrics to correct the nonlinear (ionization quenched) detector response leads to doses within 2 % of the reference doses. Significance. Al 2 O 3 :C and Al 2 O 3 :C,Mg OSL detectors are applicable for dosimetry and radiation quality estimations in 1 H- and 4 He-ions. Only Al 2 O 3 :C,Mg shows promising results for dosimetry in 12 C-ions. Across both materials and the investigated ions, the estimated Q eff values were less sensitive to the ion types than the estimated LET values were. The reduced uncertainties suggest new possibilities for simultaneously estimating the physical and biological dose in particle therapy with OSL detectors., (Creative Commons Attribution license.)

Ionization quenching in ion beam dosimetry is often related to the fluence- or dose-averaged linear energy transfer (LET). Both quantities are however averaged over a wide LET range and a mixed field of primary and secondary ions. We propose a novel method to correct the quenched luminescence in scintillators exposed to ion beams. The method uses the energy spectrum of the primaries and accounts for the varying quenched luminescence in heavy, secondary ion tracks through amorphous track structure theory. The new method is assessed against more traditional approaches by correcting the quenched luminescence response from the BCF-12, BCF-60, and 81-0084 plastic scintillators exposed to a 100 MeV pristine proton beam in order to compare the effects of the averaged LET quantities and the secondary ions. Calculations and measurements show that primary protons constitute more than 92% of the energy deposition but account for more than 95% of the luminescence signal in the scintillators. The quenching corrected luminescence signal is in better agreement with the dose measurement when the secondary particles are taken into account. The Birks model provided the overall best quenching corrections, when the quenching corrected signal is adjusted for the number of free model parameters. The quenching parameter kB for the BCF-12 and BCF-60 scintillators is in agreement with literature values and was found to be [Formula: see text] [Formula: see text]m keV -1 for the 81-0084 scintillator. Finally, a fluence threshold for the 100 MeV proton beam was calculated to be of the order of 10 10 cm -2 , corresponding to 110 Gy, above which the quenching increases non-linearly and the Birks model no longer is applicable.

A ripple filter (RiFi) is a passive energy modulator used in scanned particle therapy to broaden the Bragg peak, thus lowering the number of accelerator energies required for homogeneous target coverage, which significantly reduces the irradiation time. As we have previously shown, a new 6 mm thick RiFi with 2D groove shapes produced with 3D printing can be used in carbon ion treatments with a similar target coverage and only a marginally worse planning conformity compared to treatments with in-use 3 mm thick RiFis of an older 1D design. Where RiFis are normally not used with protons due to larger scattering and straggling effects, this new design would be beneficial in proton therapy too. Measurements of proton Bragg curves and lateral beam profiles were carried out for different RiFi designs and thicknesses as well as for no RiFi at the Heidelberg Ionenstrahl-Therapiezentrum. Base data for proton treatment planning were generated with the Monte Carlo code SHIELD-HIT12A with and without the 2D 6 mm RiFi. Plans on spherical targets in water were calculated with TRiP98 for a systematic RiFi performance analysis and for comparisons with carbon ion plans for the same respective energy depth step sizes. Plans for 9 stage I static non small cell lung cancer patients were calculated with Eclipse 13.7.15. Dose-volume-histograms, spatial dose distributions and dosimetric indexes were used for plan evaluation. Measurements confirm the functionality of the new 2D RiFi design, which reduces the beam spot size compared to 1D RiFis of the same thickness. Planning studies show that a 6 mm thick 2D RiFi could be used in proton therapy to lower the irradiation time. Although slightly worse planning conformity and dose homogeneity were found for plans with the RiFi compared to plans without, satisfactory results within the planning objective were obtained for all cases.