Search

In this research work, a coated paper was prepared with poly (butylene adipate-co-terephthalate) (PBAT) film to explore its use in eco-friendly food packaging. The paper was coated with PBAT film for packaging using hot pressing, a production method currently employed in the packaging industry. The coated papers were evaluated for their structural, mechanical, thermal, and barrier properties. The structural morphology and chemical analysis of the coated paper confirmed the consistent formation of PBAT bi-layered on paper surfaces. Surface coating with PBAT film increased the water resistance of the paper samples, as demonstrated by tests of barrier characteristics, including the water vapor transmission rate (WVTR), oxygen transmission rate (OTR), and water contact angle (WCA) of water drops. The transmission rate of the clean paper was 2010.40 cc m−2 per 24 h for OTR and 110.24 g m−2 per 24 h for WVTR. If the PBAT-film was coated, the value decreased to 91.79 g m−2 per 24 h and 992.86 cc m−2 per 24 h. The hydrophobic nature of PBAT, confirmed by WCA measurements, contributed to the enhanced water resistance of PBAT-coated paper. This result presents an improved PBAT-coated paper material, eliminating the need for adhesives and allowing for the fabrication of bi-layered packaging. [ABSTRACT FROM AUTHOR]

The aim of this study was to develop bio-based adhesives that can be used for various packaging papers. In addition to commercial paper samples, papers produced from harmful plant species in Europe, such as Japanese Knotweed and Canadian Goldenrod, were used. In this research, methods were developed to produce bio-based adhesive solutions in combinations of tannic acid, chitosan, and shellac. The results showed that the viscosity and adhesive strength of the adhesives were best in solutions with added tannic acid and shellac. The tensile strength with adhesives of tannic acid and chitosan was 30% better than with commercial adhesives and 23% for combinations of shellac and chitosan. For paper from Japanese Knotweed and Canadian Goldenrod, the most durable adhesive was pure shellac. Because the surface morphology of the invasive plant papers was more open and had numerous pores compared to the commercial papers, the adhesives penetrated the paper structure and filled the voids. There was less adhesive on the surface and the commercial papers achieved better adhesive properties. As expected, the bio-based adhesives also showed an increase in peel strength and exhibited favorable thermal stability. In summary, these physical properties support the use of bio-based adhesives use in different packaging applications. [ABSTRACT FROM AUTHOR]

The manufacturing of paper with new functional properties is a current problem today. A method of modifying the surface layer of paper by the partial dissolution of cellulose on its surface is proposed. N-Methylmorpholine-N-oxide (NMMO) is proposed for use as a solvent, the regeneration of which provides an environmentally friendly process. It was shown that among the possible hydrate forms of the solvent, the monohydrate and higher-melting forms are optimal for modifying the paper surface. The temperature–time modes of processing were revealed and the weight gain and density increase in the course of modification were estimated. The structural and morphological features of the original and modified paper were studied by X-ray imaging and scanning microscopy. The NMMO surface treatment makes it possible to vary the air permeability of the paper, making it practically non-permeable. The capillary and pore system were radically transformed after the partial dissolution of cellulose and its coagulation, as the formed cellulose film isolates them, which leads to a decrease in surface absorbency. The processing conditions allowing for the optimization of the optical and strength properties of the modified paper samples are revealed. The resulting paper with a modified N-methylmorpholine-N-oxide surface layer can be used for printing valuable documents. [ABSTRACT FROM AUTHOR]

During the storage of celluloid pictures for animation films over half a century, an interleave paper adhered to acrylic paint. The purpose of this study is to establish a methodology to cleanly remove the paper from the paint. A layered film, a replica of the celluloid pictures, adhered with paper was prepared and immersed in water or ethanol. The effect of these solvents on the peeling behavior was investigated using a peel test. The maximum peel force for the dry layered film in was distributed at ~0.5 N, independently of the peel speed. The peel force was significantly reduced after the layered film was immersed in pure water or ethanol. A morphological observation revealed that the dry paper was peeled off via the cohesive failure of the paper. After the layered film was immersed in pure water, the paper was also peeled off via cohesive failure. The layered film immersed in ethanol was peeled off at the paper/paint interface. To clear the effect of the volume change in the paint on peel behavior, the relative volume was determined via image analysis. The relative volume of paint was 1.56 in pure water and 1.37 in ethanol. It can be considered that the large difference in the volume of paint induces a large shear stress at the paint/paper interface. [ABSTRACT FROM AUTHOR]

The hydroxyl groups on the cellulose macromolecular chain cause the cellulose surface to have strong reactivity. In this study, 1H, 1H, 2H, 2H-perfluorodecyltriethoxysilane (PDOTES) was used to modify cellulose to improve its triboelectric properties, and a triboelectric nanogenerator (TENG) was assembled. The introduction of fluorine groups reduced the surface potential of cellulose and turned it into a negative phase, which enhanced the ability to capture electrons. The electrical properties increased by 30% compared with unmodified cellulose. According to the principles of TENGs, a self-powered human-wearable device was designed using PDOTES-paper, which could detect movements of the human body, such as walking and running, and facilitated a practical method for the preparation of efficient wearable sensors. [ABSTRACT FROM AUTHOR]

There is current interest in replacing petroleum-based additives in consumer paper products with abundantly available, renewable and sustainable biopolymers such as lignin-containing cellulose nanofibers (LCNFs) and cottonseed protein. This research characterized the performance of cottonseed protein isolate with/without LCNFs to increase the dry strength of filter paper. The application of 10% protein solution with 2% LCNFs as an additive improved the elongation at break, tensile strength and modulus of treated paper products compared to the improved performance of cottonseed protein alone. Improvements in tensile modulus and tensile strength were greatest for samples containing larger amounts of lignin and a greater degree of polymerization than for those with less lignin from the same biomass sources. [ABSTRACT FROM AUTHOR]

Hydrophobic coatings are of utmost importance for many applications of paper-based materials. However, to date, most coating methods demand vast amounts of chemicals and solvents. Frequently, fossil-based coating materials are being used and multiple derivatization reactions are often required to obtain desired performances. In this work, we present a solvent-free paper-coating process, where olive oil as the main biogenic component is being used to obtain a hydrophobic barrier on paper. UV-induced thiol-ene photocrosslinking of olive oil was pursued in a solvent-free state at a wavelength of 254 nm without addition of photoinitiator. Optimum reaction conditions were determined in advance using oleic acid as a model compound. Paper coatings based on olive oil crosslinked by thiol-ene reaction reach water contact angles of up to 120°. By means of Fourier transform infrared spectroscopy and differential scanning calorimetry, a successful reaction and the formation of a polymer network within the coating can be proven. These results show that click-chemistry strategies can be used to achieve hydrophobic polymeric paper coatings while keeping the amount of non-biobased chemicals and reaction steps at a minimum. [ABSTRACT FROM AUTHOR]

Cellulose is a promising biomass material suitable for high volume applications. Its potential lies in sustainability, which is becoming one of the leading trends in industry. However, there are certain drawbacks of cellulose materials which limit their use, especially their high wettability and low barrier properties, which can be overcome by applying thin coatings. Plasma technologies present a high potential for deposition of thin environmentally friendly and recyclable coatings. In this paper, two different plasma reactors were used for coating two types of cellulose-based substrates with hexamethyldisiloxane (HMDSO). The changes in surface characteristics were measured by atomic force microscopy (AFM), scanning electron microscopy (SEM), surface free energy and contact angles measurements, X-ray photoelectron spectroscopy (XPS), and secondary ion mass spectrometry (SIMS). Successful oleofobization was observed for an industrial scale reactor where pure HMDSO was used in the absence of oxygen. [ABSTRACT FROM AUTHOR]